Winmate FM10A Installation and operation manual

Please read these instructions carefully before using this product, and save this manual for future use.
Winmate FM10A
Vehicle Mounted Computer
Android 6.0
Product Reference Guide
Version IV
9152111I101A
For more information on this
and other Winmate products,
please visit our website at:
www.winmate.com

- 2 -
Table of Contents
PREFACE ...............................................................................................................................................................- 4 -
READ ME FIRST .................................................................................................................................................... - 7 -
INFORMATIONS DE SÉCURITÉ(FR)...........................................................................................................................- 8-
SAFETY INFORMATION (EN)....................................................................................................................................- 8-
ABOUT THE ADAPTER............................................................................................................................................- 9-
LI-ION BATTERY .....................................................................................................................................................- 9-
INTRODUCTION...................................................................................................................................................- 10 -
ABOUT THIS GUIDE...............................................................................................................................................- 10 -
PACKAGE CONTENTS............................................................................................................................................- 11 -
OPTIONALACCESSORIES ......................................................................................................................................- 12 -
COMPONENTS ......................................................................................................................................................- 13 -
Front View .....................................................................................................................................................- 13 -
Rear View with VehicleDock.........................................................................................................................- 14 -
Top and Bottom View....................................................................................................................................- 14 -
Side View with VehicleDock .........................................................................................................................- 15 -
HARDWARE.........................................................................................................................................................- 16 -
SYSTEM HARDWARE.............................................................................................................................................- 16 -
CENTRAL PROCESSINGUNIT.................................................................................................................................- 16 -
INPUT AND OUTPUTCONNECTORS.........................................................................................................................- 16 -
SYSTEM MEMORY.................................................................................................................................................- 17 -
AUDIO INTERFACE ................................................................................................................................................- 17 -
MEMORY CARD ....................................................................................................................................................- 17 -
WWAN................................................................................................................................................................- 17 -
POWER................................................................................................................................................................- 17 -
Vehicle DC Power Supply.............................................................................................................................- 17 -
External AC Power Supply (Optional)...........................................................................................................- 17 -
POWER MANAGEMENT MODES..............................................................................................................................- 18 -
Full ON Mode ................................................................................................................................................- 18 -
Standby / Sleep Mode...................................................................................................................................- 18 -
Hibernate Mode.............................................................................................................................................- 18 -
OFF Mode.....................................................................................................................................................- 19 -
POWER CONTROL.................................................................................................................................................- 19 -
Power Switch.................................................................................................................................................- 19 -
Power Button.................................................................................................................................................- 19 -
IGNITION CONTROL...............................................................................................................................................- 19 -
BATTERY..............................................................................................................................................................- 20 -
UPS Battery...................................................................................................................................................- 20 -
Backup Battery..............................................................................................................................................- 21 -
EXTERNALCONNECTORS......................................................................................................................................- 22 -
Connector Pinouts.........................................................................................................................................- 22 -
CAN BUS CABLE INSTALLATION REFERENCE.........................................................................................................- 29 -
ANTENNACONNECTIONS.......................................................................................................................................- 30 -
Internal Wi-FiAntenna...................................................................................................................................- 30 -
External / Vehicle Remote Antenna...............................................................................................................- 31 -
KEYBOARD OPTIONS.............................................................................................................................................- 32 -
Integrated Keypad.........................................................................................................................................- 32 -
USB Keyboard / Mouse.................................................................................................................................- 32 -
LED FUNCTION ....................................................................................................................................................- 33 -
Connection and UPS battery LEDs...............................................................................................................- 33 -
System LEDs.................................................................................................................................................- 34 -
Power LED....................................................................................................................................................- 34 -
Touch Screen ................................................................................................................................................- 35 -
Display BacklightControl...............................................................................................................................- 35 -
SOFTWARE..........................................................................................................................................................- 36 -
INTRODUCTION.....................................................................................................................................................- 36 -
Operating System..........................................................................................................................................- 36 -
Android 6.0....................................................................................................................................................- 36 -
SETTING UP THE DEVICE.......................................................................................................................................- 36 -

