woodmizer STRB-S Guide

Super Surge Brake Trailer
Safety, Operation, Maintenance
& Parts Manual
STRB-S Trailer Option
Safety is our #1 concern! Read and understand
all safety information and instructions before oper-
ating, setting up or maintaining this machine.
September 2008
Form #795

ii SBS97doc091818 Table of Contents
Table of Contents Section-Page
SECTION 1 SURGE BRAKE HITCH 1-1
1.1 Operation ................................................................................................1-1
1.2 Maintenance ...........................................................................................2-1
SECTION 2 PARTS LISTS 3-1
2.1 Trailer Hitch Assembly, Surge Brake ....................................................3-1
2.2 Trailer Axle Assembly, Surge Brake......................................................3-3
LT30 Super Rev. H4.00+
LT40 Super Rev. H5.00+
LT30HD Rev. H8.00+
LT40HD Rev. H8.00+
LT30HD Super Rev. H8.00+
LT40HD Super Rev. H8.00+
LT50HD Rev. A1.00+
2.3 Trailer Axle Assembly, Surge Brake......................................................3-5
LT30HD Rev. G1.00 - H7.00
LT40HD Rev. G1.00 - H7.00
LT30HD Super Rev. G1.00 - H7.00
LT40HD Super Rev. G1.00 - H7.00
2.4 Outriggers...............................................................................................3-7
LT70HD Rev. A1.00+
2.5 Outrigger Assembly, Long .....................................................................3-8
LT30HD Rev. H6.00+
LT40HD Rev. H6.00+
LT30HD Super Rev. H6.00+
LT40HD Super Rev. H6.00+
LT50HD Rev. A1.00+
LT70HD Rev. A1.00+
2.6 Outrigger Assembly, Long ...................................................................3-10
LT30HD Rev. G9.00 - H5.00
LT40HD Rev. G9.00 - H5.00
LT30HD Super Rev. H1.00 - H5.00
LT40HD Super Rev. H1.00 - H5.00
2.7 Outrigger Assembly, Long ...................................................................3-12
LT30HD Rev. G1.00 - G8.00
LT40HD Rev. G1.00 - G8.00
LT30HD Super Rev. G1.00 - G9.00
LT40HD Super Rev. G1.00 - G9.00
2.8 Outrigger Assembly, Front...................................................................3-14
LT40HD Rev. G9.00+
LT40HD Super Rev. H1.00+
LT50HD Rev. A1.00+
LT70HD Rev. A1.00+
2.9 Outrigger Assembly, Front...................................................................3-16
LT40HD Rev. G1.00 - G8.00
LT40HD Super Rev. G1.00 - G9.00
TOC

Table of Contents Section-Page
Table of Contents SBS97doc091818 iii
2.10 Outrigger Assembly, Long (LT30HD Super) ......................................3-18
LT30HD Super Rev. H6.00+
2.11 Outrigger Assembly, Short Front .........................................................3-20
LT30HD Rev. G9.00+
LT40HD Rev. G9.00+
LT30HD Super Rev. H1.00+
LT40HD Super Rev. H1.00+
LT50HD Rev. A1.00+
LT70HD Rev. A1.00+
2.12 Outrigger Assembly, Short Front .........................................................3-22
LT30HD Rev. G1.00 - G8.00
LT40HD Rev. G1.00 - G8.00
LT30HD Super Rev. G1.00 - G9.00
LT40HD Super Rev. G1.00 - G9.00
2.13 Outrigger Assembly, Rear....................................................................3-24
LT40HD Rev. G9.00+
LT40HD Super Rev. H1.00+
LT50HD Rev. A1.00+
LT70HD Rev. A1.00+
2.14 Outrigger Assembly, Rear....................................................................3-26
LT40HD Rev. G1.00 - G8.00
LT40HD Super Rev. G1.00 - G9.00
2.15 Outrigger Assembly, Short Rear ..........................................................3-28
LT30HD Rev. G9.00+
LT40HD Rev. G9.00+
LT30HD Super Rev. H1.00+
LT40HD Super Rev. H1.00+
LT50HD Rev. A1.00+
LT70HD Rev. A1.00+
2.16 Outrigger Assembly, Short Rear ..........................................................3-30
LT30HD Rev. G1.00 - G8.00
LT40HD Rev. G1.00 - G8.00
LT30HD Super Rev. G1.00 - G9.00
LT40HD Super Rev. G1.00 - G9.00
2.17 Trailer Lights........................................................................................3-32
LT30HD Rev. K2.00+
LT40HD Rev. K4.00+
LT40HD Super Rev. K2.00+
LT50HD Rev. A3.00+
LT70HD Rev. B1.00+
LT70HD Super Rev. A1.00+
2.18 Trailer Lights........................................................................................3-34
LT30HD Rev. G1.00 - K1.03
LT40HD Rev. G1.00 - K3.01
LT30HD Super Rev. G1.00+
LT40HD Super Rev. G1.00 - K1.02

