WisyCom MCR42 User manual

Wisycom Srl Unipersonale - Via Spin, 156 - I-36060 Romano d’Ezzelino (VI) -Italy
tel. [phone] fax. [phone] http:// www.wisycom.com -e-mail: [email protected]
Iscrizione al Registro A.E.E. n. IT09100000006319
Subject to change without notice
MCR42 WIDEBAND DUAL TRUE DIVERSITY ENG RECEIVER
HIGH PERFORMANCE DUAL TRUE DIVERSITY RECEIVER - DIGITAL AUDIO DSP BASED
Main Features
Up to 240 MHz bandwidth in 470/798 MHz range
Modular stand-alone or slot-in format
40 groups of 60 frequencies fully user programmable
Broadcast superlative quality of any audio-signal transposition
DSP fully digital audio processing f or broadcast superlative quality
and multicompander compatibility
Infrared interface for programming and transmitter synchronization
Easy setup and operation thru a OLED display
Wisycom exclusive digital sub-carrier telemetry technology
allows:
remote TX battery monitoring
advanced tone-squelch operating
PTT function (An optional back-panel module is available, with the
secondary intercom output)
Exceptional sturdiness and absolute reliability even in very congested
environments
Amazing small size
Very easy and pleasant use with easy status indication by means of
RGB LEDs
GENERAL DESCRIPTION
MCR42 is a camera dual true diversity wireless-microphone receiver system in a modular stand-alone or slot-in
configuration (compatible with most camera’s slot).

camera “slot-in” receiver (for Ikegamy, Philips, Sony cameras)
camera “stand-alone” very small dual true-diversity receiver,
powered by 5 ÷ 18 Vdc external source
All audio processing is managed by a powerful DSP to allow multicompanding, audio enhancement and a digital
control data.
Very easy and versatile thanks to its:
Oled display,
navigation button controls,
infrared sinc and programming,
automatic scan.
 Wider Oled Display!
 Optimized button layout!
 Simplified software!

Wisycom Srl Unipersonale - Via Spin, 156 - I-36060 Romano d’Ezzelino (VI) -Italy
tel. [phone] fax. [phone] http:// www.wisycom.com -e-mail: [email protected]
Iscrizione al Registro A.E.E. n. IT09100000006319
Subject to change without notice
MCR42 WIDEBAND DUAL TRUE DIVERSITY ENG RECEIVER
TECHNICAL DATA
• Frequency range [1]
:
MCR42 N ⇒option 470 ÷ 700 MHz
MCR42 M ⇒option 566 ÷ 798 MHz
• Switchable channels
:
40 groups of 60 channels fully user progr.
• Switching-window
:
up 240 MHz [1].
• Frequencies
:
microprocessor controlled frequency synthesizer circuit, with 25 kHz minimum step. The frequencies is
easily PC reprogrammed with the optional UPK 300E Programming Kit.
• Frequency error
:
< ± 2.5 ppm, in the rated temperature range
•Temperature range
:
-10 ÷ +55 °C
• Modulation
:
FM, with 50 μs de-emphasis.
• Nominal deviation
:
±40 kHz (Max. operating dev. = ± 60 kHz).
• “A” / “B” antenna inputs
:
with sturdy connectors.
• Antenna input
impedance
:
50 ohm sma type (SWR < 1:2; typ. 1:1.4).
• Sensitivity
:
⇒2 μV ( 6 dBμV), for SND/N > 58 dB;
⇒5 μV (14 dBμV), for SND/N > 98 dB.
in the whole switching-window [2].
• Amplitude response
:
< 0.5 dB (RF input sig.:6 dBμV ÷ 100 dBμV).
• Co-channel rejection
:
> 2.5 dB.
• Adjacent chan.
selectivity
:
> 80 dB typical (for ch. spacing ≥ 400 kHz).
• Spurious rec. rejection
:
> 100 dB.
• IF image rejection
:
> 90 dB.
• Intermod. rejection
:
> 76 dB.
• IIP3
:
> +10 dBm typical.
• Spurious emissions
:
< 2 nW (typical = 0.1 pW).
• Noise Reduction system
:
ENR (Wisycom Extended-NR) , noise optimized
ENC (Wisycom Extended-NC), voice optimized & with reduced pre-emphasis
⇒Others, compatible with most systems, thru an internal DSP emulation of SA572, SA575 and Rms
envelope compander chip set, fully user programmable
• AF bandwidth
:
30 Hz ÷ 20 kHz.
• Frequency response
:
± 0.5 dB in the 30 Hz ÷ 19 kHz range.
• Distortion
:
0.3 % typical.
• SND/D ratio (Analogue)
:
110 dB typical [2]
• SND/D ratio (AES3)
:
>125 dB typical [2]
• POWER LEDs
:
1 multicolour RGB LEDs to easy indicate Rx1 & Rx2 power status:
- GREEN/PALE GREEN if "Receivers ON" with external power supply/battery;
- GREEN blinking/PALE GREEN blinking if low power supply/ low battery level
- RED blinking indicates power supply status of transmitter:
slow blinking, at 25% battery capacity;
fast blinking, at 12.5% battery capacity.
• RF LEDs
:
2 multicolour RGB LEDs to easy indicates Rx1 & Rx2 RF status. Always on in normal operation:
- RED, if both receivers RF level is under squelch level;
- GREEN, if signal above squelch level & antenna A (green) is active;
- BLUE, if signal above squelch level & antenna B (blue) is active;
- YELLOW, if signal above squelch and both antenna are used.
• AUDIO LEDs
:
2 multicolour RGB LEDs to easy indicates Rx1 & Rx2 audio status:
- RED, if audio is muted cause of squelch (or tone squelch if active);
- GREEN, if audio is active and tone squelch present;
- BLUE, if audio is active and tone squelch not present.
• Front buttons
:
simple operation with 4 buttons to quickly monitor and setup the receiver.
One touch function for a frequency scan and sync function.
• Powering
:
- External = 5 ÷ 18 Vdc (1.5 W max).
- Autonomous. = with optional BCA 42 Battery Module
(5 x IEC-LR6 1.5V size-AA alkaline or rechargeable elements).
• Dimensions
:
“Slot-in” execution= 68 x 18 x 115 mm, “Stand-alone” exec. = 68 x 18 x 135 mm.
• Weight
:
180 g approx.
Analogue Audio Output
• Audio line-output 1 & 2 : electronically balanced on two 3 pin mini-XLR Female connector
• Audio line-output level : Adjustable in a one dB step between: -20 and +6 dBu (nominal) and MAX +12 dBu (peak deviation)
• Audio line-output imped. :≤ 200 ohm.
Push to Talk (PTT) Audio Output
• PTT line-output 1 & 2 : electronically balanced on a 5 pin mini-XLR Male connector
Digital Audio Output
• Digital line-output 1 & 2 : electronically balanced on 3 pin mini-XLR Male connector
• Digital line-output : AES3 @ 48 kHz
NOTE [1]: Extended limits or other custom ranges are available on request,
if allowed by your country-specific regulation.
NOTE [2]: RMS value, 22 Hz / 22 kHz, unweight.
The MCR 42 receiver complies with ETSI specifications: ETS 300 422.