- 3 -
Home Screen ................................................................................................................................................- 36 -
Quick Settings...............................................................................................................................................- 38 -
STATUS AND NOTIFICATION ICONS.........................................................................................................................- 39 -
Status Icons...................................................................................................................................................- 39 -
Notification Icons...........................................................................................................................................- 39 -
CONTROL PANEL..................................................................................................................................................- 40 -
Using the Touch Screen................................................................................................................................- 40 -
System Settings ............................................................................................................................................- 41 -
ETHERNET ...........................................................................................................................................................- 47 -
Configuring Ethernet Settings.......................................................................................................................- 48 -
Checking the Ethernet Settings.....................................................................................................................- 48 -
WINSET................................................................................................................................................................- 49 -
System Information .......................................................................................................................................- 49 -
Ignition Control..............................................................................................................................................- 50 -
Screen Blanking............................................................................................................................................- 51 -
Defroster (If Equipped)..................................................................................................................................- 52 -
Function Buttons ...........................................................................................................................................- 54 -
WINMATE®HOME MANAGER (WHM)....................................................................................................................- 56 -
How to Lock Applications..............................................................................................................................- 56 -
How to Reset WHM Settings.........................................................................................................................- 58 -
How to Change WHM Password...................................................................................................................- 60 -
BLUETOOTH .........................................................................................................................................................- 61 -
CONNECTING TO WI-FI NETWORKS .......................................................................................................................- 63 -
WWAN................................................................................................................................................................- 64 -
CAMERA FEATURES..............................................................................................................................................- 65 -
Taking Pictures..............................................................................................................................................- 65 -
Making Videos...............................................................................................................................................- 66 -
Camera Settings............................................................................................................................................- 67 -
SOFTWARE UPDATE .............................................................................................................................................- 68 -
Image Tool Download ...................................................................................................................................- 68 -
ACCESSORIES INSTALLATION.........................................................................................................................- 75 -
INSTALLING A SIMCARD.......................................................................................................................................- 75 -
INSTALLING A MICRO SDCARD .............................................................................................................................- 76 -
INSTALLING A STYLUS WITH THE HOLDER ...............................................................................................................- 77 -
VEHICLE MOUNTING..........................................................................................................................................- 78 -
INTRODUCTION.....................................................................................................................................................- 78 -
VEHICLE MOUNT INSTRUCTION..............................................................................................................................- 78 -
RAM MOUNT INSTALLATION..................................................................................................................................- 79 -
Mounting Kit 1 –No Drill Solution .................................................................................................................- 79 -
Mounting Kit 2 –Drill Solution.......................................................................................................................- 80 -
RAM Mount Assembly...................................................................................................................................- 81 -
Mounting Kit 3 –Keyboard Mounting Installation..........................................................................................- 82 -
DOCKING AND UNDOCKING THE DEVICE ................................................................................................................- 84 -
POWER CABLE INSTALLATION................................................................................................................................- 85 -
Wiring the Power Cable ................................................................................................................................- 85 -
Connecting the Power Cable for Testing ......................................................................................................- 85 -
Connecting the Power Cable for Installation on the Vehicle.........................................................................- 86 -
Power Cable Routing ....................................................................................................................................- 90 -
APPENDIX A: PRODUCT SPECIFICATIONS.....................................................................................................- 91 -
APPENDIX B: ORDER INFORMATION ..............................................................................................................- 93 -