iv SBS97doc091818 Table of Contents
Table of Contents Section-Page
LT50HD Rev. A1.00 - A2.02
LT70HD Rev. A1.00 - A9.00
INDEX 1-I

Surge Brake Hitch
Operation
Surge Brake Hitch SBS97doc091818 1-1
1
SECTION 1 SURGE BRAKE HITCH
1.1 Operation
IMPORTANT! Your vehicle should be equipped with a
Class 34 hitch with a solid 2” ball (not two-piece) and rated
for at least 5000 pounds (2270 kg). The hitch should be
correctly mounted to the towing vehicle so that it will be
able to pull this type of load.
1. Pull the mill behind the towing vehicle and place the hitch over the ball coupling on your
vehicle. Adjust the coupler if necessary so it is as tight as possible on the ball and the
locking lever can still be opened and closed.
See Figure 1-1.
2. Flip the locking handle upward, being sure the bracket underneath firmly clamps around
the ball. Secure the locking handle with the safety pin.
DANGER! Make sure hitch bracket is securely fastened
around ball before towing the sawmill. Ball should be com-
pletely engaged by the hitch bracket and securely locked in
FIG. 1-1

Surge Brake Hitch
Operation
1
1-2 SBS97doc091818 Surge Brake Hitch
place. Use the hitch only with the specified ball size. Fail-
ure to do so may result in serious personal injury and/or
severe machine damage.
3. Cross the safety chains underneath the hitch and hook to the vehicle. The chains should
be connected so that there is still slack in the chains when the vehicle is turned sharply in
either direction.
DANGER! Make sure your hitch has adequate safety chain
hookups. Do not use eyebolts for safety chain hook-up.
Safety chains should be hooked to bumper of vehicle so
that each chain would pull the trailer equally in the event the
hitch became disengaged. Failure to do so may result in
serious personal injury and/or severe machine damage.
4. Connect the surge brake activator cable to the vehicle. This cable should be connected in
case the hitch becomes unhooked and the safety chains fail. The surge brake activator
cable would then activate the braking mechanism. There should be enough slack in the
brake cable that the brake won't engage until the safety chains are stretched tight.
5. Connect the light wiring harness plug from the sawmill to the recetacle on your vehicle.
Check signals and brake lights.
6. Raise the front outrigger. Recheck that all loose items are removed or secured (such as
Resaw Option, Shingle/Lapsiding Option, cant hooks, etc.).
7. The hitch on the mill is adjustable. It should be raised or lowered to let the mill travel hori-
zontal to ground level. Adjust by removing the two mounting bolts. Then slide the hitch
tube up or down to new set of holes. Replace bolts and nuts.
DANGER! Be sure that the hitch and safety chains are
secure before towing the sawmill. Always connect the
break-away cable to the vehicle when towing the sawmill.
Failure to do so may result in serious personal injury and/or
severe machine damage.
DANGER! Make sure all brake and light connections have
been made and are working properly before towing the
sawmill. Failure to do so may result in serious personal
injury and/or severe machine damage. Make sure you have
complied with all applicable Federal, State and Local motor
vehicle safety laws.
DANGER! Chock the mill to prevent movement before
unhitching it from the towing vehicle. Failure to do so may

Surge Brake Hitch
Operation
Surge Brake Hitch SBS97doc091818 1-3
1
result in serious injury or death.
WARNING! Always check trailer tires for proper inflation
before towing sawmill. Failure to do so may lead to tire fail-
ure resulting in property damage and/or serious injury or
death.

