WINGBO WBCF-BS13-BS15 Series User manual

PLEASE READ AND SAVE THESE INSTRUCTIONS
Fan wobble 3. Check whether the screw of the blade retracted to the motor is locked
WBCF-BS13-BS15 Series
WBCF-BS22-BS24 Series

Thanks for your purchase!
Should you have any questions or concerns, please do not hesitate to contact
us by mail address
Before using this ceiling fan with light, please read this manual carefully and
operate strictly in accordance with the procedures.
1 The input voltage of this product: 120V/60Hz
2 If you have insufficient knowledge of electrical appliances, be sure to hire an
experienced expert to install them.
3 Before installing and disassembling the ceiling fan light, please turn off the
power first. The installation must be installed in the order of ground wire, live
wire, and neutral wire. Before disassembly, it must be disassembled in the order
of neutral wire, live wire and ground wire to avoid electric shock.
4 The ceiling fan must be installed on a solid ceiling, and the location of the ceiling
fan must be able to withstand a gravity greater than 60 KG.
5 When installing the ceiling fan, all screws must be securely locked.
6 When the ceiling fan is rotating, no objects should touch the blades to avoid
danger.
7 The angle and elevation of the leaf frame are determined after many repeated
measurements, so it cannot be changed at will. When installing the leaf frame
and blades, special care should be taken not to force collisions. If the angle and
elevation angle of the leaf frame are deformed that will cause the ceiling fan to
shake.
1 Voltage: 120V/60Hz
2 Power: Motor power: 52inch-35W/64inch-40W LED power: 24W
3 Speed + Color change: 6speed+3 color temperatures(Cool white light 6500K+
warm light 3000K+ neutral light 4500K)
4 Number of rotating leaves: 3 blades
5 Fan blade material: Solid Wood
6 Motor material: Pure copper wire winding and high-quality silicon steel stator,
high efficiency, super quiet, energy saving.
7 Control method: Remote control
8 Diameter: 52inch / 64inch
9 Reversible：YES
3
Ⅲ、Basic parameters
Ⅰ、Precautions
1*Decorative cover
1*Instruction
1*Lamp Plate+LED
Ⅱ、Prepare tools before installation:
[e-mail]

R Clip pin
Set Screw
8
7
4.5"
4.5"
4.5"
4.5" 12"
1. Select the downrod
①. There are two downrods of 4.5inch and 12inch in the package, customers can
choose according to the height of the house.
②. The normal default is to install on the 4.5inch downrod.
③. How to replace the 12 inch Downrod:
A. Loosen the two fixing screws (as shown in Figure 2).
B. Push the downrod upwards (as shown in Figure 3) out of the horizontal tip (as
shown in Figure 4).
C. Then pull out the 4.5 inch downrod to replace another 12 inch downrod
(as shown in Figure 5).
D. After replacement, follow the above installation steps 4-3-2 to install until it is
restored to the state shown in Figure 1.
E. Finally, you must pay attention that the two fixing screws must be firmly locked.
Note:
a. According to the ceiling of different materials, use different screws to fix the
mounting bracket (as shown above).
b. After the bracket is fixed, it must be determined to be able to bear the weight
of more than 60 kg(test pull by hand) for safety.
c. Ceiling fans cannot be installed on gypsum ceilings.
d. To reduce the risk of fire, electric shock, or personal injury mount to an outlet
box marked"Acceptable for Fan Support".Use the mounting screws provided
with the outlet box. Most outlet boxes commonly used for supporting lighting
fixtures are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
2. How to install Suspension Installation
①.Remove the positioning screws from the fan body as follows and place them
side by side to proceed to the next step (Fig 6)
②.Get off the pin off the downrod by remove the R clip, and get the lead wire
through the downrod and canopy, then seat the downrod into the fan body &
rotate the downrod until the holes on the downrod will match with the holes
on the fan body, finally, you should get the pin through the holes and fix the
pin by the R clip in another side (Fig 7)
③.Tighten the two set screws removed previously.
Please use 8mm drill hole before installing with M6 expension screws
Notice: Make sure the fan blades at least 7 feet above the floor
12 3 4 5
6
3. Install the hanger bracket to the outlet box
a. Take off the screws on the outlet box.
b. Install the hanger bracket to the outlet box by screws
Decorative
cover
Coupling
cover
Coupling
cover
2. Concrete ceiling: First use an ∅8mm hammer drill bit to drill the hole according to the
length of the expansion screw, then use the equipped expansion screws (2 Pieces) to
fix the bracket on the ceiling, and then tighten the nut of the expansion screw.

9
1. Take out the blade screws and washers in the hardware bag (as shown in Figure 10 )
2. Align the blade screw hole with the motor blade plate hole, and tighten the screws
in turn (Figure 11)
VIII. Install lamp
1. Remove the three fixing screws from the lamp holder, and lock the lamp plate
to the lamp holder with screws.(Figure 12 )
2. Please check whether the driver output line and the LED source board are
tightly inserted, and plug the 2 light wires to the LED board properly.(Figure 13)
3. Install the lamp shade in place and rotate the lamp shade clockwise.(Figure 14)
9
11
12 13
Note: The solid wood fan blades have a certain squeezing space. The blades
must be installed with washers, and pay attention to locking with conventional
force. Do not continue to apply force after the blades are locked to continue
screwing in the screws, otherwise It will cause irreversible failures to the motor
coil!
14
10
screws and washers
to fix the blade
1. Connect the live wire from ceiling to receiver black wire(AC IN L).
2. Connect the neutral wire from ceiling to receiver white wire(AC IN N)
3. Connect the Grey wire(Motor U) from motor to Grey wire(Motor U) from
receiver.

Balance piece
2. Adjust with balance kit.
A. Take out the balance bag from the package box, use a balance clamp to select
one of the fan blades and clamp the balance clamp on the edge of the tail end
of the fan blade (Figure 17)
B. Turn on the fan switch to see whether the wobble of the ceiling fan has been
reduced. If it does not improve, try another fan blade. Experiment with all the
fan blades in turn to find the blade with the weakest clamping balance.
C. Clamp the balance clamp on the fan blade with the weakest wobble, move it
in or out on the edge of the fan blade, turn on the ceiling fan to find the best
position of the balance clamp to control the wobble balance (Figure 17)
D. Take the balance sticker, tear off the double-sided tape of the balance sticker,
and stick the balance sticker on the center of the blade at the position of the
balance clip (Figure 17)
16
(Figure 15)
17
1. Change the position of the fan blades:
a. There is no improvement after the swap blades position. Please remove
the fan blades 2 and 3 and re-lock each other to obser ve the effect.
XII.Balance adjustment method of ceiling fan.
If there is any wobble after ceiling fan installation, please confirm whether
the screws that fix the hanger ball, mounting bracket, hanger, blade holder,
and blade are locked. If one of the above parts is not locked, please re-lock it.
If it is locked, please adjust it as follows.
15
4. Connect the red wire(Motor V) from motor to red wire(Motor V) from receiver.
5. Connect the yellow (Motor W) from motor to yellow wire (Motor W) from
receiver.
6. Connect the blue wire(FOR LIGHT) from motor to blue wire (FOR LIGHT) from
receiver.
7. Connect the white wire(FOR LIGHT) from motor to white wire(FOR LIGHT)
from receiver.