Windsor 1390 User manual

0800 607 028
[e-mail]
FITTING INSTRUCTIONS
TOUCHPAD ELECTRONIC DEADBOLT LOCK
© WINDSOR ARCHITECTURAL HARDWARE
Version 1
windsorhardware.co.nz
Package Contents
Installation To view an easy to follow how-to video for installing this product visit windsorhardware.co.nz/installation
Screws
Part Description Quantity
A Key 2
B Cylinder 1
C Deadbolt Touchpad 1
D Deadbolt Latch 1
E Striker Plate 1
F Mounting Plate 1
G Receiver 1
H Battery Cover 1
I Drive-in Sleeve 1
1. Adjust the latch to the desired
backset (60mm or 70mm).
Backset is the distance from the
door edge to the centre of the
hole on the door face.
To adjust the latch to the 70mm
backset, rotate the latch until it
stops. Reverse the direction to
return to the 60mm backset.
3. Establish the height and backset
for the lock on the door.
5. Use the marks as a guide for drilling a
25mm (1") diameter hole through the
door edge to a depth of at least 90mm.
Ensure this hole is square to the door.
Then drill a 54mm diameter hole
through the door face for the lockset.
We recommend using a 54mm hole
saw. For clean cut-outs, drill from both
sides, meeting in the middle of the door.
6. Insert the latch, scribe around
the faceplate, remove, then
chisel out 4mm deep recess to
enable the latch faceplate to sit
flush with the door edge.
2. Determine which latch mounting
method will be used (square plate
or drive-in) and make the
necessary adjustments.
No adjustments are required for
the square latch face plate.
a. Use a flat screwdriver to
separate the face plate.
b. Align the drive-in sleeve and
snap it into the latch case.
B
a
c
k
s
et
4. Use the template provided as an
indication to mark the centre of
the circle on the door face and
the centre of the door edge.
7. Remove any loose saw dust, insert
the latch and secure it with the two
wood screws provided. Make sure the
cross is on the bottom of the latch.
Please do not fully tighten the screws
until the lock is completely installed.
For the drive-in latch, drive the latch
into the hole on the edge of the door.
Product code: 1390

© WINDSOR ARCHITECTURAL HARDWARE
Version 1
8. Close the door against the frame
and mark the latch position for
fitting of the striker.
9. Measure one half of the door
thickness from the door stop and
vertically mark the centre line of
the striker. Drill a 25mm (1")
diameter hole, 25mm (1") deep
at intersection of the horizontal
and vertical lines. Chisel out a
2mm deep recess along the
striker outline to allow the striker
to sit flush against the doorframe.
Secure the striker with the wood
screws provided.
10. Install the cylinder into the
deadbolt keypad with the tail
piece in horizontal position
inserted through the hub of the
latch.
12. Pass the IC wire through the
wire hole of the mounting plate
on the interior side of the door.
Fix the mounting plate with
screws onto the door face.
Make sure the deadbolt keypad
on the outside is straight.
13. Insert 4 (AA) 1.5 V alkaline
batteries and slide the battery
cover onto the receiver module.
Notes:
(1) Alkaline batteries are
recommended in order to
stabilise the power supply. If
you do not use alkaline, battery
performance will be reduced
greatly.
(2) All settings will be retained
in the memory even if the
batteries are completely dead.
PRINT AT 100% SCALE
11. Pass the IC wire under the latch
to the interior side of the door
and insert the tail piece through
the cross-shaped crank of the
latch.
0800 607 028
[e-mail]
FITTING INSTRUCTIONS
windsorhardware.co.nz
TOUCHPAD ELECTRONIC DEADBOLT LOCK Product code: 1390