Maintenance
1
1-1 SBSdoc091818
1.2 Maintenance
1. Clean and repack the trailer axle wheel bearings with lithium grease every 12 months or
12,000 miles (19,308 km), whichever comes first.
2. Make sure that the trailer tires are correctly inflated to the pressure shown on the tire.
CAUTION! Always check trailer tires for proper inflation
before towing sawmill. Failure to do so may result in
machine damage.
3. Check the adjustment of the trailer hitch coupler bracket frequently and adjust if neces-
sary. Replace any bent or otherwise damaged parts before using the hitch. Use only parts
provided by the hitch manufacturer for this hitch model.
4. The trailer brakes should be adjusted as follows:
after the first 200 miles of operation when the brake shoes and drums have
“seated,”
at 3,000 mile intervals,
or as use and performance requires.
The brakes should be adjusted in the following manner:
1. Jack up the trailer and secure on adequate capacity jack stands. Follow the trailer manu-
facturer's recommendations for lifting and supporting the unit. Make sure the wheel and
drum rotates freely.
CAUTION! Do not lift or support trailer on any part of the
axle or the suspension system. Never crawl under your
trailer unless it is resting on properly placed jack stands.
2. Remove the adjusting hole cover from the adjusting slot on the bottom of the brake back-
ing plate.
3. With a screwdriver or standard adjusting tool, rotate the star wheel of the adjuster assem-
bly to expand the brake shoes. Adjust the brake shoes out until the pressure of the linings
against the drum makes the wheel very difficult to turn. NOTE: For drop spindle axles, a
modified adjusting tool may be necessary.
4. Rotate the star wheel in the opposite direction until the wheel turns freely with a slight lin-
ing drag.

Maintenance
SBSdoc091818 1-2
1
5. Replace the adjusting hole cover and lower the wheel to the ground.
6. Repeat the above procedure on all brakes. For best results, the brakes should all be set
at the same clearance.
The wheel nut torque should be 90lbs.-ft. Tighten in 3 stages.
See Table 1-1. The wheel torque requirements are shown below.
Tighten bolts or nuts in the sequence shown for Wheel Torque Requirements.
See Figure 1-2.
Wheel Torque Sequence
Size 1st Stage 2nd Stage 3rd Stage
12” 25 35 50
13” 25 35 50
14” 25 50 90
15” 25 50 90
16” 25 50 90
TABLE 1-1
FIG. 1-2
SM0409
11
4
43
3
2
25
4 BOLT 5 BOLT

Maintenance
1
1-3 SBSdoc091818
If applicable, grease the Fine Adjust Outriggers (FAOs) every 200 hours of operation or
once a month, whichever comes first. Use one squeeze of a NLGI No. 2 grade lithium
grease from a grease gun to lubricate the outrigger and remove any sawdust.
See Figure 1-3.
Pre-2008 Style Fine Adjust Outriggers (Optional)
If applicable, grease the Fine Adjust Outriggers (FAOs) every 200 hours of operation or
once a month, whichever comes first. Use one squeeze of a NLGI No. 2 grade lithium
grease from a grease gun to lubricate the outrigger and remove any sawdust.
See Figure 1-4. To access the outrigger grease fitting, raise the outrigger base all the
way. The grease fitting will be accessible through the lowest outrigger hole.
FIG. 1-3
FIG. 1-4
SM0336-2
Grease Fitting
SM0214
Grease Fitting

Parts Lists
Trailer Hitch Assembly, Surge Brake
Parts Lists SBS97doc091818 2-1
2
SECTION 2 PARTS LISTS
2.1 Trailer Hitch Assembly, Surge Brake
REF DESCRIPTION (Indicates Parts Available In Assemblies Only) PART # QTY.
1 HITCH WELDMENT, SURGE BRAKE 015398 1
Chain, Safety w/Hook A07563 2
2Bolt, 1/2-13 X 4 1/2" Hex Head Grade 5 F05008-35 2
3Nut, 1/2-13 Hex Nylon Lock F05010-8 2
4 ACTUATOR, DICO SURGE BRAKE HITCH P09840 1
Bolt, Surge Brake Latch P10119 1
Bracket, Surge Bracke Latch (Lever Hitch) P12816 1
Spring, Surge Brake Latch (Lever Hitch) P12814 1
5Cable Assembly, Surge Brake Safety (Lever Hitch) P12815 1
6Hook, Surge Brake Safety Cable P12075 1
Damper, Surge Brake P10124 1
Fitting, Surge Brake Hitch Line P10370 1
7 BOLT, 58-11 X 6" HEX HEAD GRADE 5 F05009-22 2
SM0184D
4
1
5
6
7
7
8
8
8
910
2
3

