Winco 3170 User manual

Page 1 of 5
006250 Rev N Date 06-26-13 JWC
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
If you have trouble understanding these instructions contact your dealer or Winco customer support, [phone],
e-mail: [email protected] before attempting to use this product; otherwise injury may occur.
Winco assumes no responsibility for damage or injury caused by the improper
assembly, installation or use of these products.
1. READ AND FOLLOW ALL DIRECTIONS.
2. NEVER place screen on a cart, table, stand or other objects; Screen could fall and INJURY MAY OCCUR.
3. NEVER place screen near open flame or over a radiator or heat register.
4. NEVER place screen in front of a door or exit sign; or during emergency screen could hinder evacuation.
5. SUFFOCATION DANGER to children if vinyl is not attached to screen; Screen could block nose and
mouth
and prevent breathing. VINYL SCREEN IS NOT A TOY.
6. DO NOT allow children to play with screen; Screen could fall and INJURY MAY OCCUR.
7. Screen should ALWAYS be positioned on level surface. 8. NEVER stand or ride on screen legs; INJURY
MAY OCCUR.
9. DO NOT use screen in or with ANY type of vehicle or trailer.
10. DO NOT attach objects to screen frame; Screen can tip over and INJURY MAY OCCUR.
11. Remove from service; Any screen with broken or missing parts, torn vinyl, or other visible damage.
12. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.
13. SAVE THESE INSTRUCTIONS for future reference and training.
Tools needed:
•Scissors or box cutter
•5/32 Allen Wrench (provided)
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY
1. After checking your product for any shipping damage, remove all packing material and hardware that was
secured for shipping. Cut tape and/or plastic with scissors, being careful not to damage screen.
LEG INSTALLATION SEE PHOTOS, NEXT PAGE
2. Insert both Leg Frame Assemblies (#3) into the bottom of the Wing/Mid Frame Assembly (#1A). Line up the
holes in (#3) w/ the holes in (#1A).
3. Using the Allen Wrench provided screw in 1-Button Socket Screw (3D), per leg, through (#1A) and into (#3)
3170
Designer Three Panel Screen
CUSTOMER INSTRUCTIONS

Page 2 of 5
006250 Rev N Date 06-26-13 JWC
PANEL REPLACEMENT SEE PHOTOS, NEXT PAGE
4. To replace Vinyl Panels (#4), hold the screen by the top Screen Rod (#2A).
5. Next, using the Allen Wrench provided, push in on the small hole just below the Snap Button (#2B). Re-install
(#2A) by repeating the above procedure, then release (#2B) when (#2A) is in place
CARE & MAINTENANCE OF YOUR SCREEN
6. Periodically check all fasteners for tightness.
7. To clean Vinyl Panels use only mild liquid soap and water.
Wrinkles in Vinyl –Storage and/or shipping causes wrinkles in the vinyl of your Winco Screen; This is normal. Please allow 1-
2 weeks at room temperature (approx. 70+ degrees) to allow for vinyl to return to original appearance.
(1A) Wing/Mid Frame Assembly Kit 1
(1B) Domed Plastic Insert 10
(2B) Snap Buttons 4
(3D) ¾” Button Socket Screw 2
(2A) Screen Rod 6
(2B) Snap Buttons 12
(3) Leg Frame Assembly 2
(3B) 2” Caster 4
(3C) Caster Insert 4
(3D) ¾” Button Socket Screw 2
Items Included with Screen:
Qty.

Page 3 of 5
006250 Rev N Date 06-26-13 JWC
(4) 3170 Vinyl Panel 3
Visit our website www.wincomfg.com/product-documents/parts-lists for a complete parts list catalog of your chair or
call Customer Service @ 1-800-237-3377 to request it by mail.
Other Quality Winco Medical Furnishings You May Be Interested In:

Page 4 of 5
006250 Rev N Date 06-26-13 JWC
Visit us online at www.wincomfg.com

Page 5 of 5
006250 Rev N Date 06-26-13 JWC
Design, appearance, parts, & construction are subject to change without notice