Winegard Movin' View MV-0500 User manual

1
Movin’ViewTM
Automatic Digital Satellite Mobile Antenna
ModelMV-0500
Made in the U.S.A.
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
319/754-0600 • FAX [phone] • www.winegard.com
Printed in U.S.A. © Winegard Company 2002 2451018
WINEGARD®

2
DIRECTV®is an official trademark of DIRECTV, a unit of GM Hughes Electronics Corporation.
DISH NetworkTM is an official trademark of EchoStar Communications Corporaton.
DIGITAL BROADCAST SYSTEM
SATELLITE(S)
Introduction
Congratulations! You have purchased one of
Winegard’s latest developments in the mobile satel-
lite reception product line —the Movin’ViewTM.
This system, used with your digital satellite receiver,
will deliver the best reception possible using GPS
(Global Positioning System) and precision gyro-
scopes.
How Does Digital Satellite
TVWork?
Satellite programming originates from an “uplink”
facility on Earth — the facility receives many signals
from different sources, combines the signals digitally
and transmits to the satellites. The satellites (22,300
miles above Earth) receive the uplink signal, amplify
it and then transmit it back to earth in the
Ku frequency band. This signal
is concentrated and reflected to
the LNBF* located at the “focal
point” of the dish. The LNBF
amplifies and converts the signal to
the 950 to 2050 MHz range. The signal
is then passed through a coaxial cable
to the receiver where individual chan-
nel selection and processing take
place.
For Programming information call:
DISH NETWORKTM - 1-800-333-DISH (1-800-333-3474)
DIRECTV®- 1-800-DIRECTV (1-800-347-3288)
ExpressVu TM 1-888-SKY-DISH (1-888-759-3474)
Your new Winegard RV Digital Satellite System is an easy-
Introduction/How Does Digital Satellite TV Work?
PROGRAMMING UPLINK
CONTROL CENTERS
HIGH POWER KU-BAND
DOWNLINK SIGNAL
WINEGARD DIGITAL SATELLITE
SYSTEM ANTENNA
RECEIVER
UPLINK SIGNAL TELEVISION
SET
to-use satellite TV reception system. Because it mounts
on the top of your recreational vehicle, it goes where you
go and provides quality reception of digital satellite sig-
nal in the continental United States only.
* Low Noise Block Converter Feed

3
1 Cable entry plate
1 large yellow spade connector
2 small red spade connectors
All required screws and washers
1 base with electronics, dish, dual LNBF
1 tube silicone
1. Open box and remove packing material.
2. Lift unit out of box vertically. Do not turn box and
“roll” out, or turn upside down to remove.
!
USE 2 PEOPLE
when removing the unit
from the carton.
Parts Included • Tools Needed • How to Unpack
If using knife to open
carton, BE CAREFUL.
Do not cut the dome on
the unit.
About this manual —
We hope this manual will provide clear instructions to install and operate the MV-0500.
Two symbols have been used —
!Indicates caution should be taken! Indicates suggestions to make
processes easier for you.
PARTSINCLUDED:
1 Radome
3 base mounting feet
1 Power switch
2 Wall plates (white & brown)
1 Surface mount bracket
2 Cable clamps
LIFT UNIT STRAIGHT UP
TOOLSNEEDEDFOR UNPACKING & INSTALLATION:
UNPACKINGTHEUNIT
7/16” open end wrench
Level
Drill w/3/4” bit
1-1/4” hole saw (if mounting switch in wall)
5/16” Socket for roof screws
1/8” Allen wrench
1/2” Open end wrench
Crimping tool for coax connections
Crimping tool for electrical connections
Small blade screw driver
Pliers
Sealant (consult RV manufacturer for proper type for
your roof material)

4
Installation Diagram
BACK OF
VEHICLE
FRONT OF VEHICLE
GPS ANTENNA
ADJUSTABLE
BASE FOOT
ADJUSTABLE
BASE FOOT
REAR BASEFOOT
MUST DIRECTLY
FACE REAR OF
VEHICLE
LEVELING
SCREW
LEVELING
SCREW
LEVELING
SCREW
CONTROL
UNIT
POWER
SUPPLY
REFLECTOR
HEYCO®
CONNECTORS
FIGURE 1