Parts Lists
Trailer Hitch Assembly, Surge Brake
2
2-2 SBS97doc091818 Parts Lists
8 WASHER, 5/8” SAE FLAT F05011-5 1 4
9 NUT, 5/8-11 NYLON LOCK F05010-34 2
10 WASHER, 5/8” SPLIT LOCK F05011-27 2
TOWING EXTENSION KIT (NOT SHOWN, OPTIONAL) K12571 1
Bolt, 5/8-11 x 2 1/2" Hex Head Grade 5 F05009-20 2 
Washer, 5/8" Split Lock F05011-27 2
Washer, 5/8" SAE Flat F05011-5 2
Bracket, Safety Chain Bumper S12289-N 2 
Nut, 5/8-11 Free Hex F05010-5 2
DECAL, PINCH POINT DANGER P10287 1
DECAL, BEFORE TOWING DANGER (HYDRAULIC MILLS ONLY) P11809 1
1 Added LT30HD/40HD Super rev. H1.00+.

Parts Lists
Trailer Axle Assembly, Surge Brake
Parts Lists SBS97doc091818 3-3
3
2.2 Trailer Axle Assembly, Surge Brake
LT30 Super Rev. H4.00+
LT40 Super Rev. H5.00+
LT30HD Rev. H8.00+
LT40HD Rev. H8.00+
LT30HD Super Rev. H8.00+
LT40HD Super Rev. H8.00+
LT50HD Rev. A1.00+
REF DESCRIPTION (INDICATES PARTS AVAILABLE IN ASSEMBLIES ONLY) PART # QTY.
PLUMBING KIT, LT30/60 LENGTH SURGE BRAKE K10048 1
PLUMBING KIT, LT40/70 LENGTH SURGE BRAKE K10049 1
1
2
3
4
6
5
7
8
9
10
11
11
12
12
13
13
13
13
14
14
15
15
16
17
18
19
20
20
22
21
23
24
25
26
26
27
28
29
SM0275B

Parts Lists
Trailer Axle Assembly, Surge Brake
3
3-4 SBS97doc091818 Parts Lists
AXLE ASSEMBLY, 5200 LB SURGE BRAKE 014681 1
1Frame Weldment, Trailer Axle Painted (SUPER SURGE BRAKE) 015204 1 
Mount Bracket, Trailer Fender (requires welding) W09784 2
2Axle, 5200 Lb Drop Surge (SUPER SURGE BRAKE) 014679 1
3Spring, 2600 Lb. Dexter Leaf Drive Side (SUPER SURGE BRAKE) 015695 1
4Spring, 3000 Lb. Dexter Leaf Idle Side (SUPER SURGE BRAKE) 015694 1
Bearing Kit, Sawmill Axle Spindle (SUPER SURGE BRAKE) 015696 1
5Bearing, Dexter #22580 015697 1 
6Bearing, Dexter #LM67048 015699 1 
7Race, Inner Dexter #25520 015698 1 
8Race, Outer Dexter #LM67010 015700 1 
9Seal, Wheel Bearing Dust Dexter #10-1 015701 1
10 Cap, Wheel Bearing Dust (SUPER SURGE BRAKE) 015702 2
Shoe/Lining Kit, 10” x 2 1/4” Brake 010180 2
11 Wheel Assembly, Goodyear ST225/75R15 (SUPER SURGE BRAKE) 015988 2
12 Plate, Trailer Axle Shackle M07528 4
13 Bolt, 9/16-8 X 3" Shackle P04644 6
14 Nut, 9/16-8 Shackle P04643 6
15 Nut, 1/2-20 Wheel Lug P04646 10
16 BOLT, 1/2-13 X 4” HEX HEAD F05008-26 4
17 WASHER, 1/2” EXTERIOR STAR F05011-39 4
18 WASHER, 1/2" SAE FLAT F05011-2 4
19 NUT, 1/2-13 HEX NYLON LOCK F05010-8 4
FENDER ASSEMBLY, SUPER W/MUD FLAP 015950 2
20 Fender Weldment, Trailer Wheel (Super Surge Brake) 015788 2
21 Plate, Mud Flap Retaining 015787 2
22 Flap, Mud 015758 2
23 Screw, #10-24 x 5/8” Hex Head F05004-18 6
24 Nut, #10-24 Self-Locking Hex F05010-14 6
25 Strap, 6” Rubber 016542 2
26 Washer, 1/4” SAE Flat F05011-11 2
27 Bolt, 1/4-20 x 1 1/4” Hex Head Full Thread F05005-3 1
28 Nut, 1/4-20 Lock F05010-21 1
29 DECAL, FENDER DAMAGE CAUTION S11761 2
DECAL, PINCH POINT DANGER P10287 1
DECAL, REMOVE FENDERS (CONTROL BOX) 076607 1

