Williams-Sonoma TABOR KNOB User manual

Assembly Instructions
Instructions
d’assemblage
Instrucciones de Ensamblaje
Williams-Sonoma Inc.
Pottery Barn – Pottery Barn Teen – Pottery Barn Kids – Williams Sonoma Home – West Elm – Rejuvenation – Mark and Graham
9-September-2021
1/2
A
TABOR KNOB/PULL/BIN PULL

Assembly Instructions
Instructions
d’assemblage
Instrucciones de Ensamblaje
Williams-Sonoma Inc.
Pottery Barn – Pottery Barn Teen – Pottery Barn Kids – Williams Sonoma Home – West Elm – Rejuvenation – Mark and Graham
9-September-2021
2/2
© 2021 Williams-Sonoma, Inc. A
y.
CALIFORNIA PROPOSITION 65 WARNING: This product can expose you to chemicals including Lead
which isknown tothe State ofCalifornia to cause cancer and birth defects orother reproductiveharm. For
more information go to www.P65warnings.ca.gov.
FASTENERS INCLUDED :
Knob: (1) of each length: 1" / 1-1/2" / 1-3/4" #8-32 Truss head screw
Pull: (2) of each length: 1" / 1-1/2" / 1-3/4" #6-32 Oval head slotted screws (use with T-Nuts)
(2) T-nut (use with existing holes)
(2)Oval head slotted wood screw (use when there are no existing holes)
Bin Pull: (2) of each length: 1" / 1-1/2" / 1-3/4" #8-32 Truss head screws
MOUNTING INSTRUCTIONS:
This hardware includes fasteners that are designed for drawer fronts and doors with a thickness range between 1/2" and 1-1/2"
inches. If your drawer fronts and doors are thicker or thinner than this range, please obtain the appropriate size screw from your local
hardware store. With slotted screws, wrap the tip of the screw driver with one layer of masking tape to reduce the chance of marring
the finish.
KNOB: Carefully determine a desired knob location and use a drill with a 3/16" diameter drill bit to make a hole through the
drawer front or door. Choose a screw which protrudes about 1/8" - 1/4" from the face of the drawer front or door. Use a screwdriver to
tighten the screw while gently holding the knob. DO NOT USE A POWERED SCREW DRIVER.
PULL: WITH NO PREDRILLED HOLES: Carefully determine a desired pull location. After carefully marking the hole locations to
match the hole spacing in the pull, use a drill with a 3/32"diameter drill bit to drill a 1/2" deep hole. Brass screws require a little bit of
lubricant (a drop of liquid soap, a bit of bar soap, or candle wax). Use a screw driver to slowly install the wood screws and ensure the
screw driver does not slip. DO NOT USE A POWERED SCREW DRIVER.
WITH PREDRILLED HOLES: Hammer T-Nuts into existing holes on the interior of the drawer or door. If necessary the prongs
on the T-nuts can be bent flat with a pair of pliers. Do not use a screw to install T-Nuts. Choose a screw length which will not protrude
past the T-Nut. DO NOT USE A POWERED SCREW DRIVER.
BIN PULL: Carefully determine a desired knob location. After carefully marking the hole locations to match the hole spacing in the
pull, use a drill with a 3/16" diameter drill bit to make the hole through the drawer front or door. Choose a screw which protrudes
about 1/8" - 1/4" from the face of the drawer front or door. Use a screwdriver to tighten the screws while gently holding the drawer
pull. DO NOT USE A POWERED SCREWDRIVER.
CLEANING INSTRUCTIONS
1. Dust often using a clean, soft, dry and lint-free cloth.
2. Blot spills and wipe with a clean, damp cloth immediately
3. We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacqueredfinish.
4. Hardware may loosen over time. Periodically check to make sure all connections are tight. Re-tighten ifnecessary