WilTec XPOtool 63875 User manual

User’s Manual
Foldable Access Ramps
63875
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further
developments.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.

https://www.XPOtool.com Item 63875 Page 2
The Tool Experts
09 2022-1
The information contained in this document may alter at any time without prior notice. No part of this
document may be copied or otherwise duplicated without prior written consent. All rights reserved.
WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man-
ual, nor in the diagrams and illustrations shown.
Although WilTec Wildanger Technik GmbH has made every possible effort to ensure that this operating
manual is complete, accurate, and up-to-date, errors cannot be ruled out entirely.
If you have found an error or wish to suggest an improvement, we look forward to hearing from you.
Send us an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in our online shop:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler – Germany
To return your goods for exchange, repair, or other purposes, please use the following address. Atten-
tion! To allow for a trouble-free complaint or return, it is important to contact our customer service team
before returning your goods.
Retourenabteilung
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler – Germany
E-mail: [e-mail]
Tel: [phone]
Fax: [phone]

https://www.XPOtool.com Item 63875 Page 3
The Tool Experts
09 2022-1
Introduction
Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to
always take some basic safety precautions when using this product. Please read this operating manual
carefully and make sure that you understand it.
Keep these operation instructions in a safe place.
Safety instructions
•The ramps have been designed to make it easier for you to load or unload ATVs/quads, motor-
cycles, and lawn mowers. However, they are not meant to carry the weight of a vehicle with the
ramps being opened.
•Only drive a vehicle on the ramps when they are closed.
•Do not exceed the nominal load capacity of the ramps. Used for a vehicle (closed), one ramp
has a maximum load capacity of 800 kg. Used for an ATV/quad (opened), one ramp has a
maximum load capacity of 250 kg.
•Keep your fingers away from the foldable components when opening/closing the ramp. Risk of
injuries!
•The owner and/or user must read, understand, and follow all warnings, precautions, and instruc-
tions before using the product.
•Read, understand, and obey all instructions before operating the device. Do not use the ramps
without reading and understanding all instructions, precautions, and warnings first. Any im-
proper use can lead to material damage and/or personal injury.
•Only use the device on a hard, level surface when loading or unloading.
•Never exceed the maximum load capacity of the back door of your vehicle. Refer to the user’s
manual of your vehicle to find the correct value.
•Keep your extremities (hands, feet, etc.) away from the ramps. Neither reach under the ramps
nor stay under them.
•Every ramp seeming damaged, worn, or inoperable must immediately be put out of operation
until repair. It is recommended that you ask a qualified person to do the repair job.
•If you suppose that the ramps have been exposed to an unusual stress or shock, they must be
put out of operation until visual inspection.
•Do not place tools or other devices under the ramps.
•These ramps can only be used with the flange pointing downwards (see assembly instructions).
Using the ramp in reverse assembly direction with the flange pointing upwards (to guide the
wheels) considerably reduces the maximum load capacity.
•The ramps are designed to rest against the upper edge of the back door or trailer. If the loading
area is not coated, the ramps might scratch the protective paint surface of your vehicle.
•Never exceed the maximum height of 100 cm (40″) if using the ramps opened. Using the ramps
in their opened position at a height exceeding the recommended maximum height can lead to
damages of the charge and/or personal injuries.
•Make sure, before using the ramps, that the lorry or trailer is blocked and that the braked are
applied. Use chocks to block the wheels. In case the lorry or trailer moves forward when loading
or unloading, the ramps might slip off the vehicle, causing the charge to fall.
•Check the bent part of the ramps to make sure that it rests entirely on the rear end of the lorry
or trailer. Only use the ramps on a hard, level surface. Otherwise, a dangerous situation might
arise, provoking damages and/or injuries. Avoid wet slippery surfaces and surfaces with mac-
adam.
•Before charging, fix the ramps opened to the lorry using the safety chains.
•Do not drive the load onto the ramp opened. The load must be guided via the opened ramp by
hand.
•Due to potential risks linked to this type of devices, no modifications can be made to the product.
•Only attachments and/or adaptors supplied by the manufacturer may be used. Non-observance
of these instructions/warnings can lead to damages and/or injuries.
•Make sure that the load stays in the centre of the ramp and only use two ramps to load or unload
a vehicle. Non-observance of these instructions/warnings can lead to damages and/or injuries.