Parts Lists
Trailer Axle Assembly, Surge Brake
Parts Lists SBS97doc091818 3-5
3
2.3 Trailer Axle Assembly, Surge Brake
LT30HD Rev. G1.00 - H7.00
LT40HD Rev. G1.00 - H7.00
LT30HD Super Rev. G1.00 - H7.00
LT40HD Super Rev. G1.00 - H7.00
REF DESCRIPTION (INDICATES PARTS AVAILABLE IN ASSEMBLIES ONLY) PART # QTY.
PLUMBING KIT, LT30/60 LENGTH SURGE BRAKE K10048 1
PLUMBING KIT, LT40/70 LENGTH SURGE BRAKE K10049 1
AXLE ASSEMBLY, 5200 LB SURGE BRAKE 014681 1
1Frame Weldment, Trailer Axle Painted (SUPER SURGE BRAKE) 015204 1 
Mount Bracket, Trailer Fender (requires welding) W09784 2
2Axle, 5200 Lb Drop Surge (SUPER SURGE BRAKE) 014679 1
3Spring, 3000 Lb. Dexter Leaf Idle Side (SUPER SURGE BRAKE) 015694 1
4Spring, 2600 Lb. Dexter Leaf Drive Side (SUPER SURGE BRAKE) 015695 1
1
2
4
3
6
10
5
8
7
9
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
3H0467B

Parts Lists
Trailer Axle Assembly, Surge Brake
3
3-6 SBS97doc091818 Parts Lists
Bearing Kit, Sawmill Axle Spindle (SUPER SURGE BRAKE) 015696 1
5Bearing, Dexter #22580 015697 1 
6Bearing, Dexter #LM67048 015699 1 
7Race, Inner Dexter #25520 015698 1 
8Race, Outer Dexter #LM67010 015700 1 
9Seal, Wheel Bearing Dust Dexter #10-1 015701 1
10 Cap, Wheel Bearing Dust (SUPER SURGE BRAKE) 015702 2
Shoe/Lining Kit, 10” x 2 1/4” Brake 010180 2
11 Wheel Assembly, Goodyear ST225/75R15 (SUPER SURGE BRAKE) 015988 1 2
12 Plate, Trailer Axle Shackle M07528 4
13 Bolt, 9/16-8 X 3" Shackle P04644 6
14 Nut, 9/16-8 Shackle P04643 6
15 Nut, 1/2-20 Wheel Lug P04646 10
16 BOLT, 1/2-13 X 4” HEX HEAD F05008-26 4
WASHER, 1/2” EXTERIOR STAR F05011-39 4
17 WASHER, 1/2" SAE FLAT F05011-2 4
18 NUT, 1/2-13 HEX NYLON LOCK F05010-8 4
FENDER ASSEMBLY, SUPER W/MUD FLAP 015950 2
19 Fender Weldment, Trailer Wheel (Super Surge Brake) 015788 2 2
20 Plate, Mud Flap Retaining 015787 2
21 Flap, Mud 015758 2
22 Screw, #10-24 x 5/8” Hex Head F05004-18 6
23 Nut, #10-24 Self-Locking Hex F05010-14 6
24 DECAL, FENDER DAMAGE CAUTION S11761 2
PIN, 5/16” X 1” DETAINING F05012-45 2
1 015988 wheel assembly replaces H78x15 LRD wheel assembly (015448) originally supplied before LT30HD/40HD Super Rev.
G7.00.
2 Fender revised to increase clearance between brace and tire; mud flaps added. Replaces 015112 originally supplied until LT30 Super
rev. F9, LT40 Super rev. G1, LT30HD Super and LT40HD Super rev. G3.

