Witura WT-1018 User manual
GSM Fixed Wireless Terminal
WT-1018
User’s Manual
WT-1018 GSM Fixed Wireless Terminal___________________________________
2
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
Contents
Main Features……………………………………………………………………………………………...….3
Caution…………………………………………………………………………………………………......…3
Storage………………………………………………………………………………………………………...3
Sketch of Fixed Wireless Terminal……………………………………………………………………..…….4
Installing SIM Card…………………………………………………………………………………………...5
Setting up the Terminal…..…………………………………………………………………………………...5
Installation for connecting to register cost equipment………………………………………………………..5
Turn on and Turn off Wireless Terminal…………………………………………………………………......6
Making Calls and Answering Incoming Calls………………………………………………………………..6
Programming Code Settings…………………………………………………………………………...……..7
Technical Specification………………………………………………………………………………….……9
Troubleshooting………………………………………………………………………………………….…..10
WT-1018 GSM Fixed Wireless Terminal___________________________________
3
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
Main Features
•Adopt advanced microprocessor controlling circuit, run steadily. Capability is ascendant
•Adopt high gains antenna. Signal is strong
•Be applicable for GSM900MHz/DCS1800MHz/PCS 1900MHz
•Call or called function can be set up flexibly
•The functions of locking terminal, locking SIM card, locking network and locking cell can be set up
conveniently.
•Function of displaying incoming calls.
•Provide accurate anti-polarity signal for billing equipment to charge
Caution:
1. This terminal should not be used at garage, oil storage and chemical plant or near to flammable or
explosive substance.
2. This terminal should be avoided in the hospital. It will interfere medical electronic equipments such as
pacemaker and audiphones. This terminal could only be used indoors.
3. If it is found that the terminal is not successful in login onto the network, please check whether the SIM
card and antenna are installed well or not.
4. Don’t use the SIM card that has been used in this terminal to other device. Please make sure the initial
PIN code of SIM card is 1234 and disabled when installing SIM card.
5. It is forbidden to touch the antenna when the connected telephone is being used. (being making calls or
receiving calls), otherwise the terminal will be damaged. This kind of damage is beyond the range of
warranty.
6. When the terminal is using, it should be placed where the signal of network is strong enough. In order
to ensure the quality of call voice, the terminal should be far from other electronic equipment.
7. The terminal does not identify SIM card of 5V and 1.8V, only identify 3V SIM card.
8. Don’t disassemble the terminal by yourself. If there is any problem, please contract the authorized
personnel.
9. Working voltage of wireless terminal ranges from 6.0V to 7.5V.
Storage
1. Terminal that is packed or not should piled up no more than 10 layers.
2. The terminal should be saved in ventilate and dry place.
3. Don’t knock terminal to avoid breaking the case.
4. Don’t use chemic impregnate to clean terminal, but use dry soft cloth to make it clean.
WT-1018 GSM Fixed Wireless Terminal___________________________________
4
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
Sketch of the Fixed Wireless Terminal
The WT-1018 Fixed Wireless Terminal
Frontal view
LED indicators
LED1 - Power indicator (it’s lit while power source is connected correctly)
LED1 - Signal indicator (Flashing once in one second indicates that the terminal is on GSM network.
Being lit for a long time indicates that the terminal has failed to login onto GSM network)
Back view
1) Antenna port: Connect the antenna to the terminal
2) TEL 1: Connecting to Telephone
3) TEL 2: Connect to PSTN Line
4) On/Off switch: Turn On/Off the terminal
5) Power port: Make the flat side of power adapter plug be upturned and push it in
6) Data port: Connect the RS232 (9-pin) cable to the terminal for GPRS functions (Optional)
Power Indicator
Network Indicator
WT-1018 GSM Fixed Wireless Terminal___________________________________
5
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
Installing the SIM Card
Proceed as follows:
1. Slide back the SIM door and lift it up
2. Slide the SIM card into the SIM door making sure that the clipped corner of the SIM card lines up with
the clipped corner of the SIM holder
3. Close the SIM door
4. Slide the SIM door to lock the SIM card in place
Setting up the Terminal
Installation Condition
Require 220v AC power. GSM signal can cover the area where the terminal is placed. Signal quality affects
voice quality direct.
The installation for connecting to ordinary telephone direct
1. Install the SIM card proceeding as “Installing the SIM Card” on page 3.
2. Connect one end of the telephone line to “Telephone port” and the other ends connect to a telephone.
3. Connect PSTN Line to “Line Port”.
4. Install the antenna and power supply well. The distance between telephone and terminal is 1.5m at
least.
