Wolf ICON Vi User manual

INSTRUCTION
MANUAL
LANGUAGE: ENGLISH
PIEZO
SPEAKER
HUBB/QR
HUBB LINK
BATTERY LEVEL
INDICATION
HIGH VISIBILITY
LED
WIDE TRANSMISSION
RANGE
WATER
RESISTANT ELECTRONICS
LOW POWER
SAVING MODE
VIBRATION
DETECTION

CONTENTS
FEATURES 3
INSERTING BATTERIES 4
ALARM CARE 4
POWER ON 4
MODE BUTTON 4
RUBBER SOCKET HOLDERS 4
STAINLESS STEEL STUD WITH
LOCKING NUT & COMPRESSION WASHER 4
CONTROL KNOBS 5
VOLUME/TONE SETTINGS 5
VIBRATION DETECTION 5
PAIRING 5
MUTE BUTTON 5
FACTORY DEFAULT 5
FORWARD DETECTION 5
BACKWARD DETECTION 5
ALERTS 6
SMART LED PORT 6
CONFIGURATION MENU 6
ADJUSTMENT OF ViALARM
CONTROLS FROM HUBB 7
DEVICE MENU 7
LED ILLUMINATION COLOURS 7
BITE LED BRIGHTNESS 7
ADVANCED MENU 7
ALERT TIMEOUT 7
ALERT VOLUME 8
ALERT TONE 8
DEVICE STATUS 8
BATTERY LEVEL INDICATION 8
RANGE TEST 8
ANTI-THEFT 8
MUTE 8
ADJUSTMENT OF ViALARM
CONTROLS FROM QR 8
MOISTURE OUTLET
SMART LED PORT
ISOTOPE SLOTS
VOLUME/TONE DIAL
MODE BUTTON
LED
NON-SLIP RUBBER GRIP
AND ROD PROTECTOR
NON-SLIP RUBBER GRIP
AND ROD PROTECTOR
SENSITIVITY DIAL
PIEZO SPEAKER
PAIR/MUTE BUTTON
STAINLESS LOCKING NUT
STAINLESS STUD
COMPRESSION WASHER

3
FEATURES
• Dropback Differentiation
• High Visibility Dual Bite LED - 7 Changeable Colours -
Green, Blue, Cyan, Yellow, Magenta, White or Red
• LED Indicates Forward and Backward - Flashes on
dropback
• LED Time adjustable via HUBB and Stealth mode
(LED Off)
• Piezo Speaker
• Indicator Port - Smart LED Drive, colour change on bite
detection
• HUBB/Qr HUBB Link - Receives and Transmits Commands
• Pairing Button
• Menu Button
• Extreme Transmit/Receive Range 2km
• Water Resistant Electronics
• Battery Level Indication
• Indication type - Event sent to HUBB
• Mute - 60/30 Seconds Selectable
• On/Off
• Hard Case
• Non-Slip Rubber Grip & Rod Protectors
• Stainless Steel Stud, Locking Nut & Compression Washer
• Battery Life - 700hrs on Standby
• Betalight Slots x 2 - Size 6mm x 2mm
• Rubber Socket Cover
• Range Test
• Power Down Alert To HUBB - Anti Theft
• LED Brightness - The brightness of the LED can be
adjusted for different fishing situations
• Volume Settings - Adjustable from Alarm & HUBB
• Tone Settings - Adjustable from Alarm & HUBB
• Sensitivity Settings - Adjustable from Alarm
• Tone difference - Run Forward & Dropback
• Latching Run Time - 30 Seconds Adjustable via HUBB
• Low power mode is available when not paired to HUBB
only. After HUBB pairing LP mode can be re-enabled by a
hard reset of the Bite Alarm
• Warranty 3 Years with 4th Year Free
Register you ICON at www.wolfint.co.uk

4
MODE BUTTON
A single press of the Mode button (top side button). Toggle
between volume or tone adjustment. The colour of the LED
indicates the battery level: Green - Good Battery Level
- Yellow - OK Battery Level Red - Low Battery Level, for
approximately 8 seconds. After 30 seconds to control will
revert back to volume.
To insert batteries use a Philips screwdriver and open 2 screws
on battery compartment. When inserting new batteries always
replace all of them and turn off Alarm before replacing.
ALARM CARE
After use of Alarm in damp conditions, dry off alarm exterior
and leave to dry out somewhere warm and dry before
packing away and if not going to be used for a while it is
recommended to remove batteries in case of leakage.
To power up the Vi Alarm.
Press Mode button for 3 seconds for
On/Off then release. When switched
Off a tone will sound. After 0.5
seconds LED lights dim blue and gets
brighter until after 3 seconds blinks to
indicate that the alarm has turned on.
The user can then let go. After turn On
the LED will light with battery level.
INSERTING BATTERIES
POWER ON
Good battery level OK battery level Low battery level
RUBBER SOCKET HOLDER
When Port is not being used the
rubber socket holder should be
pressed into port. When not needed
it should be pressed into the socket
holder on reverse of Vi Alarm.
3 AA 1.5v
Batteries
Battery
Cover
STAINLESS STEEL STUD WITH LOCKING
NUT & COMPRESSION WASHER
Incorporates a 3/8” stainless steel stud
with locking nut and compression
washer for attaching the alarm to
your buzz bar or bankstick. Be careful
when attaching the Vi Alarm to
banksticks, buzz bars etc. and avoid
over-tightening.