FM10A Product Reference Guide Preface
- 4 -
Preface
Copyright © 2015 Winmate Communication Inc. All rightsreserved.
No part of this manual may be reproduce, copied, translated, or transmitted in any form or any means,
electronic or mechanical, for any purpose, without the written permission of Winmate Inc.
Trademarks
All product names, trademarks or logos mentioned herein are the properties of their respective owners.
Microsoft, Windows, and the Windows logo are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries. Microsoft products are licensed to OEMs by
Microsoft Licensing, Inc., a wholly owned subsidiary of MicrosoftCorporation.
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
All other brand and product names are trademarks or registered trademarks of their respectiveowners.
NOTE:
Display images shown may vary slightly from actual display. Information in this manual is
subject to change without prior notification.
NOTE :
FM10A Computer has to be used together with the docking station.
Use the device when located at least 20 cm (7.9 inches) away from the human body.
Disclaimer
Winmate Inc. reserves the right to make any product changes without notice, including circuits and/or
software described or contained in this manual in order to improve design and/or performance. Winmate
Inc. assumes no responsibility or liability for the use of the described product (s), conveys no license or
title under any patent, copyright, or masks work rights to these products, and makes no representations
or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this guide are for illustration purposes only.
Winmate Inc. makes no representation or warranty that such application will be suitable for the specified
use without further testing or modification.
Warranty
Winmate Inc. warrants that each of its products is free from material and workmanship defect for a
period of one year starting from the invoice date. If the customer discovers a defect, Winmate Inc. will, at
its option, repair or replace the defective product at no charge to the customer, provided it is returned
during the warranty period, with transportation charges prepaid. The returned product must be properly
packaged in its original packaging to obtain warrantyservice.

FM10A Product Reference Guide Preface
- 5 -
Advisory Conventions
Four types of advisories are used throughout the user manual to provide helpful information or to alert you to
the potential for hardware damage or personal injury. These are Notes, Important, Cautions, and Warnings.
The following is an example of each type of advisory.
NOTE:
A note is used to emphasize helpful information
IMPORTANT:
An important note indicates information that is important for you to know.
CAUTION/ ATTENTION
A Caution alert indicates potential damage to hardware and explains how to avoid the
potential problem.
Une alerte d’attention indique un dommage possible à l’équipement et explique comment
éviter le problème potentiel.
WARNING!/ AVERTISSEMENT!
An Electrical Shock Warning indicates the potential harm from electrical hazards and how
to avoid the potential problem.
Un Avertissement de Choc Électrique indique le potentiel de chocs sur des
emplacements électriques et comment éviter ces problèmes.
FCC Regulations
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s
authority to operate the equipment.
Operation on the 5.15-5.25GHz frequency band is restricted to indoor use only. The FCC requires indoor use
for the 5.15-5.25GHz band to reduce the potential for harmful interference to co-channel Mobile Satellite
Systems. Therefore, it will only transmit on the 5.25-5.35 GHz, 5.47-5.725 GHz and 5.725 –5.850 GHz band
when associated with an access point (AP).

FM10A Product Reference Guide Preface
- 6 -
CE Notice (European Union)
This device has been tested and found to conform to the limits set for a Class B product.
• EN 55022 —“Limits and Methods of Measurement of Radio Interference Characteristics of Information
Technology Equipment”
• EN 55024 —“Information technology equipment - Immunity characteristics - Limits and methods of
measurement”
• EN 61000-3-2 —“Electromagnetic compatibility (EMC) - Part 3: Limits - Section 2”
• EN 61000-3-3 —“Electromagnetic compatibility (EMC) - Part 3: Limits - Section 3”
• EN 60950 —“Safety of Information Technology Equipment”.
• EN 55022 Emissions requirements
RF Exposure Information (SAR)
This device is compliance with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1999
and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65
Supplement C.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
device was tested for operations with the device contacted directly to the human body to the back side of the EUT.
To maintain compliance with FCC RF exposure compliance requirements, avoid direct contact to the transmitted
antenna during transmitting.
IC Regulations
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.”
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the
Device.
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The device could automatically discontinue transmission in case of absence of information to transmit, or
operational failure. Note that this is not intended to prohibit transmission of control or signaling information or
the use of repetitive codes where required by the technology.
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to
co- channel mobile satellite systems; the maximum antenna gain permitted (for devices in the bands 5250-5350
MHz and 5470-5725 MHz) to comply with the e.i.r.p. limit; and The maximum antenna gain permitted (for
devices in the band 5725-5850 MHz) to comply with the e.i.r.p. limits specified for point-to-point and non-point-
to-point operation as appropriate, as stated in section A9.2(3). In addition, High-power radars are allocated as
primary users (meaning they have priority) of the band 5250-5350 MHz and this radar could cause interference
and/or damage to LE-LAN devices.
The County Code Selection feature is disabled for products marketed in the US/Canada. For product available
in the USA/ Canada markets, only channel 1~11 can be operated. Selection of other channels is not possible.
IC Radiation Exposure Statement
This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had
been tested in accordance with the measurement methods and procedures specified in IEEE 1528

