Windster UK-611 Installation instructions

RANGE HOOD (HOOD FANS)
INSTALLATION & OPERATING MANUAl
o
UK-611
PLEASE READ CAREFULLY AND UNDERSTAND THIS MANUAL
BEFORE INSTALLING AND OPERATING THE RANGE HOOD

COOKER HOOD
Dear Client
For fulfilling the best efficiency of the range hood, please read the manual carefully before installatimlOd
operation Please note this appliance must be installed and serviced by a licensed electrician.
GENERAL INDICATION
Before installing and using the hood, please be sure that the voltage(V) and the frequency(Hz) marked
on the feature plate is in accordance with the voltage and frequency in your area. The feature plate
and technical date are shown on the side of the product.
TECHNICAL CHARACTERISTICS
Model NO:UK-611
Single speed motor:77W
Halogen Light Bulb:2x IOW
Voltage: IlO/120V
Frequency:60HZ
Filter:S/S Pyramidal Filter
Control:Push Button
INSTALLATION
PLEASE WEAR "SAFETY GLOVES" BEFORE INSTALLATION, CLEANING,
LIGHT BULB CHANGING AND DISMANTLING.
The hood should be installed as suction machine and connected the plastic columnar outlet piece
supplied with the hood( 150mm diameter) to an exhaust pipe connected directly to the outside.
We recommend you should use the 150mm diameter pipe for better performance and lower noise levels
NOTE:Please never connect the hood to chimneys, ventilation pipes or hot air pipes.
Before connecting any pipes, you need to consult municipal ordinances and request the permission fron
the people in charge of the building. A good and adequate ventilation is important.
WALL MOUNTING
The accessory is needed to install at the side of the hood. The hood must be installed at a minimum
distance of 65CM from the strove top.
Place the installation ho<;>kin the location where the hood is mounted.
Drill holes into the wall by using 8mm drill bit.
The accessory bag includes the installtion hook and screws.
NOTE: If any problems or damages with the Range Hood, please must let a professional and qualified
person to repair the problems. If there were not normal installation or normal use, the manufacturer Iimporter
Iwholesaler will not hold any responsibilities for any damages, personal property, real estate and bodily
injures.
No matter if it is caused directly or indirectly by the Range Hood.
ASSEMBLY OF DECORATIVE EXTENDIBLE DUCT
Duct A and duct B are connected to hood body. Loose Screws C&D, extend duct B to Ft for your height of
telescopic Duct (Fig. I)
B

CONTROL PANEL
This panel is located on the front of the hood.
I.Push button oflight (Fig. 2, Ref A)
2.Push button of motors (High speed, low speed) (Fig 2, RefB, C)
3.Push button of motor-off (Fig. 2, Ref D)
ABC D
I. . . . I
o 0 0 0
o '" ~ 0
Fig.2
MAINTENANCE CLEANING
Before any type of operation, make sure that the electrical cord is isolated and the switch is off.
Clean the cooker hoods with mild, liquid detergent and using abrasive cleaning is prohibited.
Light Bulb Replacement:
Switch off the power and remove the light cover from the underside of the range hood.
Replace the light Bulb with a halogen light bulb (lOW)
CLEANING THE GREASE FILTER
The grease filters should be rinsed with hot water at least once a month.
After rinsing and drying, place the grease filter in a dry space.
IMPORTANT
Because grease can lead to overheat and catch fire, please never leave frying food unattended.
To reduce the risk of bodily injuries, please wear "Safety Gloves" for installation, cleaning, light bull
changing and dismantling.
IROUI!LE~HOOIING GUIDE
2
PROBLEM SOLUTION
No electric power 1. Check the plug and socket
2 .Check the wires.
The bulb does not light. I.Check whether the bulb is broken.
2.Check whether the switch is damaged
1. Check whether the switch of the motor
The motor does not rotate. is damaged.
2. Replace the motor if the switch is
not damaged.
The Range Hood vibrates Check whether the blower is damaged.
during Operation Replace the damaged blower.

Model: UK-611
1--.,--+- +--E:B--I
Hook hole 182mm
~
~
c
""
l"-
I
L{
I"-
""
E
E
L()
~
-::t
900mm
CIRCUIT DIAGRAM
LOW SPEED
HIGH SPEED
UGHT SWITCH
3
,1-WIRE CONNECTOR
W-WHITE
R-RED
Y- YELLOW
G-GREY
B-BLUE
GR - GREEN
OG-ORANGE
BK-BLACK
DR. BROWN
W GR BK
nE~CTRICPLUG
~IlOV/60Hz

SAFETY NOTES
I. All electrical work must be done in accordance with local and/or national electrical code as
applicable for safety. This product must be grounded if you are unfamiliar with methods of
installing electrical wiring, secure the services of a qualified electrician.
2. Turn off power at service entrance before installing wiring or servicing this product.
3. Turn off power to avoid risk offire electric shock or injury to person for cleaning and users
maintenance such as lubrication.
4. Toavoid motor bearing damage and noise and/or unbalanced impellers keep drywall spray
construction dust etc. off power unit.
5. Fireplaces, gas furnaces, water heaters, and the like require proper flow of combustion air and
exhaust. Make sure this flow is not altered when using any exhaust fan.
6. Please read specification label onproduct for further information and requirements
CAUTION: Toreduce the risk offire and to properly exhaust air, be sure to duct air outside. Dc
not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces or garages.
Please wear "Safety Gloves" for installation, cleaning,
light bulb changing,dismanting. To reduce the risk of
any bodily injuries.
SAFETY NOTES
~orkzna~
'V
illJJi
1Q,;
ttJ' 0l.
&.rJ ~
CAUTION