Winsport Karella E-MASTER User manual

Instruction manual
Before use, please read the operating instructions carefully and keep it!
Karella
E-MASTER
Stand: 16. Mai 2019
E

Operating manual
2
8111.01 REV_DA_16052019
EE
CONGRATULATIONS FOR THE PURCHASE OF YOUR KARELLA DART MACHINE.
Before you mount device and use it, please read the following instructions first and keep it.
Only so you can use the device safe and with high reliability.
Familiarize yourselves in particular with the safety regulations.
IMPORTANT: The assembly may only be done by adults.
Use this device exclusively for the supposed purpose.
Technical advice:
If the power cord is connected to a socket, the unit is automatically powered. To operate the appliance,
please switch the main switch of the appliance to 'ON'.
Mains voltage: 110 - 240VAC / 50 Hz
Max. Power Consumption: 120 WMAX
Within the device there are no voltage potential which could endanger life, all of the circuits use a
voltage potential of 5 Volts or 12 Volts.
Dimension wall unit
Height: 97,5cm
Width: 62,0 cm
Depth: 46,5cm
Weight: approx. 45,0 kg
Dimensions base-underframe (optional)
Height: 210,0 cm
Width: 60,0 cm
Depth: 60,0 cm
Weight: approx. 8,0 kg
CAUTION: Electric shock due to cable damage –If you notice any visible damage to your E-
Master or power cord, do not use it.
Do not touch the cable until the plug has been disconnected from the socket.
Replace damaged cable completely.
It is forbidden to mend the defective cable with insulating tape. Repairs are only allowed by qualified
personnel.
Always route cables without tripping hazards and always choose extension cables long enough.
Cable must always be placed splash-proofed.
Never touch the mains plug and socket with wet hands. Only connect the device to AC power. The
specified voltage on the identification plate must match the voltage of the power source.
ATTENTION: PLEASE READ CAREFULLY PRIOR TO COMMENCING THE ASSEMBLY AND
USE OF THE UNIT.
It is not a toy! Danger for children –Choking hazard. Small parts.
With not appropriate use for article of every kind all guarantee claims go out!

Operating manual
3
8111.01 REV_DA_16052019
Please observe the following safety instructions to ensure a long life and optimal function of your
dartmachine:
(1) Do not try to open the unit by force. It contains no parts or components to which the user will be able to
repair. Consult a specially trained professional if there is a need for a repair.
(2) Slots and other openings on the top, sides, and bottom of the cabinet supports the ventilation system.
To ensure the unit is working properly and does not overheat, these openings must not be blocked or
covered.
(3) No sharp objects should be pushed through slots in the interior of the apparatus, as they could touch
live parts. It could cause a short circuit followed by a fire.
(4) The appliance must not be installed or located close to the heat source.
(5) No liquid may be poured over the apparatus. If this happens anyway, the device must be checked by a
specialist.
(6) Never expose the unit to rain or high humidity.
7) If you pass on the dartboard to another person, make sure that this person knows the contents of the
set-up and operating instructions.
(8) Before each use, you should check all parts for their function and should not use this device in the
case of faults occurring
CAUTION: Always unplug the power cord before cleaning the device.
CAUTION: Missing or modified safety devices.
Safety devices are for your protection. Never change or bypass safety devices.
ACCESSORIES & SPARE PARTS
Only use original accessories and original spare parts, they guarantee the safe and trouble-free operation of the
device. Information about accessories and spare parts can be obtained from your dealer.Li
DELIVERY
During unpacking, check the contents of the device for completeness. If there are no accessories included or
transport damages, please inform your dealer.
Winsport accepts no liability for damage that should be caused by disregarding these instructions.
We reserve the right to technical innovations or deviations in color and design.
Please keep the original packaging for possible later returns.

Operating manual
4
8111.01 REV_DA_16052019
Content
1. ASSEMBLY INSTRUCTIONS......................................................................................5
1.1. Wallmounting........................................................................................................................5
1.1. Mounting with stand (optional) ..............................................................................................6
1.2. Put up the start-line ad adjusting the height..........................................................................7
2. DETAILS AND STARTING UP....................................................................................8
2.1. Detail view of the device........................................................................................................8
2.2. Disassembly and maintenance of the dartboard...................................................................9
2.3. Start up.................................................................................................................................10
2.4. Delete credits.......................................................................................................................10
2.5. Keys...............................................................................Fehler! Textmarke nicht definiert.
2.6. Display .................................................................................................................................11
2.7. Coin validator.......................................................................................................................11
2.8. Overview..............................................................................................................................12
2.9. Testmenu.............................................................................................................................12
2.10. Sound...................................................................................................................................15
2.11. Main bookkeeping................................................................................................................15
2.12. Secundary bookkeeping......................................................................................................15
2.13. Turniermodus.......................................................................................................................16
2.14. Werkseinstellungen / Reset.................................................................................................16
2.15. Setup Menu..........................................................................................................................17
2.16. Sound Volume adjust...........................................................................................................21
3. GAME RULES...........................................................................................................22
Attention: The manual is intellectual property of Winsport e.K. Reproduction of the entire manual or individual
passages is only permitted with the written permission of Winsport.