FM10A Product Reference Guide Chapter 1 Read Me First
- 7 -
Read Me First
Follow and adhere to all warnings and instructions in this manual. For your safety, please read all safety and
operating instructions before using the product. Keep this manual for future reference.
ATTENTION: Pour réduire le risque d’incendie ou de choc électrique ne pas exposer l’appareil à la
pluie ou à l’humidité. VERIFIER que le cordon électrique est la prise murale pour un delai d’inactivite
prolongé. Pour arrêter complètement l’alimentation de l’appareil, débranchez le cordon d’alimentation
de la prise AC. N’enlever ni le capot arrière ni les pièces internes de l’appareil. Contactez un personnel
qualifié si nécessaire.
AVERTISSEMENT ÉLECTRIQUE
Utilisé pour les instructions destinés à alerter l’utilisateur d’un CHOC ÉLECTRIQUE
mortel ou de blessure grave en cas d’utilisation incorrecte de l’unité.
SA1965
AVERTISSEMENT
Utilisé pour les instructions destinés à alerter l’utilisateur d’un risque mortel ou de
blessure grave en cas d’utilisation incorrecte del’unité.
SA1966
ATTENTION: Pour réduire le risque d’incendie ou de choc electrique ne pas exposer l’appareil à la
pluie ou à l’humidité FAIRE le cordon électrique est DÉBRANCHÉ DE LAPRISE MURALE DANS UN
DELAI DE PROLONGER INACTIVITÉ. De se désengager totalement LE POUVOIR DE L’UNITE, S’IL
VOUS PLAÎT DEBRANCHER LE CORDON D’ALIMENTATION DE LA PRISEAC. NE PAS Romove le
capot arrière, pas de PIÈCES À L’INTÉRIEUR. Contactez un personnel qualifié S’il faut le réparer.
ELECTRIQUE AVERTISSEMENT
Sert aux instructions destin es alerter l’utilisateur d’un CHOC ÉLECTRIQUE mortel
ou de blessure grave en cas d’utilisation incorrecte de l’unit.
SA1965
AVERTISSEMENT
Sert aux instructions destin es alerter l’utilisateur d’un risque mortel ou de blessure
grave en cas d’utilisation incorrecte de l’unit .
SA1966
1

