Raptor Series 1301-0151 User manual

1301-0151
RUNNING BOARD
1. Remove all contents from the package and check stainless steel running boards for any damage. Also,
verify that all components and hardware listed above are included before you begin installation.
2. Read installation manual and installation drawing completely. Understand all
brackets and bolts before installation.
1
Components:
Driver Side Running Board
Qty. 1
Passenger Side Running Board
Qty. 1
Front Bracket
Qty 2
Center Bracket
Qty 2
Hardware:
M10 Flat
Washers
Qty 30
M10 Lock
Washers
Qty 12
M8 x 30 MM
Hex Head Bolts
Qty 2
Tools Required:
Torque Specifications:
For Cab Mount Installations
Cab mount bolts are torqued to 70 Ft Lbs. All other M8 through M12 sized bolts/nuts are set to 15-20 ft lbs.
Note: When installing the brackets and bars, all hardware must be left loose until all the items are attached.
M10 x 30 MM
Hex Head Bolts
Qty 6
Rear Bracket
Qty 2
Rear Bracket
Mount
Qty 2
M10 Hex Head
Nut
Qty 24
M8 Hex Head
Nut
Qty 2
Load Reaction
Studs
Qty 6
Rubber Block
Qty 6
M5 Hex Head
Nut
Qty 12
M8 Flat
Washers
Qty 4
M8 Lock
Washers
Qty 2
M5 Button
Head Bolt
Qty 12
RATCHET TORQUE
WRENCH 17MM SOCKET 14MM SOCKET
L Bracket
(Used On
1500 Model Only)
Spacer Washer
Qty 12
Rev 2
1301-0151

3. Begin installation on driver side. Position
drivers side Front Bracket, Center Bracket
and Rear Bracket as shown along driver side.
Assemble the Load Reaction Studs as follows:
4a. On the short threaded end of the Load
Reaction Stud, install a M10 Hex Head Nut, a
M10 Flat Washer to the bottom of thread,
then install a Rubber Block tight up against
the M10 Washer and the M10 Hex Head Nut.
(The end of the Stud must be recessed in the
rubber washer approximately 3/16").
4b. On the long threaded end of the Load
Reaction Stud, install a M10 Flat Washer, a
M10 Lock Washer and a M10 Hex Head Nut to
the bottom of the threads.
NOTE: IF MOUNTING THE RUNNING BOARD
ON A 1500 MODEL TRUCK. YOU MUST
ATTACH L BRACKET TO FRONT BRACKET
IN ORDER TO USE THE LOAD REACTION
STUD.
5. Remove the factory front, center and rear
cab mount bolts and install the mount brack-
ets and running board per following instruc-
tion.
6. Install the Brackets to the Cab Mounts as
shown. Hand tighten, until the Load Reaction
Stud and the Running Board has been
installed. When installing on 2015-Current HD,
use 2 spacer washers between factory bush-
ing and mounting bracket.
7. Attach the load reaction stud assemblies
to the mounting brackets as shown. Insert
the stud from what will be in the inboard or
frame side thru the lowest hole in the bent
flange of the bracket that will allow the
rubber washer to seat firm against the side
wall of the frame. Install a M10 flat washer, a
M10 lock washer and a M10 Hex Head Nut
(Hand tight only)
8. Attach the Running Board to the Frnot,
Center and Rear Brackets using M5 Button
Head Bolts and M5 Hex Head Nuts.
9. Repeat these steps for passenger side
installation. When all hardware is in place,
everything must be tightened. See Page 1 for
Torque Specifications.
Driver Side
3
2
Rev 2
1301-0151

Driver Side
3
M8 X 30MM HEX HEAD BOLTS
M8 FLAT WASHER
L BRACKET
USED ON 1500 MODEL ONLY
LOAD REACTION STUD
RUBBER BLOCK
M10 LOCK WASHER
M10 FLAT WASHERS
M10 HEX HEAD NUT
POSITION RUBBER BLOCK
AGAINST SIDE OF FRAME
M5 BUTTON HEAD BOLT
L BRACKET
FRONT
BRACKET
CENTER
BRACKET
REAR BRACKET
REAR BRACKET
MOUNT
USE THESE
HOLES LOCATIONS
M5 HEX HEAD NUT
CAB
MOUNT
BOLT
CAB
MOUNT
BOLT
EXISTING BODY MOUNT BUSHING
SPACER WASHERS
M10 X 30MM HEX HEAD BOLTS
M10 LOCK WASHER
M10 FLAT WASHERS
M10 HEX HEAD NUT
M8 LOCK WASHER
M8 FLAT WASHER
M8 HEX HEAD NUT
CAB
MOUNT
BOLT
Rev 2
1301-0151
FOR 2015-CURRENT
HD ONLY