Woodland 02GRFF4118-V1 User manual

02GRFF4118-V1
Overall Dimensions:
Length = 4246mm
Width = 1512mm
Height = 3459mm
Base Dimensions:
Length = 2504mm
Width = 1525mm
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
02GRFF4118-V1
For Assistance Please
Contact Customer Care on
01636 880514
2mm Drill bit
x2
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
This building should be erected by
two adults
For ease of assembly, you must pilot
drill all screw holes and ensure all
screw heads are countersunk.
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces
of the timber. You are strongly advised
to wear gloves when working with or
handling rough sawn timer.
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not
supplied) including a Phillips screwdriver, Stanley knife, wood saw, step
ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
-Not suitable for children under 36 months.
-Please retain product label and instructions for future reference.
-This product has been designed to be permanently xed into the ground and
not present a hazard.
-Ensure the base is level and is built on rm ground, to prevent distortion. -We
recommend that this product is situated at least two meters away from any
structure or obstruction, including but not limited to, fencing, garages,
houses, overhanging branches, laundry lines or electrical wires.
-We highly recommend that this product is not installed on a hard surface
such as concrete, or asphalt.
-To ensure the longevity regarding the colour of any plastic objects attached
to this product we suggest, such items are positioned away from constant
direct sunlight.
-Any modications that are made to this product i.e. Adding another unit
should be carried out according to the manufactures instructions.
-This product is delivered pressure treated with a water based treated.
Maintenance
Maintenance should be carried out at regular intervals. If checks are not carried out the product could overturn or otherwise
become a hazard. Check at the beginning of each season and at regular intervals. Access all the nuts, bolts and screws for
tightness, tighten when required. Check all coverings for bolts and sharp edges, replace any defective parts in accordance with
the manufacturer’s instructions.
Sun
To ensure the longevity regarding the colour of any plastic objects attached to this product we suggest, such items are
positioned away from constant direct sunlight.
WARNING: Only for domestic use
Not suitable for children under 36 month
To be used under direct supervision of an adult
This product has been tested to BS EN 71 standard however, we cannot accept responsibility
for your safety whilst erecting or using this product if these instructions have not been
followed.
Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN
www.merciagardenproducts.co.uk
The Woodland Trust is a charity
register in England and Wales (No.
294344) and in Scotland (No.
SCO38885).
Small Skirting - 1320mm x 27mm x 144mm QTY 2
Fixing Kit
Big Base QTY 1
Long Post - 2750mm x 75mmx 75mm QTY 2
2
1
Roof
QTY 2
4567
8
9
10
Short Post - 840mm x 75mmx 75mm QTY 1
Long Skirting - 1673mm x 27mm x 144mm QTY 2
14
12
11
Medium Skirting - 1525mm x 27mm x 144mm QTY 1
3
Short Rail
QTY 2
Medium Rail QTY 2
Long Rail QTY 1
MediumPost - 2450mm x 75mmx 75mm QTY 4
Small Base QTY 1
Step QTY 1
Back Post - 1000mm x 75mmx 75mm QTY 2
13

100mm Screw x 22
Roof Fascia - 1077mm x 27mm x 70mm QTY 4
Over Bar - 1321mm x 27mm x 70mm QTY 1
Ladder Leg - 1690mm x 70mm x 32mm QTY 2
15
17
16
Slide
Ladder Step
QTY 4
Roof Triangle
QTY 2
Roof Support QTY 4
Handle
QTY 4
Ground
Stake
QTY 4
Under Support - 610mm x 27mm x 70mm QTY 1
21
18
19
23
24
22
20
Slide Support 27x70x500mm QTY 1
25
Nail Bag &
Ironmongery
50mm Screw x 31
80mm Coach Screws x 58
Bolted Connections x 51
60mm Screw x 50
30mm Screw x 6
Corner Brace - 375mm x 44mm x 58mm QTY 12
Roof Trim 1633mm x 30mm x 12mm QTY 1
27
Roof Trim 1633mm x 45mm x 12mm QTY 1
28
26
Bolted Connection
When attaching the
bolt and the
connection, ensure
that the connection
itself sits flush with
the face of the
timber that you
have fixed it to.This
is shown in the
diagram to the left.
Timber
Connection
Bolt

Erect the play equiptment on a
firm and level base, ensure
base has suitable drainage
free from areas where
standing water can collect.
(See front page on base
requirements).
Step 1
6 x 80 mm Coach Screws
4 x Bolted Connections
Place 2 Medium Posts flat on the
ground, parallel to each other.
Attach the Small Skirting to the
ends flush with the bottom and
sides of the Posts using 4 Bolted
Connections per Skirting board.
Attach the Step between the Posts
1425mm from the bottom of the
Posts using 6 x 80 Coach Screws.
1425
700
1171
3
12
12
8
11
8
11
WHEN FIXING BOLTED CONNECTIONS
ENSURE THE END FITS FLUSH WITH
THE CLADDING
We strongly recommend pre drilling
holes before xing screws.
Place the base centrally
against the Medium posts, as
shown in the diagram. The
Big Base should be fixed with
27mm overhang either side
of the post and 1430mm
from the bottom of the posts
to the top of the base.
Fix the Big Base to the Posts
from the outside of the Posts
into the Base using a bolted
connection and a 100mm
screw.
Step 2
2 x Bolted Connections
1
2 x 100mm Screw
We strongly recommend pre drilling
holes before xing screws.
With some help, turn the
assembly on its side and attach
the Long Posts and short
skirting, 27mm from each base
end.
Fix the long skirting usng
bolted connections and fix
each post using a bolted
connection and a 100mm
screw.
Step 3
6 x Bolted Connections
2 x 100mm Screw
We strongly recommend pre
drilling holes before xing
screws.
Attach the Medium Rails to the
assembly as shown in the
diagram.
Step 4
16 x Coach Screws
5
5
We strongly recommend pre drilling
holes before xing screws.