5
6. On each foot, screw the flange nut to the base of
the leveling screw on the mounting foot, flange up.
Place rubber washer, with the rubber side up, on
the nut, Figure 2. Push mounting foot under base.
Push foot screw through the base and tighten lock
nut to secure foot to base. Be sure the base feet are
pointing away from the base. Base feet will be re-
moved later during install.
!
Installation
Install in DRY conditions only!
If you have trouble seeing the numbers,
try using a magnifying glass!
FIGURE 2
FIGURE 3
OBSTRUCTION
UNIT BASE
Installing unit on roof of vehicle —
5. Determine which programming you will be using.
This will determine how you set your switches.
For DISH NetworkTM set
switches to 119°.
For DIRECTV®set switches to 101°.
For ExpressVuTM set switches 092°.
LEVELING SCREW
RUBBER WASHER
FLANGE NUT
(FLANGE UP)
Obstruction Ht. Unit Clearance
8” ..........................................4”
10” ................................... 11.5”
12” ...................................... 19”
15” ...................................... 32”
IMPORTANT! Do not install this system
in the rain, or under any wet conditions. Moisture
may affect electronics and void your warranty!
1. For best performance and to reduce signal acquisi-
tion time, park vehicle on a level surface.
2. Select a level spot on your roof for installation.
• The unit should be no more than +/-1° off level.
• Be sure no roof-mounted equipment is
blocking the satellite “line of sight.”
• You will need to decide where the wires will enter
the vehicle. A coax and an 18 gauge power wire
will need to be placed in the vehicle. The power
wire will go to the nearest +12 VDC power source;
the coax will be routed through the demulitplexer to
your satellite receiver. These wires should be hidden.
3. Remove screws holding dome to base and remove
dome. Place dome in safe spot to avoid damage. Place
base on vehicle roof in the location selected.
4. Remove wire ties used for shipping. There are
three; one on each side of the reflector and one at the
the rear of the reflector holding down the counter-
weight. See Figure 1, page 4.
MOUNTING
FOOT
7. After selecting location for unit (see step 2),
put the unit on the centerline of the coach.
REAR MOUNTING FOOT MUST FACE
DIRECTLY OFF REAR OF VEHICLE,
Figure 1. There is a 30 foot power cord and 30
foot coax cable going through the Heyco®con-
nectors on the base.
Placing the rear base bracket on the centerline,
facing the rear of the vehicle, will center the unit.
8. Using the chart,
determine the
minimum distances to
other equipment.
Measure these
distances as
demonstrated in Figure 3.

6
123456789012345678901234567890121
1
2345678901234567890123456789012
1
1
2345678901234567890123456789012
1
1
2345678901234567890123456789012
1
1
2345678901234567890123456789012
1
123456789012345678901234567890121
10. Clean roof area where the base feet will be
attached to the roof. Do not erase your marks!
11. Put approved sealant in the area under the base
feet. Place base foot on top of the sealant and
screw down using (2) #10 screws (provided) for
each base foot.
12. Unscrew the locknuts in the base and remove
the base from feet. Put the other (4) #10 screws
into the roof through the remaining holes in the
base feet.
Installation
ROOF INSTALLATION, continued
9. Place the unit on the roof in its permanent location
and mark around the base bracket, Figure 4. (Make
sure the rear adjustable base foot is directly facing
the back of the coach.)
FIGURE 4
FIGURE 5
The GPS antenna is pre-wired and has a 3 foot cable
running through one of the Heyco®connectors.
When deciding where to place GPS antenna, DO
NOT SECURE! After wiring the receiver and initializ-
ing your system, you will need to test the system
(“Initializing and replacing dome” on page 8).
Determine location for GPS antenna. It is recom-
mended you place the GPS antenna between unit base
and side edge of vehicle, 90° from rear mounting
bracket, Figure 6.
The recommended location for the GPS antenna is
based on having a level location and a clear view of
the sky. If another location, further from the base, is
desired, loosen the Heyco connector and pull out addi-
tional wire in the base. You must re-wrap and re-tie
the GPS cable inside the dome to prevent interfer-
ence with the LNBF. Failure to do so will result in
malfunction! Tighten Heyco connectors when done.
IMPORTANT! The GPS must be located away from
obstructions on roof of vehicle and other obstructions
such as trees, tall buildings, etc. You must have a
clear view of the sky for proper operation.
GPS installation —
FIGURE 6
13. After all base brackets are secured to roof, put
sealant on top of foot and screws. Place base on level-
ing screws located on base feet and install nut and
rubber washer on leveling screw.
14. Leveling the base is done by tightening or loosen-
ing the flange nut under the base, Figure 5.
Use an electronic level to adjust base so there is no
more than +/- 1° off level in all directions. Place
level on base of unit if possible. (If your level will not
fit inside the base plate, place on outside edge.) Level
front to back and side to side. Raise and lower by ad-
justing flange nut under base. After leveling base,
secure inside base with rubber washer, rubber side
down toward base, and lock nut.
BASE EXTERIOR
FOOT
LEVELING
SCREW/FLANGE
GPS
ANTENNA
HEYCO®
CONNECTORS
REAR BASE FOOT
MUST DIRECTLY FACE
REAR OF VEHICLE
FRONT OF VEHICLE