FM10A Product Reference Guide Chapter 1 Read Me First
- 8 -
Informations de sécurité (FR)
Suivez et respectez tous les avertissements et instructions figurant sur l’écran. Pour votre sécurité, s’il vous plaît lire
toutes les consignes de sécurité et de fonctionnement avant d’utiliser le device. Gardez ce manuel pour référence
future.
1. Lire avec attention toutes les recommandations et precautions d’emploi avant d’utiliser ce produit.
2. Veuillez conserver ces recommandations et précautions pour référence future.
3. Lire et comprendre tous les avertissements énumérés dans les précautions d’emploi.
4. Suivre toutesles précautions d’emploi pour utiliser ce produit.
5. Utiliser exclusivement un chiffon sec pour nettoyer ce produit.
6. Ne pas placer le produit près de toute source de chaeur telle que radiateurs, arrivées d’air chaud, fourneaux
ou autres appareils générant de la chaleur (incluant les amplificateurs producteurs de chaleur) .
7. Ne pas négliger la sécurité que procure un branchement polarisé ou avec raccordement à la terre, Un
branchement polarisé comprend deux fiches dont l’une est plus large que l’autre. Un branchement à la terre
comprend deux fiches plus une troisième reliée à la terre. Si la fiche secteur fournie ne s’insert pas dans votre
prise de courant. consulter un ‘électricien afin de remplacer votre prise obsolète.
8. Protéger le cordon d’alimentation de tout écrasement ou pincement, particulièrement au niveau des fiches, des
réceptacles utilisés et à l’endroit de sortie de l’appareil. Ne pas casser la fiche de terre du cordon
d’alimentation.
9. Utiliser uniquement les accessoires spécifiés par le constructeur.
10. Utilisez seulement des accessoires spécifiés par le manufacturier ou vendus avec le produit.
11. Débrancher cet appareil lors d’orages ou s’il n’est pas utilize pendant une longue période.
12. Faire exécuter le service par du personnel qualifié. Une intervention technique est requise lorsque l’appareil a
été endommagé ou n’opère pas normalement.
Safety Information (EN)
Follow and adhere to all warnings and instructions on the screen. For your safety, please read all safety and
operating instructions before using the device. Keep this manual for future reference.
1. Carefully read all recommendations and precautions for use before using this product.
2. Retain all recommendations and precautions for future reference as necessary.
3. Read and be sure to understand all warnings listed in the precautions.
4. Follow all operating precautions when using thisproduct.
5. Use only a dry cloth to clean this product.
6. Do not place the product near any heat sources such as radiators, warm air intakes, stoves or other heat-
generating devices (including amplifiers or other heat producing equipment).
7. Do not disregard the safety that a polarized or grounded connection can provide. A polarized connection
consists of two plugs, one of which is larger than the other. A grounded connection has two blades and a third
one that is grounded. If the main plug provided cannot be inserted into your outlet, consult an electrician to
replace your obsolete outlet.
8. Protect the power cord from being crushed or pinched, particularly in the area of the plugs, any receptacles
used, and the point of exit from the apparatus. Do not break off the ground pin of the power cord.
9. Use only accessories specified by the manufacturer.
10. Use only with accessories specified by the manufacturer or sold with the product.
11. Unplug this apparatus during lightning storms or when it is not being used for long periods.
12. Refer all servicing to qualified service personnel. A technical intervention is required when the apparatus has
been damaged in any way or does not operate normally.

FM10A Product Reference Guide Chapter 1 Read Me First
- 9 -
About the Adapter
• Use only the supplied AC adapter (Rating: Input DC 10-60V DC). Use of another type of AC adapter will resultin
malfunction and/or danger.
• Do not use the adapter in a high moisture environment. Never touch the adapter when your hands or feet are wet.
• Allow adequate ventilation around the adapter when using it to operate the device or charge the battery. Do not
cover the AC adapter with paper or other objects that will reduce cooling. Do not use the AC adapter while it is
inside a carrying case.
• Connect the adapter to a proper power source. The voltage requirements are found on the product case and/or
packaging.
• Do not use the adapter if the cord becomes damaged.
• Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is damaged or
exposed to excess moisture.
Li-Ion Battery
Your device has UPS battery. When disposing UPS battery, follow local rules and regulations.
WARNING!
Do not dispose the battery with general waste materials.
The following precautions on battery recycling should be observed:
The battery should be disposed properly according to local regulations;
The battery should not be damaged or crushed;
The battery should not be heated or exposed to direct sunlight.
If you are not aware of local regulations on disposing the battery pack, contact our Service Center or sales
representatives for more information.
IMPORTANT:
This hot-swap battery is soft-packed. It may have up to 8% inflation in dimensions under the usage in
normal conditions. The mechanical design of the device reserves the space for this normal inflation.
WARNING!
If you observe the internal hot-swap battery has been inflated more than normal condition (or the blotch
of panel and touch caused by inflated battery), contact our Service Center or sales representative for
replacing the battery immediately.
IMPORTANT:
The battery is consumable part. Therefore, it is recommended to replace the battery pack every two
years with a new one recommended by Winmate. Contact our Service Center or sales representatives
for more information on replacing the battery pack.