5
FACTORY DEFAULT
To reset the Vi Alarm to factory settings, and remove all user
data, hold the button while powering on the Vi Alarm.
After the white LED illuminates, release the button. A tone
will play to confirm the reset.
FORWARD DETECTION
Forward line movement is indicated with a single tone set
by the user with the Tone dial. For each detection the main
indicator LED will illuminate. A new detection whilst the LED
are illuminated will cause the LED to blink Off once for each
detection. Once detections have stopped the LED will remain
illuminated for 30 seconds default. Adjustable from HUBB.
BACKWARD DETECTION
Backward line movement is indicated with alternating tones
set by the user with the Tone dial. Single alternating tones will
be played indicating each detection. For each detection the
main indicator LED will illuminate A new detection whilst the LED
are illuminated will cause the LED to blink Off once for each
detection. Once detections have stopped the LED will remain
illuminated for 30 seconds default. Adjustable from HUBB.
PAIRING
When the receiver device is ready for pairing with HUBB
(see receiver device instructions), press and hold the
button until indicator LED turns Blue then release Button,
this will initiate pairing.
MUTE BUTTON
When not in configuration menu, single presses on the Mute
button (Bottom side right) will put the alarm in to mute. In this
state the main LED will go white, alerts will still be indicated
by the set indicator colour but no sound will be produced.
After a set time the local mute will expire and the device will
return to normal. A single press will give a 30 second local
mute. A single press whilst muted will cancel the mute.
CONTROL KNOBS
The Vi Alarm control knobs can be used to adjust various
settings.
VOLUME/TONE SETTINGS
The V/T Dial (Top Right) adjusts the volume of
the alerts on the Vi Alarm and (after pressing
the mode button) adjusts the pitch of the
alerts on the Vi Alarm.
VIBRATION DETECTION
The S Dial (Bottom Right) has 15 Sensitivity
Settings on the Vi alarm.

6
ALERTS
ALERT TYPE LED INDICATION SOUND
Forward
Solid Alert Colour
Single Tone at user
selected pitch.
Dropback
Flashing Alert Colour
Tone at alternating
pitch.
Vibrate
Solid Alert Colour
Dual Tone at user
selected pitch.
Battery
Critical
Flashing Red
No tone played.
CONFIGURATION MENU
Holding down the Mode button will cause the LED to flash
Yellow - Blue - Yellow. Releasing the Mode button, a tone is
played indicating the device is in configuration menu.
Whilst in the configuration menu the Volume dial can be
adjusted to change the indicator LED colour: Off, Red,
Green, Blue, Cyan, Yellow, Magenta and White.
Whilst in the configuration menu the Sensitivity dial can be
adjusted to change the brightness of the LED.
Whilst in the configuration menu a press of the Mute button
cycles between the three vibration detection modes.
One magenta flash and a single bleep enters vibration
with no direction mode. This will indicate a vibration in any
direction with an alert tone and a momentary blue flash
followed by the selected alert colour on the indicator LED.
Two Magenta flashes and two bleeps enters vibration mode
with hybrid detection. In this mode the alert will indicate
direction when this can be accurately determined. If there is
insufficient direction information, then a vibration indication
alone will be triggered with an alert tone and the selected
alert colour on the indicator LED.
Three magenta flashes and three bleeps enters vibration
mode with forwards and backwards detection. This will
indicate a vibration in any direction with an alert tone and a
momentary blue flash followed by the selected alert colour
on the indicator LED. (When used on the most sensitive range
forwards/ backwards detection may give false direction
information). To exit the configuration menu press the Mode
button. A tone is played unless the volume is set to OFF.
LED ILLUMINATION BRIGHTNESS
While in the configuration menu the vibration sensitivity dial
adjusts the brightness of the LED.
SMART LED PORT
Smart LED Drive. Colour matching LED and 2 options,
*when used with WOLF Indicators only. Also drives some
3rd party indicators.