Operating manual
5
8111.01 REV_DA_16052019
1. Assembly Instructions
Please read the instructions carefully before you start assembling! Always mount the dartboard with at least two
adults!
!
1.1. Wallmounting
Step 1
Open the device and remove the accessory set.
Loosen the safety screw and remove the Wall bracket from
the back of the device.
Step 2
Attach the wall bracket with the supplied our dowels (Ф 8 mm)
and screws (6 x 50 mm) on the wall. The position of the drill
holes can be found in the sketch beside.
Step 3
ATTENTION: Please carry out this procedure with
two peoples –never alone!
Hang the device in the wall bracket and fix the device with the
safety screw on the wall bracket.
Stept 4
After the device has been properly installed, the device can be
connected to the power supply.
ATTENTION: The power cable must not cause tripping hazards.
Always use appropriate cable extensions, if the distance to the socket
should be too big!
Note: 2 people needed to
mount the device.

Operating manual
6
8111.01 REV_DA_16052019
1.1. Mounting with stand (optional)
ATTENTION: For safety reasons, it is absolutely necessary to secure the unit against
falling over by attaching it to the floor or wall.
Step 1
Open the device and remove the accessory set.
Loosen the safety screw and remove the Wall bracket from
the back of the device.
Step 2
Take the two lower parts # 1 and connect them to the cross brace # 2. Use the supplied screws and nuts for this.
Step 3
Now insert the upper part # 3 on the two cross-beams and screw them together with the screws and nuts
provided.
ATTENTION: Before you hang up the device to the stand-foot,
make sure that the device stands on his final place.
Step 4
ATTENTION: Please carry out this procedure with two people
–never allone!
Hang the device in the holder of the stand and secure the device to the pedestal-bracket with the safety screw.
To ensure a secure footing, place the device on a firm and level floor, so that the device is in the balance.
Step 5
After the device has been properly installed, the device can be connected
to the power supply.
ATTENTION: The power cable must not cause tripping hazards.
Always use appropriate cable extensions, if the distance to the socket
should be too big!
Note: 2 people neede to
mount the device.

Operating manual
7
8111.01 REV_DA_16052019
1.2. Put up the start-line ad adjusting the height
High of the Bull’s Eye: The distance from the Bull's Eye to the ground should be 1.73m.
2.
The distances are additionally marked in the
enclosed measure-tape, so that a correct
installation is facilitated.
Start-line: The distance between the throw-off line
and Bull's Eye (not the wall!) should be 2.37m on
the ground or 2.93m diagonal from the startline.
Bull´s Eye
Start-line

Operating manual
8
8111.01 REV_DA_16052019
Details and Starting up
2.1. Detail view of the device
The illustration below shows the inside of the dart machine. The maintenance of the device and the cleaning or
replacement of the dartboard are very simple and can be done by yourself.
Wooden support for the dartboard
Winged nuts holding the dartboard
Matrix field connector
Slot unit
CPU board
Speaker
LED Light
Counters
Supply
Infra sensor
Missed arrows Sensor

Operating manual
9
8111.01 REV_DA_16052019
2.2. Disassembly and maintenance of the dartboard
After a few thousand games broken arrow points could fill in or clog dartboard segments, resulting the arrows not
being able to stick on the dartboard. Then it is time to clean the dartboard. The broken tips can be removed with
the help of pliers, whereby those who cannot be pulled out with the pliers can push into the interior of the
segment. Then the dartboard has to be disassembled to be able to remove the pressed-in tips.
WARNING: Careless and incautious handling of the dartboard and its parts can cause damage and
provoke damage to the dartboard or its parts. To safely disassemble the dartboard follow the exact
sequence of the steps below.
.
Step by step disassembling the dartboard:
1. Turn off the device, open upper door and disconnect the sensor field connector on
the electronics board (see detail view 2.1.);
2. Unwind 4 wing nuts (see detail view 2.1.) and take out the dartboard to the front from its base;
3. Unwind 4 wing nuts from the rear side of the dartboard and remove the wooden base;
4. Carefully unwind the two screws from the sensor field and remove the sensor field and protective rubber;
5. Remove the broken tips and assemble the dartboard board to the opposite side;
6. After every disassembly and assembly it is important to check the sensor field function (test target, see chapter
5.1.1.).
Wood
Sensor
field
Rubber
Segments
Spider
Screws
Wood
Null sector

Operating manual
10
8111.01 REV_DA_16052019
2.3. Start up
When switched on, a start melody sounds. Before the device jumps into the demo mode, the device checks
whether there are clamping buttons. If a jammed key is found, "KEY BLK" will appear in the display and a warning
tone will sound
The device has a RAM memory where the last game is saved. Should be e.g. due to a power failure, the device
will be switched off during operation (for example, power failure), the last game can be continued after restarting
the device. Any existing credits are also saved.
If you throw on the dartboard without a valid credit, an alarm will sound - unless the device is in tournament mode.
2.4. Delete credits
To clear the credits, open the unit with the key, set DIP microswitch 5 (detailed explanation of the DIP
microswitches in Chapter 3) to ON, and press the player change button for a few seconds. Then set the
microswitch back to OFF.
2.5. Buttons
For those buttons that have multiple functions, pressing the keys changes the game (for example, you have to
press the key 3 times for game 501). In addition, the name of the game appears on the display. After selecting a
game, the option keys flash. These can be selected until the game starts, even if the lights on the keys stop
flashing. The selected option of the game will appear on the display.
180,301
501,701
901 Parcheesi Double In
Cut Throat
Cricket Double
Out Master Out Team
Abort game
Button change player