FM10A Product Reference Guide Chapter 2 Introduction
- 10 -
2
Introduction
In the warehouse environment, the ability to mount mobile devices and computers to forklifts, trucks, taggers, and
inventory pickers, is essential. From inventory management to order fulfillment, asset tracking, shipping and
receiving, the warehouse floor is complex ecosystem that requires high-efficiency technology to keep it running
smoothly.
The FM10A Vehicle-Mount Computer runs on a Freescale Cortex A9 i.MX6 Dual Core of the full Android 6.0 version.
The device features P-CAP multi-touch screen with 1024 x 768 pixel resolution. The FM10A Vehicle Computer
delivers flexibility and mobility in a vehicle mounted computer form factor. FM10A is designed to be easily removed
from the dock with a latch on the top of the FM10A vehicle docking. Since the dock remains attached to the vehicle,
this device can be easily moved or switched from one vehicle to another.
Integrated keyboard and physical function keys appeal to those who prefer the usability of a full keyboard, but in a
vehicle mounted computer form factor. For wireless connectivity the tablet comes equipped with Bluetooth 4.0 and
comprehensive 802.11a/b/g/n dual band Wi-Fi, and WWAN.
This vehicle-mount computer is built to endure the rigors of the warehouse, and designed to fit seamlessly into
forklifts and other warehouse vehicles.
NOTE:
Contact our technical support for information on the latest firmware upgrade for your device.
About This Guide
This Product Reference Guide provides instruction for the system administrator to follow when configuring and using
the FM10A Vehicle Mount Computer. This Product Reference Guide has been developed for a FM10A with Android
6.0 operating system.

FM10A Product Reference Guide Chapter 2 Introduction
- 11 -
Package Contents
Before using this device, make sure that all the items listed below are present in your package:
Computer FM10A
Dock + Latch Locking
Key
5 m Power Cable with Fuse
Kit
0.3 m USB Cable
USB to RS232 &
USB A Type Cable
98P010A000J7
98D000A0000A
98K000A0006O
9484098080K0
94E3098130K0
Cable Clamp Kit
Stylus Kit + Screw
Quick Start Guide
Driver CD
2 x Wi-Fi
Antenna
98K000A0005W
98K000A0005T
9152111I101B
9171111I102L
39700010000G
0.15 m Power
Converter Cable
84W Adapter with
power cable
External Antenna Fixing
Bracket
94J602G030K2
922D084W12V1
88111T201203

FM10A Product Reference Guide Chapter 2 Introduction
- 12 -
Optional Accessories
Your package may include the following items based on your order:
3 m DC Jack Power
Cable
1.2 m 120 Watt
Adapter
(For Heater Model)
4.2 m Adapter with
Power Cable
1.8 m RS232 Cable
0.3 m Audio Cable
94J0086020K0
92PO12120005
98K000A0006L
94G3094090K2
94E215R060K0
3 m USB to RS232
Cable
2 m IP65 LAN Cable
2 x Wi-Fi Antenna
15A, 250V, VDA
Type Fuses
Spare Key for
Vehicle Dock
94E3098130K0
94I0080080KF
39700000000H
94JL01L01000
9B000000007N
2 m GPS & LTE
Combo Antenna
(VM240)
5 m GPS & LTE
Combo Antenna
(VM9C)
5 m
GPS & LTE & Wi-Fi
Magnetic Combo
Antenna (VM10S)
Mounting Kit 1
No Drill
Mounting Kit 2
Drill
39700000000M
39700000000N
39700000000U
98K000A0005Y
98K000A0006P
Mounting Kit 3
Keyboard Mounting
1.8 m
CAN Bus Y Cable
98K000A0005X
94E2150090K0

FM10A Product Reference Guide Chapter 2 Introduction
- 13 -
Components
Front View
No
Item
Description
1
10.4” Touch Screen
Acts as one of the inputs for thedevice
2
Power Button
Press and hold the button for 3 second to turn on thedevice
Power Indicator
Power Indicator
3
Microphone
For voice communication and voice recording
4
Digital Microphone
For voice communication and voice recording
5
Camera
2 Megapixel front camera
6
Light Sensor
and LED
indicators
Light Sensor
HDD Indicators
Blanking Indicators
Heater Indicators
7
LED indicators
Wi-Fi Indicators
Bluetooth Indicators
UPS Battery Indicators
8
Label
Space to print the label or companylogo
9
Function button
Programmable Function key that can be configured by using the Win-Set ® Utility
10
Speaker
Emits Sound

