Wolf ICON PIR User manual

INSTRUCTION MANUAL
ENGLISH
www.wolnt.co.uk
WIDE TRANSMISSION
RANGE
RUMBLE
ALERT
HUBB
LINK
GLOBAL
MUTE
HIGH VISIBILITY
LEDS
LONG BATTERY
LIFE

FEATURES
The Wolf PIR alarm monitors your
fishing area with the help of a
built-in infrared sensor and gives a
direct signal on the device
if a stranger or an animal should
approach unnoticed day or night.
If something is approaching
your area a bright LED flashes.
There are 3 settings of sensitivity
available, Low, Medium and
High.
The PIR can also be paired
to the Wolf PIR remote
sounder or the Wolf Icon
HUBB or Qr receivers.
•
PIR Motion Sensor
Infrared Anti Theft
Alert System.
•
Infrared sensor alarm,
using the principle of
infrared light when there
are people or animals
passing the sensing area.
INSERTING BATTERIES
To insert batteries use screwdriver provided and open
the 2 screws on the battery compartment. When
inserting 3 new AAA batteries always replace all of
them. When PIR is not going to be used for a while it is
recommended to remove batteries in case of leakage.
BALL HEAD & MAGNET
Included with the ICON PIR Sounder
is a magnet for attachment to rear of
PIR Sounder.
The multi-angle ball head is for
attachment to a bankstick to enable
the ICON PIR Sounder to be used in
different positions.
POWER
BUTTON
Release to begin the start-up sequence.
POWER ON
When the PIR is turned off, Press for 4 seconds.
Good battery
level
OK battery
level
Bad battery
level

From any on state, press and hold
for 4 seconds.
Release to power off.
LED turns blue after 4 seconds.
POWER OFF
When the receiver is ready for
pairing, press and hold the button
for 8 seconds. The LED will pulse
blue to indicate the PIR is ready
for pairing.
Release to initiate pairing.
PAIRING
After power on the PIR will start an
arming sequence, with a flashing of
the LED in the selected alert colour.
The flashing gets faster as
the sequence completes.
This gives the user roughly 15 seconds to set up the
device and move out of the detection zone without
triggering an alert.After the sequence has completed,
the PIR will start detection.
ARMING SEQUENCE
Single presses of will allow the alert colour to be
changed. The current alert colour will be previewed
on the LED.
Further single presses of will cycle through available
colours, and a stealth mode with no LED indication.
ALERT COLOUR
A double press of button will cycle through the
sensitivity settings. Each setting is represented by a
different LED flash sequence as described below.
SENSITIVITY
SETTING LED SEQUENCE
Low Sensitivity 1 x Green Flash
Medium Sensitivity 2 x Green Flash
High Sensitivity 3 x Green Flash

WOLF
Suite 1, 284 Warley Hill, Great Warley,
Brentwood, Essex CM13 3AB
E: [email protected]
T: [phone]
E: [email protected]
www.wolfint.co.uk
For language translations of all
instructions and functions and care of
your Wolf PIR visit
www.wolfint.co.uk/product-manuals/
Information of troubleshooting is available at
www.wolfint.co.uk
Warranty
If you need information to the warranty please visit
www.wolfint.co.uk/product-warranty/
Please ensure to register your new Wolf product at
www.wolfint.co.uk/product-registration/
Customer Support
If you need support you can contact us by:
Telephone: [phone]
Email: [email protected]
More information can be found at
www.wolfint.co.uk/customer-support/
Languages available:
English / Italian / French / Dutch / German
E&OE
Product Code: WFIC026
Patents Pending:
GB 1721169.9 IGB 1721166.5 IGB 1721158.2
EP 18213109.4 IEP 18213012.0 IEP 18213022.9
Compliant to:
Safety EN 62368-1 IRED 2014/53/EU IRoHS
www.wolnt.co.uk