Parts List
Outriggers
Parts List SBS97doc091818 3-7
3
2.4 Outriggers
LT70HD Rev. A1.00+
REF DESCRIPTION (INDICATES PARTS AVAILABLE IN ASSEMBLIES ONLY) PART # QTY.
1 OUTRIGGER ASSEMBLY, LONG (See Section 2.5)012997 1
OUTRIGGER ASSEMBLY, LONG (SUPER LT30HD ONLY) (See Section 2.10)016414 1
2 OUTRIGGER ASSEMBLY, LONG (See Section 2.5)012997 1
3 OUTRIGGER ASSEMBLY, SHORT (See Section 2.11)A04278 1
4 OUTRIGGER ASSEMBLY, SHORT W/JACK HOLDER (See Section 2.15)A09475 1
5 OUTRIGGER ASSEMBLY, LONG FRONT (See Section 2.8)015143 1
6 OUTRIGGER ASSEMBLY, LONG REAR (See Section 2.13)A12083 1
230026-1C
12
3
4
12
3
4
5
6
LT25/LT30/LT30HD/LT60HD (16’ Bed)
LT25L/LT27/LT40/LT40HD/LT70HD (24’ Bed)

Parts List
Outrigger Assembly, Long
3
3-8 SBS97doc091818 Parts List
2.5 Outrigger Assembly, Long
LT30HD Rev. H6.00+
LT40HD Rev. H6.00+
LT30HD Super Rev. H6.00+
LT40HD Super Rev. H6.00+
LT50HD Rev. A1.00+
LT70HD Rev. A1.00+
REF DESCRIPTION (INDICATES PARTS AVAILABLE IN ASSEMBLIES ONLY) PART # QTY.
OUTRIGGER ASSEMBLY, LONG 012997 1 1/2
1Guide, Long Outrigger Guide 012996 1
2Leg, Outrigger 016401 1
3Cap, Outrigger Leg P09926 1
4Spring, Outrigger Pin 016145 1
Pin Kit, 3/4” Outrigger Pull 016148 1
1
2
3
4
5
67
8
10
9
3H0807B

Parts List
Outrigger Assembly, Long
Parts List SBS97doc091818 3-9
3
5Pin, 3/4” Outrigger Pull 016147 1 
6Pin, 5/16" X 2 1/2" Roll F05012-47 1
7Pin, 3/16" X 1 3/4" Roll F05012-1032 1
Pin, 1/8” x 1 1/4” Cotter F05012-5921
8 BOLT, 3/8-16 X 5” CARRIAGE HEAD F05007-113 4/8
9 WASHER, 3/8” SAE FLAT F05011-3 4/8
10 NUT, 3/8-16 HEX NYLON LOCK F05010-10 4/8
1 Washers (2) removed from spring to improve outrigger locking pin operation (LT30HD/40HD Rev. H6.01, LT30HD/40HD Super Rev.
H6.01). Washers may be removed on previous revisions with 3/4” diameter locking pins to improve operation.
2 Use F05012-103 3/16" X 1 3/4" Roll Pin for LT30HD/40HD H6.02, LT30HD/40HD Super H6.02 and later revision mills. Use
F05012-59 1/8” x 1 1/4” Cotter Pin for all prior revision mills.

Parts List
Outrigger Assembly, Long
3
3-10 SBS97doc091818 Parts List
2.6 Outrigger Assembly, Long
LT30HD Rev. G9.00 - H5.00
LT40HD Rev. G9.00 - H5.00
LT30HD Super Rev. H1.00 - H5.00
LT40HD Super Rev. H1.00 - H5.00
REF DESCRIPTION (INDICATES PARTS AVAILABLE IN ASSEMBLIES ONLY) PART # QTY.
OUTRIGGER ASSEMBLY, LONG 012997 1 1/2
1Guide, Long Outrigger Guide 012996 1
2Leg, Outrigger W07537 1
3Cap, Outrigger Leg P09926 1
4Spring, Outrigger Pin 016145 1
5Washer, 3/4" SAE Flat F05011-62 2 2
Pin Kit, 3/4” Outrigger Pull 016148 1
1
2
3
54
6
78
9
11
10
SM0136B