FM10A Product Reference Guide Chapter 2 Introduction
- 14 -
Rear View with Vehicle Dock
No
Item
Description
1
VESA MountHole
VESA 75, 100, and RAM Mount
2
Release Latch
Press to release the device and thedocking
3
Kensington Lock
Connect to a security lock, protecting your device from beingstolen
4
Power switch
Set the switch to on (I) to provide the supply power to the device and it will
automatically connect to the ignition system of thevehicle
Top and Bottom View
No
Item
Description
1
Lock
Lock the tablet in place
2
Reading Light
Use to provide illumination in darkenvironment

FM10A Product Reference Guide Chapter 2 Introduction
- 15 -
Side View with Vehicle Dock
No
Item
Description
1
COM1 and COM2
Connects a peripheral device such as a printer or scanner with serialport
2
USB 2.0 x 2
Connects USB peripheral devices such as USB Flash drive, mouse,
keyboard, printer, etc.
3
*CAN Bus / Audio
Connects to a vehicle, allowing access to wide range of vehicle data
/ Connects headphone or other audio output devices
4
**Service Window
Toprotect I/O ports
5
LAN Port
Connects to a local area network (LAN) using an Ethernet cable and provide
optional POE with 48V
6
Wide Range Power Input
Connects a 10-60V DC IN wide range power input
7
WWAN AntennaConnector
Connects a WWAN external antenna and allows the device to be remotely
mounted on the vehicle
8
GPS Antenna Connector
Connects a GPS external antenna and allows the device to be remotely
mounted on the vehicle.
9
Wi-Fi Antenna Connector
Connects a Wi-Fi external antenna and allows the device to be remotely
mounted on the vehicle
*User can only select either COM port or CAN Bus.
**Service window covers SD Card Slot/ SIM Card Slot, USB3.0 and DC in power input jack.

FM10A Product Reference Guide Chapter 3 Hardware
- 16 -
3
Hardware
System Hardware
Central Processing Unit
The FM10A is running on Freescale Cortex A9 i.MX6 Dual Core processor, and Android 6.0 operating system.
Input and Output Connectors
The FM10A device supports the following I/O connectors:
•SIM Card Slot
•Micro SD Card Slot
•USB OTG
•DC In Power Input Jack.
The Vehicle Dock of the FM10A device supports the following I/O connectors:
•COM Ports
•CAN Bus / Audio
•LAN port
•Wide Range Power Input.

FM10A Product Reference Guide Chapter 3 Hardware
- 17 -
System Memory
The main system memory is 1GB LPDDR3.
Audio Interface
Your device is equipped with two speakers which are located on the bottom of the vehicle dock. A microphone is also
available for voice communication and voice recording.
As an alternative, you can use a headset adapter cable that provides a connection for headset operation. When
headset is plugged in to the adapter cable, the main speakers or internal microphone will be disabled.
Memory Card
Your device has a memory card slot which accepts an SD memory card. The memory card is hot swappable.
Your device has an 802.11 a/b/g/n/ac network card that can be used with internal or externalantennas.
WWAN
Using a SIM card for network connection, your device supports Wireless Wide Area Networking (WWAN).
Power
Vehicle DC Power Supply
The Power input voltage range for the vehicle dock is between 10 to 60V DC, without the need to perform any
manual operation within the vehicle dock.
This dock provides conditioned power output for the device. By using a specified DC to DC adapter, the input
voltage of 100-240 V DC nominal can be accepted.
External AC Power Supply (Optional)
If the DC power is not available, you can use an optional external UPS (Universal Input Power Supply) to convert
AC power to an appropriate DC level.
Using an external UPS and adapter cable, the AC to DC power input for the device is transferred to the vehicle
dock.
To perform the connection, simply plug one end of the adapter cable to the dock and then plug the other end of the
adapter cable to the DC output cable from adapter. For Details, refer to the connection diagram shown below:
No
Item
1
AC Input Cable
2
DC Output Cable
3
ToDC Output Cable
4
To FM10A

