Winegard AIR 360+ User manual

OMNIDIRECTIONAL TV/FM ANTENNA
+ WIFI + 4G EXTENDER*
*WiFi & 4G functionality requires Winegard®Gateway™(GW-1000) sold separately
Model AR-360B
Register your product at www.winegard.com/myantenna
2452440
Rev0 7-19
Plus!
Internet ready
Requires Winegard Gateway router
WINEGARD
®
AIR™360+
www.winegard.com/air-360-plus
Manuel disponible en français au www.winegard.com

–1–
Welcome
Thank you for purchasing the Winegard®Air™360+and trusting Winegard to
bring connectivity solutions to you while on the go. This product, combined
with the Winegard®Gateway™will provide you more freedom when choosing
where to adventure, all while bringing the comforts of TV and secure internet
to you and your devices.
Before installing or operating please read these instructions completely and
carefully. Failure to follow these instructions could cause damage to the
product and/or RV.
If you have any questions or need help, email [email protected] or call
1-800-320-9992.
Contents
Welcome.....................................................................................1
Contents .....................................................................................1
Specifications/Features ................................................................2
Parts Included.............................................................................2
Product Information.....................................................................3
Installation Instructions................................................................4
TV Antenna Operation ................................................................10
Troubleshooting .........................................................................12
Warranty Statement ...................................................................13
Disclaimer
Although every effort has been made to ensure that the information in this manual is correct and
complete, no company shall be held liable for any errors or omissions in this manual. Changes
and technological advances are continuously being made in the over-the-air and wireless market.
Information provided in this manual was accurate at time of printing. If the Winegard Air 360+
or Gateway do not function as expected, please contact Winegard Company at 1-800-320-9992,
email [email protected], or visit our website at www.winegard.com.

Prewire
hole cover
Barrel crimp
splice
Power switch
into wall plate
Terminal
insulator (2)
Mounting
screw (10)
Coax to audio
cable
20'Coax
cable
10'Power
cable
Winegard
antenna power
supply/wall plate
w/hardware
Wall plate
screw (2)
Cable tie (1) not shown
–2–
Dome
Specifications/Features
• Designed for RV use
• Durable UV and weather resistant
• 360° Signal Reception
• High Definition VHF/UHF Digital
Signals
• ATSC 3.0 Ready
• Amplified
• State of the art pHEMT technology
with 4G LTE Filter
• Range – Up to 55 miles*
• Height – 8.05”
• Diameter of dome – 18.2”
• Frequency Range:
– VHF 54 to 216 MHz
– UHF 470 to 700 MHz
– FM 87.5-108 MHz
• Gain – 18 dB
• Noise – 1 dB
• Impedance – 75 ohms
• Power Supply – DC 12V
• (1) WiFi antenna**
• (2) LTE antennas**
** For use with the Winegard Gateway
Parts Included
Tools needed for installing (not included) – Butyl Tape, Pencil, Scissors,
Hole Saw, Drill, Phillips Screwdriver, Crimping Tool, 18AWG Power Wire
*Antenna mileage figures based on
average terrain. Actual receiving distance
will vary based on transmitting power,
transmitting antenna tower height,
global pattern of transmitter, height of
receiving antenna, weather conditions, &
terrain between receiving path including
trees, buildings, hills, mountains, etc.
WINEGARD COMPANY
Tolerances
unless noted:
18.20
8.05
AIR 360 PLUS DIMENSIONS
TRADE SECRET
The information and data contained herein is secret and shall not be disclosed,used or duplicated
for any purpose whatsoever without written permission of WINEGARD COMPANY, 3000 Kirkwood ST.,
Burlington, Iowa 52601. This legend shall be marked on any reproduction hereof in whole or in part.
Reciept of this document shall be deemed acceptance of the conditions specified herein.
.XX
.XXX
HOLE
ANGLE
ECN NO. DATE REV DESCRIPTION BY
P/N: CONNECT_2_PREWIRE_BASE_DOME_2 DRAWN BY: D. NEUWEG
SCALE: 0.200 DATE: Mar-28-19
SHEET 1of 1
DWG: AIR_360_PLUS_DIMENSIONS
8.05” Ht.
18.2” Dia.