5. Connect one end of the power adapter to “Power port” and another end connects to 220v AC power.
About 10-45 seconds later, the terminal works in gear (The login time is different according to local
network).
When the terminal is ready to use, it will display as below
WT-1018
Draw your attentions: Because there are many types of ordinary telephone and their electric parameters
are different .In order to avoid mutual disturbance between telephone and terminal and affects voice quality
.The distance between telephone and terminal must be beyond 2m.
Signal Power
WT-1018 GSM Fixed Wireless Terminal___________________________________
6
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
The installation for connecting to register cost equipment
If users demand register cost during calls, register cost equipment can be connected between terminal and
ordinary telephone. Register cost equipment registers cost according to anti-polarity signal that is provided
by terminal.
Turn on and Turn off Wireless Terminal
Turn on: Connect the input end of power adapter to power socket and the output end to the port of
“DC6.5V” turn on terminal. About 15 – 45 seconds later (subject to local wireless network), the
terminal will logon successfully.
Turn off: Turn the switch to the OFF side and disconnect power adapter to turn off the terminal
Making Calls
1. Lift the handset or press “hand-free” key, you will hear dialing tone, then you can dial the telephone
numbers you want to call.
2. Dialing: dial the telephone numbers you want to call
3. On completion of dialed digits, you can press “#” to transmit telephone numbers. If you don't dial any
key for continual 6 seconds during the dialing, the terminal transmits the dialed telephone numbers
automatically.
4. If there is PSTN line input, the dialing numbers will automatically go through PSTN line. If the user
wants the dialed number to go through GSM then the user must press “*” before the destination
numbers.
5. If the user dial an International number start from “0” the dialing numbers will automatically go
through GSM.
6. When it is necessary to register cost, the terminal sends out anti-polarity signal (the signal is used to
register cost by register cost equipment). During a call, dial digital key or “*” or “#” to output DTMF.
7. If the calling party or called party hangs up, the terminal stops sending out anti-polarity signal.
8. If users dial barred numbers, telephone will give out the sound of three-time toot to ask the user to hang
up.
Answering Incoming Calls
When some calls are coming in, the telephone rings and the terminal will displays the incoming telephone
numbers on the screen. Now users can lift the handset or press “hand-free” to answer the call.
WT-1018 GSM Fixed Wireless Terminal___________________________________
7
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
Programming Code Setting (Have to enter Password before Start doing the Settings)
Steps:
1. Password Verification
Pick up phone, press **83211279#. If heard “du~~~” a continuous dialing tone, means the Password
enter correctly, and then will continue to go into programming setting mode. User is able to change the
settings now. If there is no continuous “du~~~”, means the Password enter not correct. And it will not
go into programming setting mode to change the settings. User can hook-on and pick up phone again to
enter the Password.
2. Programming Code
Refer to the Programming Table below. After enter the Programming Code, if you heard a busy tone
follow by the dialing tone, it means wrong programming code. If heard continuous “du~~~”, it means
the successful set up for that programming code. If just heard dialing tone, it means that the settings
area are full or enter wrong programming code.
During the setting for the programming code, user does not need to hook-on the Phone. When user
heard dialing tone after ONE setting means the user can continue the following setting.
3. To Quit from the Programming Code Setting
In Hook-on mode or Press “hand free” to quit from the setting.
No. Definition Program Code Description
1 Enter Password. Go
into Programming
Setting
**XXXXXXXX# After Password Verification, will enter
to the Programming Setting Mode.
(Initial Password for factory leaving is
sets up as “83211279”
2 Setting IP or
Gateway Number
*2*XXXXXXXXXXXX# After doing this setting, when making
calls, it will automatically dial Gateway
Number in front of the Destination
Number.
*2*# Delete the IP or Gateway Number
setting. All the calls are made will not
adding Gateway Number in front of the
Destination Number.
3 Restrict Incoming
Calls
*3*1*# Barred all Incoming Calls
*3*1*0# Cancel the setting for Barred Incoming
Calls
4 Restrict Local Calls
*3*2*# Barred all Local Calls
*3*2*0# Cancel the setting for Barred Local Calls
Restrict
International Calls
*3*3*# Barred all International Calls
*3*3*0# Cancel the setting for Barred
International Calls
5 Restrict National
Calls
*3*4*# Barred all National Calls
WT-1018 GSM Fixed Wireless Terminal___________________________________
8
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
*3*4*0# Cancel the setting for Barred National
Calls
6 Setting Local Area
Code
*1*XXXXXX# When dialing Local Prefix Number, it
will automatically add Local Area Code.