7
ADJUSTMENT OF Vi ALARM
CONTROLS FROM HUBB
DEVICE MENU
When the HUBB has been paired with the Vi press the
corresponding Alarm channel to change any settings.
Press and hold channel button until ‘Device Menu’ is shown
on screen.
On activation of the bite Alarm
the tone is replicated on the HUBB
and the HUBB LED’s replicate the
alert colour shown on the bite
Alarm. Depending on the HUBB/
Qr settings, the HUBB/Qr will also
vibrate on alert.
When ‘Device Menu’ is shown, use OK button to enter sub
menu.
Go to ‘Sensitivity’ to adjust the connected bite Alarm line
sensitivity. When confirming this option a message will be sent
to the bite Alarm, if successful you will be notified on screen.
< Device Menu >
[Enter]
LED ILLUMINATION COLOURS
7 Colours: Blue - Cyan - Yellow -
Magenta - White - Green - Red -
Stealth Mode (Off)
Go to ‘Alert Colour’ to change
the colour used to display alerts
on the Vi Alarm and HUBB.
< Alert Colour >
Blue
BITE LED BRIGHTNESS
Go to ‘LED Brightness’ to change
the brightness of the LED
displayed on the Vi Alarm.
< LED Brightness>
73%
ADVANCED MENU
Use the back button to
leave ‘Device Menu’ and go
‘Advanced Menu’ and use OK
button to enter this menu.
< Advanced Menu >
[Enter]
ALERT TIMEOUT
Go to ‘Alert Timeout’ to adjust
the time that the LED remains
turned on after an alert on the
Vi Alarm.
60 seconds / 30 seconds / 20
seconds / 10 seconds /
5 seconds
< Alert Timeout >
30 secs

8
ALERT VOLUME
In ‘Advanced Menu’ go ‘Alert
Volume’ to adjust the volume of
the Vi Alarm alert.
< Volume >
50%
ALERT TONE
In ‘Advanced Menu’ go ‘Alert
Tone’ to adjust the pitch on the
Vi Alarm and the HUBB.
< Alert Tone >
28%
DEVICE STATUS
Use the back button to leave ‘Advanced Menu’ and
navigate to the option titled ‘Device Status’ and enter sub
menu using OK button.
ANTI-THEFT
When turning off the connected Alarm, a tone is played
on the Vi Alarm and HUBB for theft prevention.
BATTERY LEVEL INDICATION
Navigate to the option
‘Battery Level’.
This provides a detailed
measurement of the Alarms
battery level.
RANGE TEST
Navigate to the option ‘Range
Test’ and use the OK button
to begin the test. When a
connection is established the
HUBB will report the signal
strength of the connected Vi
Alarm and also indicates that
the LED is working.
< Battery Level >
97%
< Range Test >
[Start]
MUTE
When the Vi Alarm is paired with the ICON Qr some settings
are not available. See Qr instructions for information on
pairing with the Vi Alarm.
Sensitivity Settings not available on Qr or Hubb.
Brightness adjustment not available on Qr.
Volume Settings not available on Qr.
Tone Settings not available on Qr.
Latching Run time setting not available on Qr.
Pressing the Mute button once should mute all connected
Alarms. On activation neither the HUBB or Alarm will play a
tone. A double press of the Mute button will undo the mute
on the HUBB and Alarms.
ADJUSTMENT OF Vi ALARM
CONTROLS FROM Qr

WOLF INTERNATIONAL
Suite 1, 284 Warley Hill, Great Warley,
Brentwood, Essex CM13 3AB
E: [email protected]
T: [phone]
E: [email protected]
www.wolfint.co.uk
For language translations of all instructions
and functions and care of your Wolf
International ICON Alarm or HUBB visit
www.wolfint.co.uk/product-manuals/
Information of troubleshooting is available at
www.wolfint.co.uk
Warranty
If you need information to the warranty please visit
www.wolfint.co.uk/product-warranty/
Please ensure to register your new Wolf product at
www.wolfint.co.uk/product-registration/
Customer Support
If you need support you can contact us by:
Telephone: [phone]
Email: [email protected]
More information can be found at
www.wolfint.co.uk/customer-support/ Languages available:
English / Italian / French / Dutch / German
E&OE
Product Code: WFIC023
Patents Pending:
GB 1721169.9 IGB 1721166.5 IGB 1721158.2
EP 18213109.4 IEP 18213012.0 IEP 18213022.9
Compliant to:
Safety EN 62368-1 IRED 2014/53/EU IRoHS
www.wolnt.co.uk