7" MAX ROOF THICKNESS
OPTION 3 - GATEWAY ON CEILING
COMPATIBLE WITH ROOF RADIUS OF 230 INCHES TO FLAT
1" HOLE IN ROOF
OTA CABLE WIFI/4G CABLES
1" HOLE IN CEILING*
GATEWAY
ETHERNET CABLE (OPTIONAL)
PREWIRE HOLE COVER
*MUST BE BELOW OUTDOOR UNIT
RED WIRE - TO SWITCH
BLACK WIRE - TO GROUND
PARK CABLE IN
TV OUT 1
TV OUT 2
TO ANT IN
+12V DC
GROUND
+12V DC
3A FUSE RECOMMENDED
WIFI POWER CABLE
ANT IN *Must be below outdoor unit
Compatible with roof radius
of 230 inches to flat
Gateway
1"hole in roof
OTA cable
WiFi power cable
Red wire to switch
Black wire to ground
Ethernet cable (optional)
7"max roof thickness
To Ant in
3A fuse
recommended
+12V DC 1"hole in ceiling*
Prewire hole cover
+12V DC
TV out 2
TV out 1
Ant in
Ground
–3–
WiFi/4G cables
Park Cable in
Product Information
The Winegard®Air™360+system will bring in over-the-air local broadcast
television out of the box but has also been designed with the ability to work
with the Winegard Gateway as a WiFi and 4G LTE Extender. It is not intended
to work with any other router system.
The Air 360+is designed for RVs with a roof-radius of 230 inches to flat and
with a maximum 7 inch roof thickness.
The Air 360+allows the Winegard Gateway™to be installed in two locations;
inside the dome of the antenna or on the ceiling of the RV. For better
performance, it is recommended to install on the ceiling of the RV shown in
Option A below, however either option is acceptable.
The Air 360+can replace another TV antenna and can utilize the coax cable
that has already been installed. If doing this, you must ensure the coax
runs to the Winegard antenna wall plate/power supply and, if the Winegard
Gateway is to be installed, that the power cable is routed to the Gateway wall
plate/power supply.
It is recommended to install the Air 360+before attempting to install the
Gateway™system. Winegard recommends installing the Gateway directly
under the Air 360+. Once the Air 360+has been installed, there are two
requirements to finding a location on the RV ceiling for installation: +12VDC
must be present, and the three WiFi/4G antenna cables from the Air 360+
must be able to reach the connection points on the Gateway router.
A. Ceiling Mount Install (Recommended)

7" MAX ROOF THICKNESS
OPTION 4 - GATEWAY IN DOME
COMPATIBLE WITH ROOF RADIUS OF 230 INCHES TO FLAT
GATEWAY
1" HOLE IN ROOF
ETHERNET CABLE (OPTIONAL)
PARK CABLE IN
TV OUT 1
TV OUT 2
TO ANT IN
RED WIRE - TO SWITCH
BLACK WIRE - TO GROUND
+12V DC
GROUND
+12V DC
3A FUSE RECOMMENDED
OTA CABLE
WIFI POWER CABLE
ANT IN
–4–
Compatible with roof radius
of 230 inches to flat
Gateway
1"hole in roof
OTA cable
WiFi power cable
+12V DC Red wire to switch
Black wire to ground
Ethernet cable (optional)
TV out 2
TV out 1 +12V DC
Ant in
Ground
7"max roof thickness
To Ant in
3A fuse
recommended
Park Cable in
Installation Instructions
Safety Recommendations
Do not attempt to install this system in the rain or under any wet conditions.
Do not paint this antenna. Painting the antenna will void the warranty.
Before mounting the antenna, determine locations for both the TV antenna
wall plate/power supply and Gateway wall plate/power supply. Keep in mind
the following:
• Coaxial cables will have to run from the power supply to the antenna and
from the power supply to each television.
• If using the Air 360+to receive FM stations, an additional coax cable
(not provided) will have to run from the wall plate to the coax to audio cable
(provided) and into the radio.
• Coax cables will have to be routed through the roof directly under the
perimeter of the antenna. It will not seal correctly for the cables to exit under
the flange. Failure to install correctly could cause damage to the antenna and
possibly the RV.
• A 12 V connection must be made to the back of both power supplies.
B. Air 360+ In Dome Install
Product Information cont.

