WisyCom BFLR1 User manual

QUICK USER GUIDEQUICK USER GUIDE
WISYCOM INC.
14301 Sullyeld Circle, Suite C
Chantilly, VA 20151- USA
[phone]
[email protected]
[email protected]
This guide is intended to assist you with initial quick setup and
operation for your Wisycom product.
You can refer to Wisycom Authorized Distributors for technical
support and information about service and repairs available in your
region or contact us directly by email.
Serial Number: Purchase Date:
WISYCOM S.r.l.
Via Tiepolo 7/E
35019 Tombolo (PD) - ITALY
[phone]
[email protected]
[email protected]
Download Documentation and Firmware
Get declaration, user manual, tips, software,
specications, on the download page:
wisycom.com/products/d/bt1-br1/
Keep up with Wisycom online
Follow us on Facebook and Instagram. You
can also subscribe on Youtube for more.
wisycom.com/social
Product Registration and Warranty
Register your product to extend your warranty
and receive updates on latest rmware:
wisycom.com/products/my-account
BFLR1-en-q01#ISTR-BFLR1
BFLR1 BFLR1
IC
Safety EN62368-1:2014; EMC: ETSI EN 300 386 V1.6.1 (2012-04) and FCC CFR-47 part 15 Sub part B
Conformity
Main Accesories (for an updated and full list, visit wisycom.com)
PAW: Wideband Antenna Amplier (for BFLR1 in
IFB mode)
LBP: Directional antenna with amplier (for
BFLR1 in IFB mode)
PSP15V1A2: 90-264 Vac power supply with
Hirose 4 pin connector (15VDC 1.2mA)
Supplied with EU/UK/USA/AU plugs
ABTS: Bluetooth antenna
ADFC: FC/APC adapter (to upgrade BFL optical
connector from SC/APC to FC/APC)
ADST: ST/APC adapter (to upgrade BFL optical
connector from SC/APC to ST/APC)
CNGA26: N connector (to upgrade RF connec-
tor from BNC to N)

21G BFLx1 QUICK MANUAL
RF OUT
9~18 Vdc
BT
RX
OPT
IN
RX
RF INBT
TX
OPT
9~18 Vdc
OUT
TX
Menu Button
Press this button to enter the main
menu and select menu options.
Press to SAVE.
FIBER TIPS BOX
• Clean your ber connectors on both ends
• Use single mode ber only
• Be sure your ber connectors are APC
• Typical ber loss with Wisycom systems
is approx. 0.4 dB/Km
• Optical PWR working range 0.3mW-4mW
Up
Short Press to scroll up in the main menu
or to access the rotary quick menu.
Down
Short Press to scroll down in the main
menu or to access the rotary quick menu.
Exit Button
Press this button to step back
while in the main menu.
RF Connector
BNC connector for RF output. If used with active
antennas (e.g. LBP) enable the booster by BFL
settings menu Boost (12 VDC @ 150mA max).
N connector is available for user upgrade.
BFL name
Received
Optical Level
Bluetooth Connector
SMA connector for BT
antennas to remotely
control via Wisycom BT
(iOS/Android app).
Optical Connector
SC/APC (others on request)
ST and FC connectors are
available for user upgrade.
Power Connector
Hirose power connector 9-18 VDC
type HR10A-7R-4S (pin1: GND, pin4: VDC)
(consumption 2.5 W with booster & 1.5 W without).
Red: RF alarm (Antenna fault)
Grey: Bluetooth off
Blue: Bluetooth on
Red: link alarm (optical PWR out of range)
Green: laser on
Grey: laser off
Link Status Led Bluetooth Status and RF alarm Led
Antenna booster status
(IFB mode only)
Bluetooth enabled icon
Mode
• ANT operating in reception (wireless microphone)
• IFB operating in transmission (IEM / IFB remoting)
Gain level
21G BFLx1 QUICK MANUAL
RF OUT
9 ~ 18 Vdc
BT
RX
OPT
IN
RX
LASER 1M
RF INBT
TX
OPT
9 ~ 18 Vdc
OUT
TX
21G BFLx1 QUICK MANUAL
RF OUT
9 ~ 18 Vdc
BT
RX
OPT
IN
RX
LASER 1M
RF INBT
TX
OPT
9 ~ 18 Vdc
OUT
TX