WiSilica lumos controls Catron V User manual

Wireless 5 Button Remote
Catron V
WARNING AND GUIDELINES!!!
DO NOT INSTALL DAMAGED PRODUCT! This product has been properly packed so that
no parts should have been damaged during transit. Inspect to confirm. Any part
damaged or broken during or after assembly should be replaced.
REQUIRED TOOLS & SUPPLIES
INSTALLATION INSTRUCTIONS
INSTALLATION STEPS
Read and follow all safety instructions!!
Catron V Screwdriver Screws Wall plates
Find a suitable place to fix the wall bracket using screws.
Using a level and a pencil, lightly mark 2 small dots to align the top edge
of the mounting plate.
Mark the mounting screw drill points and drill holes for the wall anchors
with a 3/16” drill bit and insert wall anchors.
Insert the top screw(s) loosely and level the back plate.
Insert the bottom screw(s), and then hand tighten the top screw(s).
Attach the wall plate on top of the rocker pad using the two screw holes.
Ensure the switch is within BLE range of other system components
Pick a convenient location, perhaps near a door where occupants enter
and exit
Consider the construction materials in the space and remove the
obstacles that may interfere with RF signals
Specifications Value Remarks
Input voltage
Frequency range
CR 2032 battery3VDC
2402-2480MHz
7dBm
0 to 50°C (32 to 122°F)
-10 to 60°C (14 to 140°F )
95%
-92dBm
4.1 X 1.6 X 0.47in (105 X 40 X 12mm)
Tx power
_
Conductive
_
_
Non-condensing
L x W x H
Operating temperature
Storage temperature
Relative humidity
Receive sensitivity
Dimension
_
INSTALLATION AND QUICK START SHEET
PRODUCT OVERVIEW
Catron V is a battery-powered switch that
configures ON/OFF, intensity, and Correlated
Color Temperature of an individual or group of
luminaires.
This compact device is designed for maximum
longevity.
It is part of Lumos Controls ecosystem, which
includes controllers, sensors, switches, modules,
drivers, gateways, and analytical dashboards.
Do not disassemble the product
WARNING: Risk of Product Damage
I.
II.
III.
IV.
V.
VI.
Do’s
Installation should be performed by a
qualified electrician
Don'ts
Don't use outdoors
Installation shall be in accordance with
all applicable local and NEC codes Don't dissemble the products
Place devices as far away as possible
from metallic materials and also do
not place the device inside a metallic
box
Devices work best in when there is a
clear LOS between them
Delete the switch from the App only when
The controllers are in powered ON state
Switch and controllers are in BLE range

Intensity(dimming) of
the luminaires can be
controlled using
these intensity up
and down buttons
A single click on the
Up and Down
buttons will increase
or decrease the
intensity by 10%
CCT operation can be
performed by clicking the CCT
mode button
The device will persist in CCT
mode only for 10 seconds after
the click
While in the CCT mode the CCT
up and down buttons can be
used to increase or decrease
the CCT by 10%
Intensity
Down
Intensity
Up
CCT Down
CCT Mode
CCT Up
Intensity Operation CCT Operation
5-year limited warranty
Please find warranty terms and conditions
Note: Specifications may change without notice
Actual performance can vary due to end-user environment and application
WARRANTY
Please visit Help center
for more details
Once powered up, the device will be ready to be commissioned via the Lumos Controls mobile
app, available for free download on iOS and Android. To begin commissioning, click the ‘+’
icon from the top of the ‘Devices’ tab. The app allows you to preset certain configurations
which will be loaded after the device is added. The pre-configurations made using
'Commissioning Settings' will be sent to the devices being commissioned.
Once commissioned, the device will be displayed in the ‘Devices’ tab and you can perform
individual operations like ON/OFF/dimming on it from this tab.
Note: The ‘Output Channel Configuration’ will be ‘Single Channel’ by default. To configure dual
channel settings, go to ‘Additional Settings’ and click ‘Output Channel Settings’. Then select
‘Controller based color tuning’ or ‘Driver based color tuning’ based on the connected driver.
COMMISSIONING
LUMOS CONTROLS
APPLICATION
Download the ‘Lumos Controls’ application
from Play Store or App Store
OR
Scan the QR codes to download the
‘Lumos Controls’ application
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by WiSilica Inc. is under license. Other trademarks and trade names are those of their respective owners.
All Rights Reserved WiSilica Inc
www.lumoscontrols.com
20321 Lake Forest Dr D6,
Lake Forest, CA 92630
[phone]
Ver 1.1 Mar 2023
Long press the ON and OFF
button simultaneously for
10 seconds to activate
commissioning mode
A LED would lit up when
the device is under the
commissioning mode
ON and OFF buttons
can be used to perform
ON-OFF operations
ON
OFF
ON/OFF Operation
Commissioning
DEVICE CONTROLS
Problem Solution Checklist
TROUBLESHOOTING
The rocker pad does not
generate a message
Verify the rocker pad is installed in the
proper orientation
The linked device does not
respond to wireless
messages
Check for environment or range issues
Check if appropriate devices are linked