Wodschow TEDDY User manual

1
A/S WODSCHOW & CO. Kirkebjerg Søpark 6
DK-2605 Brøndby
Denmark
Phone: [phone]
[e-mail]
www.bearvarimixer.com
GB
InstallatIon of new mIxer:
The following equipment is included:
√Cable √Hook
√Bowl √Beater
√Lid for the bowl √Whip
√Filling skid √Splash guard
Before taking the mixer into use, check that all parts are deliv-
ered.
Dimensions and weight
TEDDY incl. equipment:
• Netweightwithequipment: 22,0kg
• Outsidedimensionsofmixer: 462x240x400mm
Location:
The mixer is to be placed on a stable and horizontal table.
Guarantee:
The guarantee does not cover faults resulting from faulty op-
eration, overloading and lacking observance of directions of
maintenance.
In case of complaints, please contact your supplier.
In case you want further information, please state machine type
and serial number of the mixer.
A/S Wodschow & Co. reserves the right to change and improve
the products without notice.
safety:
The machine is a technical tool, and is intended solely for work-
ing purposes.
The constant noise level of the workplace of the operator is
lower then 70 dB (A).
The safety of the user is achieved by:
• Themixerwillonlystartwhentheupperpartislowered.
• The upper part can only be tilted up when the mixer is stopped.
• Protection from excess current, excess voltage and too
low voltage.
• Themixerisprovidedwithxedsafetyguard.
The machine must only be used by persons aged
14 and over.
The machine must be monitored while it is in
operation.
The mixer is designed for manufacture of prod-
ucts which do not during processing cause
reactions or emit substances which may be
detrimental to the user.
Putting your ngers in the bowl while the mixer
is running may cause injuries.
Contents:
Guarantee:
....................................................................................................................................................... 1
safety:
....................................................................................................................................................... 1
InstallatIon of new mIxer:
................................................................................................................................. 1
ConneCtIon to power:
....................................................................................................................................... 2
IntroduCtIon to the mIxer:
................................................................................................................................ 2
reCommended workInG speeds:
.......................................................................................................................... 2
operatIon of the mIxer:
.................................................................................................................................... 3
maxImum CapaCIty of the mIxer:
......................................................................................................................... 3
overload:
....................................................................................................................................................... 3
CleanInG and hyGIene:
....................................................................................................................................... 3
maIntenanCe:
.................................................................................................................................................... 4
lIst of errors and possIBle solutIons:
............................................................................................................. 4
mountInG of aCCessorIes:
................................................................................................................................. 4
reCommended speeds for attaChment drIve:
...................................................................................................... 4
oPERATING INSTRUCTIONS
TEDDYTM 5L Mixer
™TEDDY is a registered
trademark belonging to A/S
Wodschow & Co.
Translation of the original user
manual 042017 GB

2
K
reCommended workInG speeds:
• Position1-2: Lowspeed Kneading
• Position1-3: Mediumspeed Mixing
• Position1-5: Highspeed Whipping
IntroduCtIon to the mIxer:
TEDDY is a small professional mixer for kneading, mixing and whip-
ping in all environments where professional equipment is required.
Any operation of the mixer is made by means of the rotary but-
tons on the sides of the mixer. The two buttons can be used
simultaneously or individually and are used both for start/stop,
speed regulation and as opening/closing function.
The attachment drive Amakes it possible to connect meat
mincer.
ConneCtIon to power:
The enclosed cable must be used.
The mixer must be connected to earth!
• Onlysinglephasepowersupplywithearthmustbeused
for the mixer. Use the enclosed cable.
• Aplugwith2pins+earthmustbeused.
• Checkthatthevoltageofthepowersupplycorresponds
the voltage printed on the rating plate placed in the bottom
of the mixer and stated on the packing.
• The mixer must be protected by a differential circuit
breakerandafuseofmax.10A.
• A2.5ampfuseisbuiltintothecableconnector.
The power characteristics of the mixer:
Supply voltage Frequency Voltage Power consump.
(V) (Hz) (A) (W)
 230 50/60 1,6 500
 115 50/60 1,6 500
Equipment:
As standard the mixer comes with the following equipment:
• Bowlinstainlesssteel.
• White plastic lid for bowl
• Fillingskid.
• Doughhookinstainlesssteelforkneadingofdough.
• Beaterinstainlesssteelformixing.
• Whipinstainlesssteelforwhipping.
• Splashguardinplastic.
Extra equipment:
Hook Beater
Whip
Meat mincer
Bowl
Lid
Filling skid
Fig. 1 The construction of the mixer
Fig. 2 Recommended working speeds
Splash guard
A Attachment drive, extra equipment
B Housing of the planetary gear
C Safety guard stainless steel
D Bayonet shaft
E Lid
F Upper part
G Filling skid
H Control button (two pcs.)
I Base
J Bowl in stainless steel, contents 5 litres
K Locking arm