–5–
Installation Instructions cont.
• The Winegard®Gateway™can always be installed later, however it is
recommended to run the power cable to the intended mounting location of
the Gateway router.
Choose a location for the antenna that meets the following requirements:
• Offers enough support for a secure installation
• Maintains adequate clearance from the edge of the roof and any
obstructions:
– clearance distance of 24 inches needed from center of antenna to front of
the vehicle.
– clearance distance of 18 inches needed from center of antenna to nearest
obstruction and to the edge of the roof.
Step 1 – Remove the dome of the antenna by unscrewing the 4 Phillips screws
on the side of the dome. Carefully remove the dome and set it on its side as a
coax cable is connected to the antenna attached to the roof of the dome.
Step 2 – Place the base of the antenna in the location you intend to mount
with the flange indicating FRONT facing the front of the vehicle. Next, with a
pencil, trace around the base of the unit and the cable pass-thru hole that the
coax cable exits. Remove the base from this location.
> If installing the Winegard Gateway on the RV ceiling continue to Step 3.
> If installing the Winegard Gateway in the dome of the Air™360+continue
to Step 11.
24"18" Obstruction
Front of vehicle
18"
Top of antenna

Front of vehicle
Trace antenna base and
cable pass-thru hole
FRONT

–6–
L
N
M
Cable Feed-Thru
O
Figure 1
F
R
O
N
T
R
E
A
R
C
A
B
L
E
P
A
S
S
T
H
R
U
Gateway Ceiling Mount Installation (recommended)
Step 3 – Where the cable pass thru
hole was traced, drill, using a hole
saw, a 1"-1½" diameter hole through
the roof and ceiling of the vehicle.
Be careful not to damage any wiring
between the roof and ceiling.
Do not exceed 1½".
Step 4 – Replace the dome. Verify
the dome holes align with the base
holes. Ensure the dome and gasket
are completely tight and screw in the
four Phillips screws.
Step 5 – Connect the provided 20’ coax
cable to the coax cable that exits the base
of the Air 360+. If replacing an existing antenna, connect the coax cable that
is already ran to the coax cable that exits the base of the Air 360+.
Step 6 – Feed all 4 cables (Coax, Yellow, Green, and Red) into the roof of the RV.
Note: The coax cable will need routed wherever the antenna wall plate/power
supply is going to be installed.
Step 7 – It is recommended to use Butyl tape (not included) for extra
protection under the entire base flange before screwing to the roof. Reposition
the base of the antenna in the location you intend to mount with the flange
indicating FRONT facing the front of the vehicle. Screw in 6 mounting screws
into the 6 mounting holes around the flange of the base and into the roof.
Step 8 – Next, add approved sealant (check with RV Manufacturer) completely
around the flange base and over each screw.
WARNING: Ensure the gasket of the dome is complete sealed and that there
are NO gaps between the sealant and the base of the Air 360+. Failure to do
so could lead to water damage in the RV.
> If planning to install the Winegard Gateway now or at a later time:
Step 9 – Run the Gateway power cable from the hole where the three
antenna cables (Yellow, Green, and Red) enter the ceiling of the RV to the
predetermined location of the Gateway wall plate/power supply. The white
connector of this power cable should be at the same location as the Yellow,
Green, and Red connectors. The Winegard Gateway will use this power cable.
The bare wires of this power cable should be routed to where the On/Off
switch will be for the Winegard Gateway extender.

