WineEnthusiast 269 02 40 03 User manual

Classic Stainless Beverage Cooler
269 02 40 03
INSTRUCTION MANUAL
PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING AND OPERATING.
1

TABLE OF CONTENTS
Contents ____________________Page #
Beverage cooler Package Contents 3
Important Safety & Pre-Use Instructions 3
Installation Instructions 3
Built In Installation 4
Reversing Door Swing 4
Operating Your Beverage cooler 4
Temperature Settings 4
Layout & Storage 5
Care & Maintenance 5
Troubleshooting Guide 6
Technical Information 7
Warranty Information 7
2

Beverage cooler Package Contents
•Instruction manual
•3 Standard Shelves
IMPORTANT SAFETY INSTRUCTIONS
WARNING To reduce the risk of fire, electrical shock, or injury when
using your appliance, follow these basic precautions:
Read all instructions before using the beverage cooler.
DANGER: Risk of child becoming trapped in new cellar, old beverage cooler/refrigeration unit, or large boxes.
Junked or abandoned appliances, boxes and other containers are still dangerous, even if they will “just sit in
the garage for a few days”.
Before you throw away your old beverage cooler or refrigeration unit: 1. Take off the door. 2. Leave the
shelves in place so that children cannot climb inside.
Never allow children to operate, play with, or crawl inside the appliance.
Never clean appliance parts with flammable fluids. The fumes can create a fire hazard or explosion.
Do not store in the vicinity of any other appliance. Do not store near gasoline or any other flammable vapors.
The fumes can create a fire hazard or explosion.
-Save these instructions-
BEFORE USING YOUR BEVERAGE COOLER
Remove the exterior and interior packaging.
Before connecting the beverage cooler to the power source, let it stand upright for approximately 2 hours.
This will reduce the possibility of a malfunction in the cooling system from handling during transportation.
Clean the interior surface with lukewarm water using a soft cloth.
INSTALLATION INSTRUCTIONS
General Installation Instructions
This appliance is designed for free standing installation. Do not build-in or recess into closed cabinetry.
Place your beverage cooler on a flat, solid floor that is strong enough to support it when it is fully loaded. To
level your beverage cooler, adjust the front leveling leg at the bottom of the beverage cooler.
When moving your beverage cooler, please do not incline it more than 45 degrees.
Locate the beverage cooler away from direct sunlight and sources of heat (stove, heater, radiator, etc.).
Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption.
Extreme cold ambient temperatures may also cause the unit to perform improperly.
Avoid locating the unit in damp areas.
Plug the beverage cooler into a dedicated (for this appliance only), properly installed and grounded wall
outlet. Do not under any circumstances cut or remove the third (grounding) prong from the power cord.
Any questions concerning power and/or electrical grounding should be directed to a certified electrician or
authorized product service center.
3

Built In Application.
Your beverage cooler can be installed built into cabinetry. The minimum dimensions of the built in area are as follows:
24 ½” W X 26 ½” D X 33 ¼” H
Door Swing
Your beverage cooler was shipped from the factory with the door opening from left to right. If necessary, you can
reverse the door opening direction from right to left by following these steps:
1. Remove the lower hinge by removing the screws holding the door in place.
2. Slide the door off the bottom hinge and slide away from the upper hinge.
3. Loosen and remove the screws holding the upper hinge in place.
4. Your beverage cooler included an alternate set of hinges. Remove those from your instruction packet.
5. Turn the door upside down so that the handle is on the proper side.
6. Attach the top hinge to the left side of the beverage cooler then slide the door into place.
7. Attach the bottom hinge and secure door in place.
Operating Your Beverage cooler
Setting the Temperature Control/Display panel
Temperature Control
Control Panel
Turns the appliance ON or OFF
Turns the light ON or OFF.
Increases the temperature by 1°C or 1°F.
Decreases the temperature by 1°C or 1°F.
The temperature display can be shown in either Fahrenheit or Celsius. To change the temperature display
press and hold for 5 seconds.
4

SETTING A TEMPERATURE
Press or to increase or decrease the temperature.
LAYOUT AND STORAGE
Your cabinet was designed to store a maximum number of bottles and cans securely. We recommend that you
observe the tips below to optimize loading.
•Remove tape from shelves once unit is stable and ready for storage.
•Disperse the bottles and cans evenly to avoid concentrating weight in one place. Bottles must not touch either
the back of the cabinet.
•Make sure that bottles and cans are not all grouped together either at the top or bottom of the cabinet.
•Only pull out one shelf at a time. Never attempt to pull more than one.
•Maximum weight capacity per shelf is 55 lbs.
CARE AND MAINTENANCE
Cleaning Your Beverage Cooler.
Turn off the power, unplug the appliance, and remove all items including all shelves.
Wash the inside surfaces with a solution of warm water and baking soda (approximately 2 tablespoons of baking
soda for each quart of water.)
Wash the shelves with a mild detergent solution.
Wring excess water out of the sponge or cloth when cleaning area of the controls, or any electrical parts.
Wash the outside of the cabinet with warm water and mild liquid detergent. Rinse well and wipe dry with a clean soft
cloth.
Vacuum the front grill and back of the unit twice yearly. Make sure the power is off before cleaning.
It is recommended to clean the unit completely inside and out once a year to maximize the longevity of the beverage
cooler.
Power Loss
Power failures that are corrected within a few hours should not affect the temperature of your appliance if you
minimize the number of times the door is opened. If the power is going to be off for a longer period of time, you need
to take other measures to protect your contents.
If the unit is unplugged, loses power, or is turned off, you must wait 3 to 5 minutes before restarting. Attempting to
restart the beverage cooler before this time has elapsed may prevent the beverage cooler from starting.
Absence/Vacation
Short vacations: You may leave the beverage cooler powered on and unattended for absences of less than three
(3) weeks.
Long vacations: If the appliance will not be used for more than three weeks, remove all items and turn off the
appliance. Clean and dry the interior thoroughly. To prevent mold growth, leave the door open slightly, blocking it
open if necessary
5

