WilTec GT1507 User manual

Instruction manual
Spreader GT1507
60910
Illustration similar, may vary depending on model
Please read and follow the operating instructions and safety information prior to initial operation.
Technical changes reserved!
Illustrations, functional steps and technical data may deviate insignificantly due to continuous further
developments.

© by WilTec Wildanger Technik GmbH Item 60910 Page 2
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
The information contained in this document may alter at any time without prior notice. No part of this
document may be copied or otherwise duplicated without prior written consent. All rights reserved.
WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man-
ual, nor in the diagrams and illustrations shown.
Although WilTec Wildanger Technik GmbH has made every possible effort to ensure that this operating
manual is complete, accurate and up-to-date, errors cannot be ruled out entirely.
If you have found an error or wish to suggest an improvement, we look forward to hearing from you.
Send us an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in our online shop:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler Germany
Do you wish to collect your goods? Our address for collection is:
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler Germany
In order to shorten the waiting time and to allow for an easy on-site processing, we kindly ask you to
contact us briefly beforehand or to place your order via the webshop.
E-mail: [e-mail]
Phone: [phone]
Fax: [phone]
To return your goods for exchange, repair or other purposes, please use the following address. Atten-
tion! To allow for a trouble-free complaint or return, it is important to contact our customer service team
before returning your goods.
Retourenabteilung
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler Germany
E-mail: [email protected]o
Phone: [phone]
Fax: [phone])

© by WilTec Wildanger Technik GmbH Item 60910 Page 3
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
Introduction
Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to
always take some basic safety precautions when using this product. Please read this operating manual
carefully and make sure that you understand it.
Keep these operation instructions in a safe place.
Safety instructions
Before assembly read the safety instructions and the notes!
•Read the safety instructions for tractor owners and tractors. Familiarize yourself with the oper-
ation of your tractor before using the spreader.
•Read all the information and safety instructions for handling the chemicals to be broadcast.
•Always wear eye and hand protection while handling and broadcasting lawn or garden chemi-
cals.
•Never operate the tractor or spreader without wearing solid shoes, and do not let anyone ride
or sit on the spreader.
•Never let children operate the tractor or spreader, and do not allow any adult to operate them
without prior instruction.
•Always begin with the first (lowest) gear and with a low rotation and gradually increase the
rotation if conditions allow to do so.
•When towing the spreader, do not get too close to a beck or ditch and look out for potholes and
other dangers that might lead to loss of control of the spreader or tractor.
•Before operating a vehicle on a slope (hill), you must respect the safety instructions of the user’s
manual of the vehicle concerning safety on slopes. Do not drive on steep slopes!
Open the packaging and pouch, remove all parts and check for completeness.

© by WilTec Wildanger Technik GmbH Item 60910 Page 4
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
№
Designation
Qty.
№
Designation
Qty.
1
Bolt M6×60
2
7
Counter nut M5
1
2
Bolt M6×40
8
8
Big washer ⌀6
4
3
Bolt M6×35
4
9
Washer ⌀16
1
4
Hexagon socket screw
1
10
End cap
2
5
Fillister head screw M4×20
1
11
Inner axle-bearing
2
6
Counter nut M6
12
12
R pin
1
Assembly instructions
1st step:
1. Mount the driving wheel (1) onto the drive and axle construction (3).
2. Insert the M4×20 fillister head screw (2) through the driving wheel and axle.

© by WilTec Wildanger Technik GmbH Item 60910 Page 5
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
2nd step:
1. Fix the wheel frame construction on either side of the driving axle and connecting rod.
2. Insert two M6×40 screws through the wheel frame into the connecting rod. Make sure that the
hole on the driving axle is on the right as shown.
3. Fix the mounting frame and foot to the hopper with M6×40 screws, M6 counter nuts and big
washers ⌀6.
Note: The screws and nuts do not need to be tightened yet.

© by WilTec Wildanger Technik GmbH Item 60910 Page 6
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
3rd step:
1. Mount one end of the connecting plate (5) to the wheel frame with a M6×35 screw (4) and M6
counter nut (3).
2. Then mount the connecting rod to the wheel frame with a M6×60 screw (7) and M6 counter nut
and fix the connecting plate to the connecting rod (1) with a M6×35 screw (6).
Note: The screws and nuts do not need to be tightened.

© by WilTec Wildanger Technik GmbH Item 60910 Page 7
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
4th step:
1. Set in the inner axle box into the outer axle box, making sure that they are securely seated.
2. Mount the right wheel construction to the right axle with the M5×45 hexagon socket screw and
M5 counter nut, then mount the end cap on the right axle with a wooden or rubber mallet.
3. Now mount the left wheel construction to the left axle inserting a ⌀16 washer, and mount the
end cap on the left axle with a wooden or rubber mallet.

© by WilTec Wildanger Technik GmbH Item 60910 Page 8
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
5th step:
1. Assemble the hopper part (5) and tube part (3) construction with a M6×40 screw (1) and M6
counter nut (4).
2. Now tighten all screws and bolts mounted from the first step on, but do not tighten them too
strongly, then insert the R pin (2) to the front end for securing.

© by WilTec Wildanger Technik GmbH Item 60910 Page 9
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
6th step: adjustments
After having finished the above-mentioned steps, the following steps do not need to be followed. They
are necessary in case the individual parts do not properly match. To operate this spreader, push the
handle up. You can shift the position of the wing nut on the pressure gauge and lever to adjust the
spacer of the three holes between the hopper and adjustable plate according to your needs.

© by WilTec Wildanger Technik GmbH Item 60910 Page 10
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
Exploded view