Able to set up to 6 digits for Local Area
Code.
*1*# Delete Add Local Area Code.
7 Setting for adding
“0” in front of
destination number
*3*5*# After doing this setting, when making
call for International mobile phone
number, it will automatically add 0 in
front of the dialed number.
*3*5*0# Cancel the setting for adding “0”
8 Setting Local Prefix
Number Gateway
*4*1*# After doing this setting, when making
Local Calls, it will automatically dial
Gateway Number in front of the
Destination Number.
*4*1*0# Cancel dialing Gateway Number in front
of the Local Number
9 Setting
International Prefix
Number Gateway
*4*2*# After doing this setting, when making
International Calls, it will automatically
dial Gateway Number in front of the
Destination Number
*4*2*0# Cancel dialing Gateway Number in front
of the International Number
10 Setting National
Prefix Number
Gateway
*4*3*# After doing this setting, when making
International Calls, it will automatically
dial Gateway Number in front of the
Destination Number.
*4*3*0# Cancel dialing Gateway Number in front
of the International Number
11 Setting for Locking
SIM Card
*5*1*# After doing this setting, the terminal will
lock the SIM card with a password.
Note: The terminal can only lock the
SIM card if the SIM card PIN number is
1234 (default) otherwise it will display
“PIN ERROR 02”. The locked SIM
card can only be recognized by the
terminal for unlocking.
*5*1*0# Cancel Locking SIM card. After doing
this settings, terminal will unlock the
SIM card and restore the PIN number of
the SIM card to 1234 (default).
12 Setting for Locking
Terminal
*5*2*# After doing this setting, the terminal can
only accept this particular SIM card.
Only be able to use other SIM after
unlocking the phone or deleting the SIM
Card ID
*5*2*0# Cancel Locking Terminal.
13 Setting for Changing
Password
*6*XXXXXXXX# Before doing this setting, user will need
to use the default password “83211279”
to go into Programming Setting Mode to
be able to use this programming code to
change the password.
WT-1018 GSM Fixed Wireless Terminal___________________________________
9
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
Technical Specification
1. Working condition
Environment temperature: 0 ~ +50ºC
Relative humidity: 10%~95%
Air pressure: 86~106kpa
Environment yawp: ≤60dB (A)
2. Working frequency: GSM900MHz/GSM1800MHz
3. Stability of frequency: better than 2.5PPM
4. Signal sensitivity: -103dBM
5. Transmit power: <2w
6. Power: 220v±15% AC
7. The max distance between terminal and telephone: 100M
WT-1018 GSM Fixed Wireless Terminal___________________________________
10
COPYRIGHT ©2007 WITURA CORPORATION SDN BHD
Troubleshooting
Phenomena Trouble Trouble Shooting
Signal indicator isn’t
lit
Failed in login onto
GSM network
1. The signal is too weak Please move the terminal to the
place where signal is stronger.
2. Check whether antenna is connected well.
3. SIM card is locked. Please contact the service provider.
Signal indicator
flashes fast Signal is too weak
1. Check whether antenna is connected well.
2. The signal is too weak Move the terminal or antenna to
the place where signal is strong.
Power indicator isn’t
lit
Having not connect
to power supply or
there is some trouble
with power adapter
1. Check whether the adapter is connected well.
2. There is some trouble with the power adapter
Please contact the provider of the terminal.
Only free numbers
can be called out
The residual money
on SIM card is too
less
Add money to the SIM card subscriber
Can’t hear sound
during calls
The malfunction on
the telephone Change the connected telephone with a good one
Poor voice quality
during calls or there
is echo during calls
The voice volume is
too high or the
signal of network is
too weak.
1. Adjust voice volume to be lower.
2. The local signal is too weak. Move the terminal to the
place where signal is stronger.
3. Make the antenna is longer from the telephone
4. The voice quality of the connected telephone isn’t good.
Change the connected telephone
5. Trouble on the GSM network.
No ringing sound The malfunction on
the telephone
1. Malfunction on the connected telephone
2. Malfunction on terminal. Please contact the provider of
the terminal.
Incoming calls can’t
be answered
The connected
telephone does not
match the terminal or
forbidding answering
incoming calls is set
1. Change the connected telephone with a suitable one.
2. Forbidding answer incoming calls is set up, please
contact the service provider.
We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all
requirements. All specifications are subject to change without notice. For more information, contact Witura Corporation.
Phone: +604-2289053 Fax: +604-2289146 Address: 18-8-C, Gurney Tower, Persiaran Gurney, 10250, Penang, Malaysia.
Table of contents
Other Witura Touch Terminal manuals