3GB
Product Raw
material
Approximate
max. quality
Bread dough, 60% kg dough 2,5
Flaky paste kg dough 2
Wipped cream l cream 1,5
Egg whites no. of eggs 20
Sponge cake no. of eggs 12
Meatballmix kg 3
operatIon of the mIxer:
The bowl must be mounted when the mixer
is started!
The machine must be monitored while it is
in operation
A. Turn the control button to the locking symbol (g. 3A).
B. Tilt backwards the upper part of the mixer.
C. Place a tool in the bayonet shaft and turn it counter-
clockwise to lock it in position (g. 4).
D. Place the bowl between the three locking bolts in the foot
of the mixer and turn it clockwise until locked (g. 5). Turn
the locking arm anticlockwise to hold the bowl.
E. Fill the ingredients in the bowl.
F. Tilt the upper part of the mixer, including tool, down.
G. Start the mixer by turning the control button away from
the locking symbol and past 1. To avoid splashing and
dustfromour,itisrecommendedtoincreasethespeed
gradually until the required speed is obtained (g. 3C),
(see g. 2 for recommended working speeds).
H. Stop the mixer by turning the control button back to neutral
position (g. 3B).
I. The upper part of the mixer can only be tilted backwards when
the control button is turned to the locking symbol (g. 3A) .
maxImum CapaCIty of the mIxer:
The working capacity of the mixer depends of:
• Thetoolused.
• Sortandquantityoftherawmaterials.
• Theoptimumspeedforagoodresult.
Too big quantities will always reduce the
quality of the product and the life of the mixer.
Overloading can also result in sudden stops.
overloadInG:
If the mixer is moving e.g. kneading dough, this is not due to
errors or overloading.
In case of overloading the electronic variator will reduce the
current to the motor and stop it.
In case of stop due to overloading, turn the
rotary button back to neutral position, and
the mixer can be started again.
If the motor stops after long time of operation, and cannot be
started immediately after, the thermosensor of the motor has
switched off the current, and the mixer needs to cool down before
it can be re-started. This protects the mixer from being destroyed.
The mixer contains two thermal cut-outs, which automatically re-
connect in case of previous disconnection by the thermosensor.
CleanInG and hyGIene:
The equipment’s ability to withstand the ingress of solid
objects and water/uids corresponds to IP42
After use:
• Removebowlandtools.
• Washthebowlandthetoolsinhotwateranddetergent/
degreaser/disinfectant.Rinsewithpurewateranddry.
Do not spray water on the mixer
Tools and bowl can be cleaned in dish-
washer.
• Wipethehousingoftheplanetarygear,thebayonetshaft
and the safety guard. Use a damp sponge and a detergent
/disinfectant.Rinsethepartswithspongeandpurewater.
• Check that the various parts have been cleaned thor-
oughly.
• Donotuseabrasivedetergents,whichcouldscratchthe
surface.
• Usecleaningagentssuitableforuseonpowderpainted
surfaces and plastic (polycarbonate).
3
A: Locking symbol B:Neutralposition C: Speeds
Fig. 4 Mounting of tool in the bayonet shaft.
Fig. 5 Place the bowl in the machine and twist it onto the
locking bolts and turn the locking arm anticlockwise.
Locking bolts
Fig.3 The three positions of the rotary button.
Close the ma-
chine by press-
ing down on the
top of the head
section.
You will hear a
click when the
machine has
closed properly

4
2
1
maIntenanCe:
The mixer requires no maintenance (motor and bearings for the
mechanical parts are greased for life).
Safety device:
Check the function of the safety device regularly:
• Themotormust stop when the rotary button is in neutral
position (see g. 3B).
If the safety device does not function, do
not use the mixer. Contact your dealer.
lIst of errors and possIBle solutIons:
If the problem cannot be solved, contact
your dealer.
The mixer does not start:
Check that ...
• Theupperpartofthemixerisinitsdownposition.
• Themixerispluggedinandconnectedtopower.
• Theelectricalpowersupplyiscorrect.
• Thefuseinthecableplug(g.6, 1) has not been burned.
If the fuse is defective, it can be replaced by the extra fuse
(g.6, 2) that is also available in the cable plug.
The mixer stops during work:
• The mixer is overloaded due to too high speed or too
heavy loading. See the paragraph “Overloading”.
In case of power failure set the rotary button
back to neutral position, and the mixer can
be started again.
The tool is stuck in the bayonet shaft:
Thisisnormallyduetoinsufcientcleaningordamagedhole
in the tool:
• Turnthetoolbackwardsandforwardsuntilitcanbere-
moved.
• Contactyourdistributor.
Unnormal noise:
Metallicnoise...
• Thetoolisdistortedandhitsthebowl.
• Thebowlhasbeendamagedorisnotinitsproperposi-
tion.
mountInG of aCCessorIes:
The mixer can be equipped with an attachment drive with variable
speed, and with the possibility of attaching the following equip-
ment:
• MeatmincerØ62mm,suppliedwithmeattray,stamper
andsetofknivesconsistingofbladeandplateØ8mm.
For further information regarding accesso-
ries, please see the special sheets following
the accessories.
The mixer must always be disconnected be-
fore mounting or dismantling of the accessory.
Mounting of accessories (g. 7):
• Assembletheaccessoryinquestion.
• Stopthemixer.
• TurnthecoverplateC away from the hole.
• Whenmountingthepre-mountedaccessoryA, the shaft
B is inserted into the attachment drive Dof the mixer.
• By turning the accessory until the pin Eis pointing to-
wards the slot Ga correct clutch is obtained.
• Theaccessoryispushedasfarintotheattachmentdrive
Das possible. (The pin Emust be in the slot G, then the
shaft of the accessory is in a correct clutch with the at-
tachment drive).
• TheaccessoryisfastenedbyturningthestarhandleH
clockwise.
Dismantling of accessories (g. 7):
• Stopthemixer.
• TurnthestarhandleHcounterclockwise until the locking
screw is free of the hole F.
• Takeouttheaccessoryoftheattachmentdrive,dismantle
and clean it.
Fig. 7 Mounting of accessories.
reCommended speeds for attaChment drIve:
Fig. 6 Fuses in the cable plug.