Winegard Sensar HV CC-25HV User manual

Model CC-25HV
Antenna Retrofit Kit
Coast to Coast RV Services
20 George Young Street, Auburn NSW 2144
Postal Address: PO Box 415, Regents Park NSW 2143
Phone: [phone]
Fax: [phone]
Email Technical: [e-mail]
Email Warranty: [e-mail]
2452255

Pull the e-clip off of the pin, and
remove the pin from the leveling
bracket.
2
Existing
Antenna
Assembly
Retrofit
Antenna
Assembly
Leveling
bracket
Pin
Remove the cap from the coax
connection port.
Thread the 140 cm coax between
the boom and the center of the
lower element housing. Continue
to thread the coax in an S-curve
between the boom and the center
of the lower element housing.
NOTE
Make sure that the other end of the 140 cm coax leads to the wall
plate/power supply.
Replacing a Winegard Sensar HV Antenna
with the Sensar HV Retrofit Kit
1
Mounting
bracket
140 cm coax
Insert the pin through the leveling
bracket and the elevating gear. Push
the e-clip over the end of the pin.
Using a wrench, loosen and remove
the 140 cm coax from the coax
connection port shown here.
Boom
3
Mounting bracket
Remove the existing antenna assembly from the mounting bracket.
Lower element housing
4
Elevating gear
Connect the coax to the coax
connection port, and tighten until
fingertight. Then, tighten ¼ turn
more.
Using the retrofit antenna assembly, insert the elevating gear in-between the
sides of the leveling bracket. The elements should be on top of the boom. The
holes in the sides of the leveling bracket and in the elevating gear should align.
Cap
5
6
7
8

Pull the e-clips off of the pins, and
remove the two pins from the
leveling bracket.
Mounting
bracket
2
1
Existing Antenna Assembly
Retrofit
Antenna
Assembly
Leveling
bracket
E-clip
Remove the cap from the coax
connection port. Now, install a
connector on the end of the coax
cable. Refer to the next page for help.
Thread the existing coax cable
between the boom and the center
of the lower element housing.
Continue to thread the coax in an
S-curve. Thread the coax over and
then under the boom.
Replacing a Winegard Sensar Antenna
with the Sensar HV Retrofit Kit
Mounting
bracket
Pin
Coax
Connection
Port
Insert the pin through the leveling
bracket and the elevating gear. Push
the e-clip over the end of the pin.
Using a wrench, loosen and
remove the coax cable from the
coax connection port shown here.
Cut the connector off the end of the
cable, and pull the cable out of the
Sensar antenna. Due to variations
in connector types and cable sizes,
a coax connector is not included.
3
Remove the existing Sensar antenna assembly from the mounting bracket.
4
Elevating gear
Boom
Using the retrofit antenna assembly, insert the elevating gear in-between the
sides of the leveling bracket. The elements should be on top of the boom. The
holes in the sides of the leveling bracket and in the elevating gear should align.
Cap
5
6
7
8
Lower
elemen
t
housing

If installing in
hot weather,
increasethese
dimensions 3 mm.
Fray braid back as far
as outer cover will
allow.
Trim braid close to
outer cover, and
remove 6 mm of inner
insulation, being careful
not to nick the center
conductor. Make sure
no foil or braid can
touch center conductor.
Slide connector tip
between braid and
inner insulation (braid
and foil, on foil shield
cable). Push connector
on cable as far as it
will go. Attach cable
with proper crimping or
compression tool. Do
not crush cable out-ofn
round.
Connect the coax to the coax
connection port, and tighten until
fingertight. Then, tighten ¼ turn
more.
Make sure that the other end of the coax cable leads to the wall plate/
power supply.
10
Turning on Power Supply
Operation
Raising Antenna
Turn the elevating crank clockwise in “UP”
direction about 13 turns or until some
resistance to turning is noted.
Turn power supply on to use either front or
rear output of the TV outlet. Neither outlet will
work unless the power supply switch is on.
NOTE
1
2
Rotating Antenna for Best Picture
Lowering Antenna to Travel Position
Make sure the antenna is in the “UP”/
deployed position. Pull down with both hands
to disengage ceiling plate. For analog signals,
rotate for best picture. For digital signals,
run a channel scan to find the best signal.
Rotate the antenna until the pointer on the directional handle aligns with
the pointer on the ceiling plate. Turn elevating crank counterclockwise in
the “DOWN” direction about 13 turns or until some resistance is noted. The
antenna is now in the travel position.
3
4
Antenna reception may vary based on transmitting antenna tower height, lobe pattern of the
NOTE
transmitter, height of the receiving antenna, weather conditions and terrain on receiving path
including trees, buildings and hills.
OFF
On/Off Button
Ceiling
Plate
9
Upper
element
housing
Boom
Coax
connection
port
ON
This unit is equipped with a
polyswitch, a current limiting
device, which will shut down +12 VDC if
there is a direct short between the antenna
and power supply. The green indicator light
will not light. Once short is eliminated, the
device will reset itself.
Thread the existing coax cable
between the boom and the center
of the upper element housing.
NOTE
Installing Connector on Coax Cable
Strip outer cover back
12 mm from end of
cable.
TIP
Lower the antenna to the travel position before traveling!

1
2
3
4
Do
Check parking location for obstructions before raising the antenna.
Carefully raise, lower, and rotate the antenna. If having trouble, check for
obstructions.
Rotate slowly when selecting a station, and check the fine-tuning on the TV.
Lower the antenna to the travel position before moving the vehicle.
Don ’t
Don’t force the elevating crank up or down or rotate the directional handle
hard against stops.
Don’t travel with the antenna in the up/deployed position. Stow the
antenna before traveling or when wind speeds reach +113 km/h.
Don’t leave the antenna partially deployed.
Don’t apply sealant over the top of the base plate.
www.winegard.com
©2012 Winegard Company Rev2 2/12 2452255
Winegard is a registered trademark of Winegard Company.
All trademarks are property of their respective owners.
2452255
1
2
3
4