FM10A Product Reference Guide Chapter 3 Hardware
- 18 -
Power Management Modes
The FM10A has four power modes:
•Full ON
•Standby / Sleep
•Hibernate
•OFF
Action
Button
Power Button
Backlight
Indicator
Turn On
Press the On button for “2 seconds”
until the battery indicator On (solid
green) and then release the button
Off
Standby or
Sleep Mode *
Press the On button for “2 seconds”
until the screen On and then release
the button. The battery indicator will
Off after the screen is Off, the system
is already in the standby / sleep mode
On
Wake up
Press the On button for “2 second”
until the screen On and then release
the button. The battery indicator will
On (solid green)
Off
Turn Off
Press the On button for “4 second”
until the system is turns Off and then
releases the button.
Off
Full ON Mode
When the FM10A is attached to either vehicle power or an external power supply, or it is operating from the UPS
battery and the power button is pressed, the device is in the “ON” mode. In this mode, the keypad, touch screen
and any attached peripherals will function normally. The display remains ON until the display, standby or hibernate
timer expires.
When the device is in ON mode, the power LED indicators isoff.
Standby / Sleep Mode
When the Standby / Sleep timer expires without a primary event occurring, the device transitions to standby /
Sleep mode. Press the power button to wake up the device back to ONmode.
When the device is in Standby / Sleep mode, the power LED indicator isred.
Hibernate Mode
When the device is in Hibernate Mode, all LEDs are off. Press the power button to wake up the device back to ON
mode.
When the device is in Hibernate mode, the power LED indicator isred.

FM10A Product Reference Guide Chapter 3 Hardware
- 19 -
OFF Mode
By default, the FM10A turns off if the user turns off the device through the system or presses the power button for
8 seconds with a critical shut down. The FM10A will also be off when there is no connection to a power source or
the UPS battery is depleted. However the internal RTC will keep maintaining the date and time while the device is
off. When the device is off, the power LED indicator isred.
Power Control
Power Switch
Power switch is located on the rear side of the vehicle
dock. When the dock is connected to the external power
and the power switch is ON, the dock delivers power to
the FM10A and the device can be powered on.
Power Button
Power button is located at the lower right side of the
FM10A. If the device is OFF, pressing the power button
will start the power up sequence.
NOTE:
• The FM10A has to be docked in a powered vehicle docking station or UPS battery has to have a
sufficient charge to power the device.
• If no external power available and the UPS battery do not have enough charge, pressing the
power button will cause no action.
Ignition Control
The FM10A Vehicle Mount Computer has ignition control feature that enabled by software. For more details please
refer to Winset, Ignition Control section of this user guide.

FM10A Product Reference Guide Chapter 3 Hardware
- 20 -
Battery
Follow all the instructions in this user manual to prolong the battery life-cycle.
WARNING!
Recharge the battery pack according to the instructions in this user manual.
WARNING!
There is a risk of an explosion caused by incorrect installation or misapplication of the battery pack.
To avoid possible injury:
Use only the type of the battery recommended by Winmate.
Follow battery pack installation instructions in this user manual.
Keep the battery away from fire.
Store in a cool dry place.
Do not expose to heat, water and rain.
WARNING!
Do not drop, puncture, and crush the battery unit. If you notice any damages on the battery, stop
using the battery and replace it.
IMPORTANT:
When the battery level reaches 0%, the FM10A will automatically shut down.
UPS Battery
Your device has UPS battery. This UPS battery is automatically charged when the device is placed on a powered
dock. The charging time takes approximately 3hours. During full loading operations without external power attached,
the device uses UPS battery to operate.
When running on the UPS battery power, the power timeouts maybe different than when vehicle power is applied.
Using the UPS battery power, it allows the device to continue operation even when the device is not mounted in a
dock. The UPS battery is designed to supply power to your device for a minimum of 30 minutes.
IMPORTANT:
If the UPS battery power becomes critically low, the device will automatically hibernate to prevent
damage to the UPS battery;
To turn on the device using the UPS battery power, make sure the UPS battery has at least 10%
charge. If you cannot turn on the device, charge the UPS battery immediately;
The internal UPS battery status LED and the UPS battery control panel can be used to monitor the
status of the UPS battery.
IMPORTANT:
Charge the hot-swap battery together with main battery whenever your device is not being used/
charged for three months. Connect the device to the source of power for 1.5 hours to charge.