winsonic PCH21551-WH25L0-CB0J0G User manual

- Model #PCH21551-WH25L0-CB0J0G

Contents
Features
Safety Instruction
Introduction
Internal Jumpers and Connectors
3
4
4
Specifications 5
6

Safety Instruction
Read and follow these instructions when connecting and using your LCD monitor:
Operation:
1. Keep the monitor out of direct sunlight and away from stoves or any other heat
source.
2. Remove any object that could fall into ventilation holes or prevent proper cooling
of the monitor＇s electronics.
3. Do not block the ventilation holes on the cabinet.
4. When positioning the monitor, make sure the power plug and outlet are easily
accessible.
5. If turning off the monitor by detaching the power cable or DC power cord, wait
for seconds before attaching the power cable or DC power cord for normal
operation.
6. Do not subject the LCD monitor to severe vibration or high impact conditions
during operation.
7. Do not knock or drop the monitor during operation or transportation.
Maintenance:
8. To protect your display from possible damage, do not put excessive pressure on
the LCD panel. When moving your monitor, grasp the frame to lift; do not lift the
monitor by placing your hand or fingers on the LCD panel.
9. Unplug the monitor if you are not going to use it for an extensive period of time.
10. Unplug the monitor if you need to clean it with a slightly damp cloth. The screen
may be wiped with a dry cloth when the power is off. However, never use organic
solvent, such as, alcohol, or ammonia-based liquids to clean your monitor.
11. To avoid the risk of shock or permanent damage to the set, do not expose the
monitor to dust, rain, water, or excessive moisture environment.
12. If your monitor gets wet, wipe it with dry cloth as soon as possible.
13. If foreign substance or water gets in your monitor, please turn the power off
immediately and disconnect the power cord. Then, remove the foreign substance
or water, and send it to the maintenance center.
14. Do not store or use the LCD monitor in locations exposed to heat, direct sunlight
or extreme cold.
15. In order to maintain the best performance of your monitor and use it for a longer
lifetime, please use the monitor in a location that falls within the following
temperature and humidity ranges. Temperature: 5-35°C 41-95°F

Panel Cell Type / Glass Surface TFT LCD / Black Anti-Glare, low reflection coating
Aspect Ratio / Size Wide / 21.5" viewable diagonal area
Active Area / Pixel Pitch 476.64(H) x 268.11(V) mm / 0.248(H) x 0.248(V) mm
Native Resolution / Colors 1920(H) x 1080(V) / 16.7 M
Response Time
Light Source
System CPU
BIOS
System / Graphic Chipset
System Memory
HDD
I/O port
Expension
Power Power Input
Operating Condition Temperature / Humidity
Dimensions Physical Please refer to Drawing
Carton W x H x D = TBD
LED backlight, Long life, 35,000 hrs (typ)
0oC ~ 50oC (32oF ~ 122oF) , 10% ~ 90% (no condensation)
≤ 5 ms
Support for Intel® Core i7 / i5 / i3 / Celeron® (Skylake-S)
UEFI
Intel® H110
2 x DDR4 SO-DIMM slots, up to 32GB 2133MHz
4 x SATA2
1 x HDMI
4 x USB 3.0
1 x Display Port
1 x LAN, Mic-in, Line-out
1 x Mini PCI-e
12V / 19~24V DC-in (DC Jack / 4-pin ATX PWR Con)