Wisycom Srl Unipersonale - Via Spin, 156 - I-36060 Romano d’Ezzelino (VI) -Italy
tel. [phone] fax. [phone] http:// www.wisycom.com -e-mail: [email protected]
Iscrizione al Registro A.E.E. n. IT09100000006319
Subject to change without notice
MCR42 WIDEBAND DUAL TRUE DIVERSITY ENG RECEIVER
TOP FEED OPTIONS & SLOT IN - ACCESSORIES
MCR42 has 4 main audio sources:
Audio Line 1&2
AES3 (audio 1&2, 48kHz 24bit)
PTT (push to talk) 1&2
Headphone(left/right)
Top feed can bring on top on a mini-XLR 5M connector two balanced audio called line1 and line2.
MCR42-Exx can then be in factory configure to connect on top (line 1 & 2) the audio source you need.

SLOT-IN KIT
CAM50-3
CAM50-41
CAM50-42
Line 1 to XLR
Line 2 to XLR
Line 1 & 2 to XLR
MCR42-EL2: Audio Line 1 & 2
MCR42-ELC: Audio Line 1 & PTT Line 2
MCR42-EC2: PTT Line 1 & 2
MCR42-ECL: PTT Line 1 & Audio Line 2
SLK42-IK
SLK42-PH
SLK42-SX
IKEGAMI/PANASONIC
GRASS VALLEY
SONY
MCR42-Exx

Wisycom Srl Unipersonale - Via Spin, 156 - I-36060 Romano d’Ezzelino (VI) -Italy
tel. [phone] fax. [phone] http:// www.wisycom.com -e-mail: [email protected]
Iscrizione al Registro A.E.E. n. IT09100000006319
Subject to change without notice
MCR42 WIDEBAND DUAL TRUE DIVERSITY ENG RECEIVER
c
STAND-ALONE –ACCESSORIES
With the standalone socket BPA42-PTT and BPA42-HPN is available the option OP-BPA42-R22 to have an attenuation of -22dB in Line 1
and Line 2 outputs.
NOTE: With this option, it’s not possible to use the AES3 output in the standalone socket and it’s not guaranteed the correct functionality
of the AES3 output in the top feed.
FLA42
BCA42
MCR42
BPA42-HPN
BPA42-PTT
CAM50-2
CAM50-2
CDC34
CAM50-3
Power (Hirose)
PTT out 1 & 2
Headphone
Line out 2
Line out 1 / AES3
Back Panel
Batt. pack
5AA
BPA42BAG
Line out 1 / AES3
Line out 2
Power

Wisycom Srl Unipersonale - Via Spin, 156 - I-36060 Romano d’Ezzelino (VI) -Italy
tel. [phone] fax. [phone] http:// www.wisycom.com -e-mail: [email protected]
Iscrizione al Registro A.E.E. n. IT09100000006319
Subject to change without notice
MCR42 WIDEBAND DUAL TRUE DIVERSITY ENG RECEIVER