Moving Your Beverage cooler
Remove all items.
Securely tape down all loose items (shelves) inside your appliance.
Turn the adjustable leg up to the base to avoid damage.
Tape the door shut.
Be sure the appliance stays secure in the upright position during transportation. Also protect the outside of the
appliance with a blanket or similar item.
Energy saving Tip
The beverage cooler should be located in the coolest area of the room, away from heat producing appliances, and
away from direct sunlight.
TROUBLESHOOTING GUIDE
Many common issues with your beverage cooler can be solved very easily. Try the troubleshooting tips below
should you experience any problems.
PROBLEM POSSIBLE CAUSE
Beverage cooler does not operate. Not plugged in.
The appliance is turned off.
The circuit breaker tripped or a fuse has blown out.
Beverage cooler is not cold enough. Check the temperature control setting.
External environment may require a higher setting. (e.g. room
needs to be air conditioned)
The door is opened too often.
The door is not closed completely.
The door gasket is not sealing properly.
Beverage cooler is turning on and off frequently. The room temperature is hotter than normal.
The door is opened too often.
The door is not closed completely.
The temperature control is not set correctly.
The door gasket does not seal properly.
The light does not work. Not plugged in.
The circuit breaker tripped or a fuse has blown.
The light bulb has burned out.
The light button is “OFF”.
Vibrations. Check to assure that the beverage cooler is on a level
surface.
The beverage cooler seems to make too much noise. A faint humming noise may come from the flow of refrigerant,
which is normal.
As each cycle ends, you may hear gurgling sounds caused by
the flow of refrigerator in your beverage cooler.
Contraction and expansion of the inside walls may cause
popping and crackling noises.
The beverage cooler is not on a level surface.
The door will not close properly. The beverage cooler is not on a level surface.
The door was reversed and not properly installed.
The gasket is dirty.
The shelves are out of position.
6

TECHNICAL DATA
WARRANTY INFORMATION LIMITED WARRANTY
Length of Warranty: This Limited Warranty lasts for one (1) year from date of receipt of purchase of the beverage
cooler (“Limited Warranty Period”). Extended warranties may be available for an additional cost at the time of purchase
or up to the seventh month from date of purchase. These extended warranties would extend this one (1) year limited
warranty to two (2), three (3), or five (5) years. Details about our extended protection plans can be found @
wineenthusiast.com.
Who is Protected: This Limited Warranty protects the original purchaser during the Limited Warranty Period, provided
that such purchaser can present appropriate proof of original purchase.
What is Covered: This Limited Warranty covers any defects in workmanship or materials in your new beverage cooler
under normal use.
What is Not Covered: The following are not covered by this Limited Warranty damage due to such things as accident,
misuse, abuse, mishandling, neglect, unauthorized repair, failure to properly maintain, acts of God or any other cause
beyond the reasonable control of the Wine Enthusiast whether similar or dissimilar to the foregoing.
Purchaser understands and acknowledges that the beverage cooler is a wine refrigerator, which houses wine.
Purchaser assumes all the risk of using these units, including risk of spoilage, humidity variations, temperature variations,
leaks, fires, water damage, mold, mildew, dryness and similar perils that may occur.
Item Number 269 02 40 03
Accommodation
(bottles) 150, 12 oz cans
Beverage cooler Dimension 23 ½” W X 24 ½” D X 32 1/4” H
Type of cooling Compressor cooling
Climate type N
Electricity protection grade I
Nominal voltage/Frequency 115V/60HZ
Rated power(W) 120 Watts
Ambient temperature 60-77 degrees Fahrenheit
Temperature range
34-43 F
Range of inside cabinet humidity 60%RH
7

What We Will Do: During the Limited Warranty Period, Wine Enthusiast and/or the manufacturer will, at its sole
discretion, repair or replace any beverage cooler not operating within the manufacturer’s specifications. All costs for
labor and materials thereto shall be covered during the Limited Warranty Period. If Wine Enthusiast deems the
beverage cooler is not repairable, Wine Enthusiast will use the value of your original order toward a replacement;
provided, however, that the purchaser will be responsible for all shipping and handling costs with respect to the
replacement after the initial ninety (90) days after the date of receipt of original purchase. After the initial ninety (90)
day period after the date of receipt of purchase, purchaser must pay any shipping and handling charges that are
incurred in shipping or transporting the beverage cooler for service under this Limited Warranty. Wine
Enthusiast reserves the right to substitute materials of substantially similar quality in the event that identical materials are
not available at the time the Limited Warranty services are performed. Wine Enthusiast reserves the right to request
that purchaser contact a local refrigeration company to service the beverage cooler.
How to get Warranty Service:In the event your beverage cooler is not operating within the manufacturer’s
specifications, during the Warranty Period, contact customer service by email at [e-mail] or by
phone [phone].
Limitation of Implied Warranties: All implied warranties, including warranties of merchantability and fitness for a
particular purpose, are limited in duration to the length of this Limited Warranty.
Exclusion of Certain Damages: Wine Enthusiast’s liability is limited to replacement or repair of the defective beverage
cooler. Wine Enthusiast shall not be liable for any damages, whether incidental, consequential or otherwise, because of
any defective beverage cooler.
How State Law Applies: Some states do not allow limitations on how long an implied warranty lasts and/or do not
allow the exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply to
you.
The Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
8