7
CABLE-
ENTRY
PLATE
CABLE CLAMP -
EVERY12”-16”
1. Decide the best location for the cables to enter the
vehicle, and the location of the switch and receiver
(see “Installing the switch and receiver” below.) Drill
a 1/2” hole in the roof, push wires inside. Make
proper connections (remember you must have fil-
tered +12 VDC power source).
2. Place cable-entry plate over hole and cables. Screw
in place. Seal plate and screw holes with approved
sealant (not included).
FIGURE 7
Cable entry installation —
3. Depending on the length of the cable on the roof,
you may need to use cable clamps or wire ties (not
provided) between the unit and your cable-entry plate.
Clamping the cable every 12”-16” should eliminate
any unnecessary cable movement, Figure 7.
Installation • Wiring
INSTALLATION
1. Decide the location of the power on/off switch.
Be sure the switch is turned off before you begin!
See diagram below.
Wall or panel mount: Drill 1-1/4” hole, pull wires
through wall or panel.
Surface mount: Determine location and direction of
box. Mount box feed wire into one of the box open
ings.
Select plate cover (brown or white provided) and snap
the rocker switch into the switch plate. Be sure switch is
off!
2. Connect +12 VDC power from vehicle, using red
spade connector, to isolated spade on switch.
3. Connect red power wire from MV-0500 using red
spade connector to center spade on switch.
4. Connect vehicle ground and black ground wire,
using yellow spade connector, to silver spade on
switch.
FILTERED
+12 VDC
FROM
VEHICLE
INSTALLINGTHEPOWERSWITCHDIAGRAM
STEP 4
STEP 3 STEP 2
TWO BLACK GROUND WIRES
1 FROM VEHICLE
1 FROM MV-0500
ON/OFF ROCKER
WITH LIGHT
(SHOWN IN OFF
POSITION.)
MV-0500
RED POWER
WIRE
FIGURE 8

8
Initializing & replacing the dome after
connecting the receiver(s) —
1. Be sure vehicle is in a location free of all obstruc-
tions and with a clear view of the satellite.
2. DO NOT MOVE VEHICLE during the first initial-
ization. Power up unit, turn on receiver. FOR THE
FIRST TIME ONLY, the unit may take up to 10 min-
utes to initially find the satellite signal. The GPS is
also initializing at this time. After the GPS initializes,
the unit will begin searching for the correct satellite.
3. If the GPS does not initialize at this time, turn off
the unit. You may need to move the GPS antenna to a
different location on your roof. After you move the
GPS, DO NOT SECURE TO ROOF.
4. TEST YOUR SYSTEM BEFORE SECURING
THE GPS ANTENNA. Make sure the TV/receiver
have the correct satellite.
5. After the correct satellite has been found, secure
GPS antenna by removing adhesive backing and se-
curing to roof.
6. Install dome. NOTE: After Heyco conmectors are
tightened, apply bead of silicone around the connec-
tor where the exterior hex nut touches the base and
around the cables where they enter the Heyco on the
exterior of the unit. See drawing below. If second
receiver is not used, apply silicone to seal center hole
of third Heyco. See drawing below.
8. Before inserting screws on sides of dome, apply
silicone to ENTIRE oval slot in gasket AND to screw
threads, then insert screws and tighten. See drawing.
Connecting two receivers
1. Connect the coax cable coming from the MV-0500
to the “ SATELLITE IN” input on the primary re-
ceiver. The primary receiver is the reciever used most
often.
2. Run a second cable through the empty Heyco open-
ing and connect to the ground block-type feed through
and connect the other end of this cable to “Satellite
IN” input on the second receiver.
Installation • Wiring
Connecting one receiver
1. Connect the coax cable from the MV-0500 to the
“SATELLITE IN” on the receiver.
Connecting the receiver —
SAT RECEIVER
WIRING ONE RECEIVER
SATELLITE IN
PRIMARY
RECEIVER
USED ONLY WITH
2 RECEIVERS
GROUND BLOCK
CUSTOMER/INSTALLER
PROVIDES COAX
SAT RECEIVER
WIRING TWO RECEIVERS
SATELLITE IN
SATELLITE IN
SAT RECEIVER
FILL OVAL
WITH SILICONE FILL SCREW THREADS
WITH SILICONE
BEFORE INSERTING
HEYCO CONNECTOR
APPLY SILICONE BEAD IN
HOLE WHERE COAX ENTERS
APPLY SILICONE BEAD
AT BASE OF HEYCO
CONNECTOR
UNIT BASE