https://www.XPOtool.com Item 63875 Page 4
The Tool Experts
09 2022-1
•The ramps must not be used to support both ends at the same time or just one side of a vehicle
as you would do with mounting stands.
•The maximum wheel width is 9″.
•Do not use other lifting devices in combination with these ramps.
•Do not remove the brakes, the engine, parts of the gearing, the drive chain, drive shaft, Cardan
joints, or wheels with the vehicle being on the ramps.
•Make sure that the wheels used to move the vehicle onto the ramps are well aligned forwards
and stay in the centre of the ramps.
•Another person, who must not stay in the line of the vehicle, should observe and guide the driver
when loading or unloading via the ramps.
•Drive at low speed and with caution. Never accelerate or brake abruptly. Once the vehicle has
reached the top of the ramp, you should only apply the brakes to prevent going too far ahead.
•Put the vehicle in neutral and apply the parking brake firmly. The vehicle should not move when
the brakes are released. Put the vehicle in reverse or park and secure the wheels to the ground
with jack blocks.
•Make sure that both wheels are correctly placed on the access ramp. Slightly joggle the vehicle
from one side to the other and in the direction of movement to make sure that both the vehicle
and ramps are stable, and make sure that you are not staying within the danger zone. Make
sure that the ramps have not been damaged or bent during charging.
Parts list
Before assembling the device, check if all components are present.
№
Name
Quantity
1
Foldable ramp carrying strap
2
2
Bent piece of ramp with safety chains
2
3
Wheel stop
2
4
Screw and nut (M10×20)
8
5
Screw, nut, and washer (M8×35)
4
6
Screw, nut, and washer (M8×20)
4
7
Screw and washer (M8×16)
4
8
Screw, nut, and washer (M6×16)
2
Tool required for assembly: 13 mm half-moon wrench

https://www.XPOtool.com Item 63875 Page 5
The Tool Experts
09 2022-1
Assembly
Warning! Only assembly the device according to the illustrations. Do not assemble the device with the
flange pointing upwards. The flange pointing downwards is meant to stabilise the ramp; it is not meant
to guide the wheels.
Right
Bad
Notes
•Load and unload your equipment with caution.
•The load must be centred between the sides of the ramps.
•The surface of the ramp must be dry, clean, and free from oil and grease.
•When loading or unloading a vehicle, make sure that the engine is off.
Step 1: Use the handle to take the ramp out of its
package.
Step 2: Open the first portion of the ramp and
screw the pent piece using 4 screws per ramp.

https://www.XPOtool.com Item 63875 Page 6
The Tool Experts
09 2022-1
Step 3
To use the product for lorries, remove the stop inside the closed portion and install it to the end of the
ramp as shown.
Step 4
To use the product for ATVs/quads, remove the stop and open the 2 parts as shown.
Secure the ramps to the loading area using the safety chains.

https://www.XPOtool.com Item 63875 Page 7
The Tool Experts
09 2022-1
Maintenance and inspection
•These ramps must be maintained following the instructions. Every ramp must be checked before
use. The ramps must not be used if they are somehow damaged.
•Before use, visually inspect the ramps to find potential cracks, bends, loose or missing parts, or
rust.
•Clean all surfaces and keep all stickers, warnings, and instructions in good condition.
•Always keep the surfaces of the ramps clean, dry, and free from oil and grease.
Important Note:
Reproduction and any commercial use (of parts) of this operating manual, requires a written permission
of WilTec Wildanger Technik GmbH.