Assemble the Ladder, so the
Ladder Steps are the same
distance apart as shown in the
diagram.The Ladder Legs should
be pushed right up to the grooves
in the Ladder steps, so the ladder
doesn’t rock.
Step 5
8 x 80mm Coach Screws
274mm
327mm
327mm
327mm
307mm
15
22
15
22
22
22
We strongly recommend pre drilling
holes before xing screws.
Step 6
1 x 80mm Coach Screw
Stand the main assembly up
and attach the Ladder to the
inside of one of the Posts, the
Ladder end should be flush
with the Base.
We strongly recommend pre drilling
holes before xing screws.
Don’t climb the ladder yet as
the assembly isn’t secure.With
the aid of a step ladder attach
an Over Bar to the inside of the
Posts, adjacent to the top of the
Rails. Fix using a bolted
connection and a 100mm
screw into each post.
Attach the Short Post to the
other side of the ladder using
a coach screw and a bolted
connection and a 100mm
screw into the Base and Over
Bar.
Attach the Under Support
between the posts flush with
the top of the base. using
50mm screws
Step 7
18
4 x Bolted Connections
1 x Coach Screw
14
17
9
2
4 x 100mm Screw
3 x 50mm Screw
We strongly recommend pre drilling
holes before xing screws.
Step 8
8 x 80 mm Coach Screws
4 x Bolted Connections
Place 2 short posts flat on the
ground, parallel to each other and
1375mm apart. Attach the Long
Skirting to the ends flush with the
bottom and sides of the Posts
using 4 Bolted Connections per
Skirting board. Attach the long
rail to the posts as shown in the
diagram, flush to the top of the
Posts, using 8 Coach Screws per
Rail.
12
12
We strongly recommend pre drilling
holes before xing screws.

Flip the assembly over and
place the Small base
between the Posts as show
in the diagram.The Base
should be fitted 27mm
outside of the posts. Fix the
Base to the Posts from the
outside of the Posts into the
Base using a bolted connec-
tion and a 100mm screw for
each post.
Step 9
2 x Bolted Connections
2
2 x 100mm Screw
We strongly recommend pre drilling
holes before xing screws.
Don’t climb the ladder yet as
the assembly won’t be
secure.
Push the assembly in step 9
up against the assembly in
step 7. Once central to the
opposing base, secure
through the framing on the
underside of the small base
into the step .
Step 10
3 x Bolted Connections
We strongly recommend pre drilling
holes before xing screws.
6
6
12 x Bolted Connections
16 x Coach Screws
Attach the two Long Skirt-
ings to the edges of the
posts as shown in the
diagram using bolted
connections.
Attach the Short Rails as
shown in the diagram using
Coach Screws.
Step 11
10
10
We strongly recommend pre drilling
holes before xing screws.
12 x 100mm screws
Attach the two Roof Posts in
both back corners fix in
place through the rails with
100mm screws.
Step 12 13 13
We strongly recommend pre drilling
holes before xing screws.

16
20
16
16
16
20
Attach the Roof Fascias and the
Roof Triangles as shown in the
diagram.
8 x 50mm Screws
We strongly recommend pre drilling
holes before xing screws.
Step 13
8 x 30mm Handle Bolts
2 x 60mm Screws
Attach the slide support centrally
10cm from the the edge of the
base and fix using 60mm screws
Attach a handle to the inside of
each post at the ladder side,The
bottom of the handles should be
320mm above the base.
Attach a handle to the inside of the
uprights at the slide side (handle
supports) the bottom fixing should
be 100mm above the base.
We strongly recommend pre drilling
holes before xing screws.
Step 14
Step 15
Step 16
Attach both Roof panels to the
assembly in the previous step
as shown.
12 x 50mm Screws
7
7
We strongly recommend pre drilling
holes before xing screws.
Place the Slide centrally
between the Posts and bolt it
into position into the Base.
Ensure the slide is pushed
against the base so there is no
gap, before fixing screws.
2 x 80mm Coach Screws
23
We strongly recommend pre drilling
holes before xing screws.
21 21 21
25
21

Step 17
Attach the Roof Supports to
the roof assembly as shown in
the diagram, 95mm away from
the end of the Roof panel
framing.
8 x 50mm Screws
95
95
95
95
19
19
19
19
We strongly recommend pre drilling
holes before xing screws.
Step 18
With Some help place the Roof
into position on top of the main
assembly, with the front and
back posts resting on the Roof
Supports. Bolt the Roof in place
from the Fascias into the Posts.
4 x Bolted Connections
We strongly recommend pre drilling
holes before xing screws.
Dig holes 400mm into the
ground, where the Ground
Anchors will be positioned.
Place the anchor into the
ground and bolt to the inside of
of the four outer Posts. Fill the
ground back in making sure the
ground is compact.
Step 19
4 Ground Anchor Bolts
24
24
24
24
We strongly recommend pre drilling
holes before xing screws.

We strongly recommend pre drilling
holes before xing screws.
Step 20
Fix two corner braces to each
post using 60mm screws.
Secure through the brace into
the post and through the
skirting into the brace.
48` x 60mm Screws
26
After completing assembly,
using a sanding
block/suitable mechanical
sander, sand off any sharp
corners or rough areas of
timber.
We strongly recommend pre drilling
holes before xing screws.
Step 21
Fix the two roof trims to the top
of the roofs creating a ‘V’ shape
to cap the roof and fix in place
with 30mm screws.
6 x 30mm Screws
27
28