WINGBO WBCF-BS88 Series User manual

WBCF-BS88~BS95
PLEASE READ AND SAVE THESE INSTRUCTIONS
Fan wobble 3. Check whether the screw of the blade retracted to the motor is locked
WITHOUTLIGHTKIT WITHLIGHTKIT

Before using this ceiling fan with light, please read this manual carefully and
operate strictly in accordance with the procedures.
1 The input voltage of this product: 120V/60Hz
2 If you have insufficient knowledge of electrical appliances, be sure to hire an
experienced expert to install them.
3 Before installing and disassembling the ceiling fan light, please turn off the
power first. The installation must be installed in the order of ground wire, live
wire, and neutral wire. Before disassembly, it must be disassembled in the order
of neutral wire, live wire and ground wire to avoid electric shock.
4 The ceiling fan must be installed on a solid ceiling, and the location of the ceiling
fan must be able to withstand a gravity greater than 60 KG.
5 When installing the ceiling fan, all screws must be securely locked.
6 When the ceiling fan is rotating, no objects should touch the blades to avoid
danger.
7 The angle and elevation of the leaf frame are determined after many repeated
measurements, so it cannot be changed at will. When installing the leaf frame
and blades, special care should be taken not to force collisions. If the angle and
elevation angle of the leaf frame are deformed that will cause the ceiling fan to
shake.
1 Voltage: 120V/60Hz
2 Power: Motor power: 30W LED power: 24W
3 Speed + Color change: 6 speed+3 color temperatures(Cool white light 6500K+
warm light 3000K+ neutral light 4500K)
4 Number of rotating leaves: 5 blades
5 Fan blade material: Solid Wood
6 Motor material: Pure copper wire winding and high-quality silicon steel stator,
high efficiency, super quiet, energy saving.
7 Control method: Remote control
8 Diameter: 60 inch
9 Reversible：YES
Ⅲ、Basic parameters
Ⅰ、Precautions
1*Decorative
cover
1*Instruction
Ⅱ、Prepare tools before installation: 5*Blades
Thanks for your purchase!
Should you have any questions or concerns, please do not hesitate to
contact us by mail address
[e-mail]
1*Lamp Plate+LED
5*Blades 1*Decorative ring
Gerneral
With
light kit
Without
light kit
Allen key

1. Select the downrod
a. There are two downrods of 4.5inch and 12inch in the package, customers can
choose according to the height of the house.
b. The normal default is to install on the 4.5inch downrod.
c. How to replace the 12 inch Downrod:
Notice: Make sure the fan blades at least 7 feet above the floor
4.5"
4.5"
4.5"
4.5" 12"
1). Loosen the two fixing screws (as shown in Figure 2).
2). Push the downrod upwards (as shown in Figure 3) out of the horizontal
tip (as shown in Figure 4).
3). Then pull out the 4.5 inch downrod to replace another 12 inch downrod
(as shown in Figure 5).
4). After replacement, follow the above installation steps 4-3-2 to install
until it is restored to the state shown in Figure 1.
5). Finally, you must pay attention that the two fixing screws must be firmly
locked.
2. How to install Suspension Installation
a. Remove the positioning screws from the fan body as follows and place
them side by side to proceed to the next step (Fig 6)
b. Get off the pin off the downrod by remove the R clip, and get the lead
wire through the downrod and canopy, then seat the downrod into the
fan body & rotate the downrod until the holes on the downrod will match
with the holes on the fan body, finally, you should get the pin through
the holes and fix the pin by the R clip in another side (Fig 7)
c. Tighten the two set screws removed previously.
12 3 4 5
Note:
1). According to the ceiling of different materials, use different screws to fix
the mounting bracket (as shown above).
2). After the bracket is fixed, it must be determined to be able to bear the
weight of more than 60 kg(test pull by hand) for safety.
3). Ceiling fans cannot be installed on gypsum ceilings.
4). To reduce the risk of fire, electric shock, or personal injury mount to an
outlet box marked"Acceptable for Fan Support".Use the mounting screws
provided with the outlet box. Most outlet boxes commonly used for
supporting lighting fixtures are not acceptable for fan support and may
need to be replaced.
Consult a qualified electrician if in doubt.
Please use 8mm drill hole before installing with M6 expension screws
3. Install the hanger bracket to the outlet box
a. Take off the screws on the outlet box.
b. Install the hanger bracket to the outlet box by screws
2. Concrete ceiling: First use an φ8mm hammer drill bit to drill the hole
according to the length of the expansion screw, then use the equipped
expansion screws(2 Pieces) to fix the bracket on the ceiling, and then
tighten the nut of the expansion screw.

VIII.Install the lamp.
1. As shown in Figure 12 below, remove the three fixing screws from the lamp
plate holder base and lock the lamp plate hole corresponding to the holder
base hole with screws.
9
9
VII.Install the blades.
1. Take out the blade screws from screws package, Install the blade to the motor and
tighten the screws.(Figure.10)
2. Install the blade assembly to the motor in place, make sure all the screws are
tighten properly.(Figure.11)
8
7
6
R Clip
pin
Set Screw
Decorative
cover
Coupling
cover
Coupling
cover
2. Plug the 2 light kit wires into LED module power socket. (Figure 13)
3. Install the lamp shade to the lamp plate in place properly. Then turn it
clockwise, Make sure the lamp shade tightening.(Figure 14)
IX
4. If you fan without light kit, please install the decorative ring to the blade.
(Figure 15-16-17)
screws and washers
to fix the blade
10 11
15 16 17
13 14
12
Allen key

(Figure 18-19-20)
1. Change the position of the fan blades: (Fig 21)
a. There is no improvement after the swap blades position. Please remove
the fan blades 2 and 3 and re-lock each other to obser ve the effect.
XI. Balance adjustment method of ceiling fan.
If there is any wobble after ceiling fan installation, please confirm whether
the screws that fix the hanger ball, mounting bracket, hanger, blade holder,
and blade are locked. If one of the above parts is not locked, please re-lock
it. If it is locked, please adjust it as follows.
2. Adjust with balance kit.
a. Take out the balance bag from the package box, use a balance clamp to select
one of the fan blades and clamp the balance clamp on the edge of the tail end
of the fan blade (Figure 22)
b. Turn on the fan switch to see whether the wobble of the ceiling fan has been
reduced. If it does not improve, try another fan blade. Experiment with all the
fan blades in turn to find the blade with the weakest clamping balance.
c. Clamp the balance clamp on the fan blade with the weakest wobble, move it
in or out on the edge of the fan blade, turn on the ceiling fan to find the best
position of the balance clamp to control the wobble balance (Figure 22)
d. Take the balance sticker, tear off the double-sided tape of the balance sticker,
and stick the balance sticker on the center of the blade at the position of the
balance clip (Figure 22)
1. Connect the live wire from ceiling to receiver black wire(AC IN L).
2. Connect the neutral wire from ceiling to receiver white wire(AC IN N)
3. Connect the Grey wire(Motor U) from motor to Grey wire(Motor U) from
receiver.
4. Connect the red wire(Motor V) from motor to red wire(Motor V) from receiver.
5. Connect the yellow (Motor W) from motor to yellow wire (Motor W) from
receiver.
6. Connect the blue wire(FOR LIGHT) from motor to blue wire (FOR LIGHT) from
receiver.
7. Connect the white wire(FOR LIGHT) from motor to white wire(FOR LIGHT)
from receiver.
X.
18
Balance piece
21
22
19 20