–7–
Figure 2
Gateway Ceiling Mount Installation (recommended) cont.
> If installing the Winegard®Gateway™now, please review the Winegard
Gateway installation manual followed by reviewing the Power Supply
Installation on page 8 of this manual.
> If installing the Gateway at a later time continue to
Step 10.
Step 10 – Zip tie (provided) the prewire power cable
along with the 4G LTE and WiFi cables (Yellow, Green,
and Red) to the notch on the backside of the white
prewire hole cover shown in figure 2. Make sure all
the cables are inside the ceiling and screw the white
prewire hole cover with 2 white screws (provided)
into the ceiling.
Continue to the Power Supply Installation section of this manual.
Gateway In Dome Mount Installation
Step 11– Using a hole saw, drill a 1"-
1½" diameter hole through the roof
of the vehicle. Do not drill into the
ceiling and be careful not to damage
any wiring between the roof and
ceiling. Do not exceed 1½".
Step 12– Pull the Yellow, Green, and
Red Cables into the dome from the
Cable Pass Thru hole. Secure the
Yellow cable into the A, B, C, and
D clips. Do the same for the Green
cable into the E, F, G, and H clips.
Continue clipping in the Red cable
into the I, J, and K clips. See figure 3.
Step 13 – Next, using the provided cable tie, zip tie the Gateway prewire
power cable, around 3 inches from the white connector, to tab O in figure 1
on page 6. With scissors, clip off the excess cable tie after the power cable is
secured. Route this cable into the hole drilled into the roof of the vehicle all
the way to the predetermined location of the Gateway wall plate/power supply.
The Winegard Gateway will use this power cable. The bare wires of this power
cable should be routed to where the On/Off switch will be for the Winegard
Gateway extender.
A
BC
D
E
F
G
H
IJ
K
1
2
3
Cable Feed-Thru
Figure 3
F
R
O
N
T
C
A
B
L
E
P
A
S
S
T
H
R
U
R
E
A
R

–8–
Gateway In Dome Mount Installation cont.
> If installing the Winegard Gateway now, please review the Winegard Gateway
installation manual followed by reviewing the Power Supply Installation on
page 9 of this manual.
> If installing the Gateway at a later time continue to Step 14.
Step 14 – Replace the dome. Verify the dome holes align with the base holes.
Ensure the dome and gasket are completely tight and screw in the four
Phillips screws.
Step 15 – Connect the provided 20' coax cable to the coax cable that exits the
base of the Air 360+. Feed this cable through the hole drilled in Step 11 and
route the cable to where the antenna wall plate/power supply will be located.
If replacing an existing antenna, connect the coax cable that is already ran to
the coax cable that exits the base of the Air 360+.
Step 16 – It is recommended to use Butyl tape (not included) for extra
protection under the entire base flange before screwing to the roof. Reposition
the base of the antenna in the location you intend to mount with the flange
indicating FRONT facing the front of the vehicle. Screw in 6 mounting screws
into the 6 mounting holes around the flange of the base and into the roof.
Step 17 – Next, add approved sealant (check with RV Manufacturer)
completely around the base and over each screw.
WARNING: Ensure the gasket of the dome is complete sealed and that there
are NO gaps between the sealant and the base of the Air 360+. Failure to do
so could lead to water damage in the RV.
Continue to the Power Supply Installation section of this manual.

–9–
Step 1 – The power supply may be flush mounted in most standard electrical
boxes. To flush mount, cut a hole in the wall to fit the box. Run two #12 wires
between the wall plate and +12 VDC source, and route downlead cable to this
location.
Step 2 – Make a 12 volt connection from the RV to the power supply. Install
the supplied terminals on wires from +12 VDC source, and crimp the
terminals with an appropriate crimping tool.
Step 3 – Push the wires onto tabs on the back of the power supply. (“PWR”
and “GND” are also noted on the underside of the power supply electronics
board).
Step 4 – Connect the coax cable from the antenna to the “ANTENNA” port on
the power supply, and tighten until fingertight. Then, tighten ¼ turn more.
Step 5 – If hooking up the antenna to two televisions, connect a coax cable
from the “SET 2” port to the “Antenna In” port on the second television.
If hooking up a cable input, connect the cable input to the “CABLE” port on
the power supply.
Step 6 – Mount the power supply in wall with the provided screws.
Step 7 – Connect a coax cable from the coax port on the front of the power
supply to the “Antenna In” coax port on the main TV.
Step 8 – Press the “ON” switch on the front of the power supply, and check
that the wall plate indicator light is on.
This unit is equipped with a polyswitch, which will shut down +12 VDC if
there is a direct short between the antenna and power supply. The indicator
light will not light. Once the short is eliminated, the device will reset itself.
Power Supply Installation – TV Antenna
WARNING: The power supply should be turned off when connecting cables.
Coaxial
port for
main TV
On/Off
button Antenna
port
Power &
Ground
tabs
Cable
port
Set 2
port
Indicator
light