9
Operation
Yournew MV-0500 features:
• GPS technology
• Fast signal acquisition times
• Easy “one-button” operation
• Ability to toggle between satellites using
remote control, if subscribing to multi-
satellite programming
Vehicle must be parked.
1. Turn on receiver and television set. This unit
will not operate unless receiver is on. Be sure
your TV is turned to channel 3 or 4.
2. Turn your +12VDC power switch to ON posi-
tion.
3. Allow up to 3 minutes for signal location. Sat-
ellite signal acquisition will occur with normal
operating conditions.
NOTE: Acquisition time will be longer if the ve-
hicle has traveled more than 600 miles without the
unit in use. If you have traveled this distance
without using the unit, signal acquisition may
take up to five minutes.
4. If you do not have a signal after three minutes, be
sure there are no obstacles preventing signal acquisition.
(Trees, hill, buildings or other structures can block the
signal.) Move to an open area so your system can “see”
the satellite signal.
• Low maintenance
• Compatible with continental U.S. digital satel
lite receivers
• Winegard warranty
To operate your system —
To toggle between satellites when subscribing to multi-satellite programming—
The MV-0500 will toggle between two different
satellites. Both DIRECTV and DISH Network
have programming on more than one satellite.
When a channel is selected on the remote control
and it is not located on the satellite the unit is
currently on, the system on the vehicle will auto-
matically move to the new satellite.
DIRECTV programming
1. There is NO SETUP required for DIRECTV.
When you request a channel located on a differ-
ent satellite, the unit will automatically move to
that satellite.
DISH Network programming
NOTE: This must be a DISH 500 system. These steps
must be done each time the receiver loses 110 VAC
power.
1. Let unit acquire the satellite signal on satellite 119.
2. After signal has been acquired, press the MENU key on
the remote control or receiver.
3. Go into the SYSTEM SETUP menu.
4. Go into the INSTALLATION menu.
5. Go into the MULTI-DISH installation.
6. Scroll down to the CHECK SWITCH button and select.
7. The receiver will verify that you want to perform a
“Check switch.” Select CHECK.
8. The receiver will begin checking your switch by tog-
gling between transponders. When this is completed, a
message stating “satellite reception is verified” will show.
When it does, select OKAY. If this message does not ap-
pear, repeat steps 1 - 7.
9. Your system is now set up to toggle between satellites.
It will automatically move to correct satellite when chan-
nel is selected.

10
Signal strength screen meter shows some
signal strength, but constantly moves up and
down, and is never locked on satellite.
Unit continues to move, but never finds any signal.
The unit continues to move and the signal strength
screen shows that it is finding the satellites, but will
never lock onto any satellite. Continues to search.
The unit moves around in circles, then points off
the front of the coach.
the next steps. Voltage must be +12 VDC, except at the
LNBF, see Figure 9, page 11.
6. To check voltage at connections, see Figure 9 on
page 11. FOLLOW THE NUMERICAL SEQUENCE
ON THE DRAWING AND CHECK VOLTAGE AT:
#1. Power Supply.
#2. LNBF voltage. Disconnect the coax cable from
the LNBF. Check voltage from the middle wire to
the shield. There should be +12 to +19 VDC. If no
voltage is present, make sure receiver is on and
check for +12 to +19 VDC at ends of gray coax
cable (remove at box junction).
#3. ‘Mini-cable’ connection voltage at Control Box.
#4. Coax cable at Control Box going to
Heyco connector.
7. Are the rotary dip switches in the correct position (101
or 119 or 092)?
8. If the unit still does not have a signal, power off and
power back on.
IF YOU DO NOT HAVE A SIGNAL:
1. The signal may be blocked by trees, hills or
structures. Pull into an area where no trees or
buildings are in the line of sight from unit to the
satellites.
2. Check your +12 VDC power switch. Make
sure it is in the ON position.
3. Check your connections. The receiver must
be connected to the power and coax connected
from receiver to the satellite dish.
4. Check your power supply. The +12 VDC
power supply must be hooked up. Check for +12
VDC on the roof at the connector.
5. Is the rear adjustable base bracket facing the
rear of the vehicle? See Figure 1, page 4.
6. Loss of signal may also be caused by snow on
roof of vehicle.
NOTE: The power rocker switch must be ON for
Check your power voltage. You may have dirty
power. You must have a minimum of +12 VDC.
Make sure receiver is on and connected properly.
Check rotary dip switches for correct setting. (i.e.
DISH network 119°, DIRECTV 101°, etc.).
PROBLEM SOLUTION
Be sure the switches are set on the correct numbers —
see page 5, step 5.
The GPS is not acquiring a signal.
Troubleshooting