MDH11KI Quick Reference Guide/ 快速测试参考指南
No. Code Descripon
1 FP_AUDIO Front audio header
2 SPKR Speaker cable connector
3 MIC_IN Audio Mic In port
4 LINE_OUT Audio Line Out port
5 USB3_2 USB 3.0 ports
6 USB3_1 USB 3.0 ports
7 TPM_LPC TPM connector
8 HDMI HDMI 2.0 port
9 DP Display port connector
10 LAN GbE LAN port
11 BATTERY Baery cable connector
12 CLR_CMOS Clear CMOS jumper
13 DC_IN DC In power connector
14 ATX_19V 2 pin power connector
15 FUSB2_5 USB 2.0 header
16 SATAIII_1 SATA 6Gb/s connector
17 SATAIII_0 SATA 6Gb/s connector
18 SATA_PWR Hard disk power connector
19 CPU_FAN CPU fan connector
20 SYS_PANEL Front panel header
21 MON_SW Monitor power switch header
22 SYS_FAN System fan connector
23 SODIMM2 DDR4 SO-DIMM slot#2
24 SODIMM1 DDR4 SO-DIMM slot#1
25 FPD_PWR LVDS power select jumper (12V/19V)
26 LVDS LVDS connector
27 FPD Flat Panel Display connector
28 BL_SW Back light brightness switch
29 LCD_VCC LVDS Drive voltage jumper
30 FUSB2_3 USB 2.0 header
31 CPU Intel LGA1151 socket
32 FUSB2_2 USB 2.0 header
33 FUSB2_4 USB 2.0 header
34 M2_E M.2 slot (PCIe Gen2 x1, Support NGFF-2230, E-Key)
35 COM1 Serial port header
36 M2_M M.2 slot (PCIe Gen2 x4 or SATA 6Gb/s
Support NGFF-2260/2280, M-Key)
37 DMIC_CON Digital Mic connector
3421 5 87 10 11
14
1312
15
16
17
22
19
20
21
2324
25
2829 26
27
303233
35
34
36
37
18
96
31
Front Panel Header/ 前面板
No. Pin Define
1 HDD LED+
2 Power LED+
3 HDD LED-
4 Power LED-
5 GND
6 Power Buon+
7 Reset Buon
8 Power Buon-
9 No Connect
10 No Pin
1
109
2
Power Connector/ 电源
2
1No. Pin Define
1 GND
2 19V
Installing CPU/ 安装 CPU
USB 2.0 Header
No. Pin Define
1 Power (5V)
2 Power (5V)
3 USB DX-
4 USB DY-
5 USB DX+
10
9
2
1No. Pin Define
1 VCC
2 USB-
3 USB+
4 GND
5 No Pin
15
5
1
No. Pin Define
6 USB DY+
7 GND
8 GND
9 No Pin
10 No Connect
1 9
102
Serial Port Cable Connector
No. Pin Define
1 NDCD-
2 NDSR-
3 NRXD-
4 NRTS-
5 NTXD-
No. Pin Define
6 NCTS-
7 NDTR-
8 5V
9 GND
10 No Connect
Memory Populaon Configuraon/ 安装内存
1
2
Rear I/O Connector/ 后面板接口
Off
State Description
Amber On 1Gbps data rate
Green On 100Mbps data rate
10Mbps data rate
10/100/1000 LAN LED:
Speed LED Link/Acvity
LED
No. Desripon
1 DC In power connector
2 GbE Eternet LAN port
3 Display port connector
4 HDMI 1.4 port
No. Desripon
5 USB 3.0 ports
6 Line Out port (Green)
7 Mic In port (Pink)
The HDMI connector is HDCP compliant and supports Dolby True HD and DTS HD
Master Audio formats. It also supports up to 192KHz/24bit 8-channel LPCM audio
output. You can use this port to connect your HDMI-supported monitor. The
maximum supported resoluon is 4096x2160@24Hz or 2560x1600@60Hz, but the
actual resoluons supported are dependent on the monitor being used.
SATA Connector/SATA 接口
1
7No. Pin Define
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
Hard disk power connectornnector
No. Pin Define
1 VCC3
2 VCC3
3 VCC3
4 GND
5 GND
6 GND
7 VCC
8 VCC
9 VCC
10 GND
1
N2 No. Pin Define
11 GND
12 GND
13 +12V
14 +12V
15 +12V
P1 GND
P2 GND
N1 GND
N2 GND
LVDS
No. Pin Define
1 +RXO3_C
2 -RXO3_C
3 +RXO2_C
4 -RXO2_C
5 +RXO1_C
6 -RXO1_C
7 +RXO0_C
8 -RXO0_C
9 +RXE3_C
10 -RXE3_C
401
No. Pin Define
11 +RXE2_C
12 -RXE2_C
13 +RXE1_C
14 -RXE1_C
15 +RXE0_C
16 -RXE0_C
17 GND
18 LCD_VCC
19 LCD_VCC
20 LCD_VCC
NOTE! Cable detect pin 24 must connect to ground.
No. Pin Define
21 No Connect
22 VCC3
23 GND
24 -Cable Detect
25 GND
26 +RXECLKO_C
27 -RXECLKO_C
28 GND
29 GND
30 GND
No. Pin Define
31 SMB_CLK_CON
32 SC_BKLT_EN
33 SC_BKLT_CTRL
34 +RXECLKE_C
35 -RXECLKE_C
36 FPD_19V
37 FPD_19V
38 FPD_19V
39 No Connect
40 SMB_DATA_CON
18
Flat Panel Display Connector
No. Pin Define
1 Backlight enable
2 Backlight control
3 Backlight inverter power
4 Backlight inverter power
5 GND
6 GND
7 Panel brightness increase
8 Panel brightness decrease
Front Audio Connector/ 前置音频
2
1
10
9No. Pin Define
1 MIC2_L
2 GND
3 MC2_R
4 FP_AUDIO_DET
5 LINE2_R
No. Pin Define
6 MIC2_JD
7 GND
8 No Pin
9 LINE2_L
10 LINE2_JD
Speaker Cable Connector
No. Pin Define
1 Speaker Out R-
2 Speaker Out R+
3 Speaker Out L+
4 Speaker Out L-
41
Back Light Switch Header
21
No. Pin Define
1 Back light down
2 Back light up
Baery Cable Connector
No. Pin Define
1 Baery+
2 GND
2 1
CPU/System FAN/ 风扇
1
1
4
4
No. Pin Define
1 GND
2 +12V
3 Sense
4 Speed Control
Monitor Power Switch
No. Pin Define
1 High/Low: turn on/off monitor
2 GND
2
1
Digital MIC In Connector
5
1
No. Pin Define
1 VCC
2 DMIC DATA
3 GND
4 DMIC CLK
5 No Pin
No. Desripon
1 Clear CMOS Jumper
Open: Normal operaon (Default seng)
Close: Clear CMOS data.
2 LVDS Back Light Power Select Jumper
1-2 Close: Set to 12V.
2-3 Close: Set to 19V. (Default seng)
3 LVDS Logic/LCD Drive Voltage Jumper
1-2 Close: Set to 3V.
2-3 Close: Set to 5V. (Default seng)
Jumper Sengs/ 跳线设置
23
1
1 2
3 4 76 5 5