Woodstock W1782 User manual
Phone: (360) 734-3482 • Online Technical Support: [email protected]
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED DECEMBER, 2007 (JM)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9571BL Printed in China
MODEL W1782
34˚ ANGLE
FINISH NAILER
OWNER'S MANUAL
Find and replace list
Find Examples to Replace With
W1782 W1736
34˚ Framing Nailer 18 Gauge Stapler Kit
Nailer Stapler
Model W1782 34˚ Angle Finish Nailer
-1-
Safety Instructions for Pneumatic Tools
1. KEEP ALL SAFETY DEVICES IN
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking
to see that keys and adjusting
wrenches are removed from tool
before operation.
3. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
4. DO NOT USE IN DANGEROUS
ENVIRONMENT. Do not use
pneumatic tools in damp or wet
locations, or where any flammable
or noxious fumes may exist. Keep
work area well lighted.
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept at a safe distance
from work area.
6. MAKE WORKSHOP CHILD PROOF by
locking your shop and shutting off
air valves.
7. DO NOT FORCE TOOL. It will do
the job better and safer at the rate
for which it was designed.
8. USE THE RIGHT TOOL. Do not
force tool or attachment to do a
job for which it was not designed.
9. DO NOT USE UNDER THE
INFLUENCE OF DRUGS OR
ALCOHOL.
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are intended
to convey the level of importance of the safety messages. The progression of
symbols is described below. Remember that safety messages by themselves do not
eliminate danger and are not a substitute for proper accident prevention measures.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
NOTICE This symbol is used to alert the user to useful
information about proper operation of the
equipment.
Model W1782 34˚ Angle Finish Nailer
-2-
10. USE PROPER AIR HOSE for the
tool. Make sure your air hose is in
good condition and is long enough
to reach your work without
stretching.
11. WEAR PROPER APPAREL. Do
not wear loose clothing, gloves,
neckties, rings, bracelets, or
other jewelry which may get
caught in moving parts. Non-slip
footwear is recommended. Wear a
protective hair covering to contain
long hair.
12. ALWAYS USE SAFETY GLASSES.
Also use a face or dust mask
if cutting operation is dusty.
Everyday eyeglasses only have
impact resistant lenses, they are
NOT safety glasses.
13. WEAR APPROVED HEARING
PROTECTION. Air escaping from
pneumatic tools can exceed safe
exposure limits and may cause
hearing damage with prolonged
exposure.
14. SECURE WORK. Use clamps or a
vise to hold work when practical.
It is safer than using your hand
and frees both hands to operate
tool.
15. MAINTAIN TOOLS WITH CARE.
Keep tools lubricated and clean
for best and safest performance.
Follow instructions for lubricating
and changing accessories.
16. REDUCE THE RISK OF
UNINTENTIONAL FIRING. Do not
carry tool with hand on trigger
and always disconnect from air
when not in use.
17. DISCONNECT TOOLS before servic-
ing, changing accessories, or mov-
ing to another location.
18. DO NOT OVERREACH. Keep proper
footing/balance at all times.
19. USE THE RECOMMENDED
ACCESSORIES. Consult owner’s
manual for recommended acces-
sories. The use of improper acces-
sories may cause risk of injury.
20. CHECK FOR DAMAGED PARTS
BEFORE USING. Check for binding
and alignment of parts, broken
parts, part mounting, loose bolts,
and any other conditions that may
affect machine operation. Repair
or replace damaged parts.
21. NEVER LEAVE UNATTENDED TOOL
CONNECTED TO AIR. Disconnect
the air hose and do not leave tool
until it is relieved of any built up
pressure.
22. NEVER ALLOW UNTRAINED
USERS TO USE THIS TOOL WHILE
UNSUPERVISED.
23. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING TOOL. Seek formal training
or research books or magazines
that specialize in pneumatic tools.
24. BE AWARE OF HOSE LOCATION
WHEN USING PNEUMATIC TOOLS.
Hoses can easily become a tripping
hazard when laid across the floor
or spread out in a disorganized
fashion.
Safety Instructions for Pneumatic Tools
Model W1782 34˚ Angle Finish Nailer
-3-
1. HAND INJURIES: Do not place your
hands near the nail point of entry.
A nail can deflect and tear through
the surface of the workpiece,
puncturing your hand or fingers.
2. COMBUSTIBLE GASES: Never
connect the nailer to pressurized
oxygen or other combustible
gases as a power source. Only use
filtered, lubricated, and regulated
compressed air.
3. SAFE HANDLING: Never point
the nailer at others! Do not keep
the trigger pulled when loading
fasteners, carrying, or holding
tool. Carry the nailer only by the
handle, never by any other part.
Do not carry the nailer by the air
hose. Disconnect the nailer from
the air hose when going up and
down ladders.
4. CLEANING: Never use gasoline or
other flammable liquids to clean
the nailer; vapors in the nailer will
ignite by a spark and cause it to
explode.
Additional Safety Instructions for Nailers
5. HOSE USAGE: Make sure your air
hose is designed for the tool in
use, is in good condition, and is
long enough to reach your work
without stretching. However, an
overly long air hose in the work
area may be a tripping hazard.
6. OPERATING QUESTIONS: If you
are not sure about the intended
operation, stop using the nailer.
Seek formal training.
7. MAINTENANCE: Always disconnect
air from the nailer when servicing
or installing nails. During
maintenance, a nailer connected to
air may fire accidentally, causing
serious personal injury.
8. COMPRESSED AIR RATING: Do not
connect the nailer to compressed
air that exceeds 120 PSI.
9. CHECK VALVE: Do not use a check
valve or any other fitting that
allows air to remain in the tool.
10. MODIFICATION: Do not modify
this tool or bypass the safety nose
mechanism.
Never point this nailer at yourself
or another person! Always pay
attention to the direction this nailer
is pointed. Use this tool with respect
and caution to lessen the possibility
of operator or bystander injury.
Ignoring this warning may result in
serious personal injury.
Nailer accidents routinely happen
while moving the gun to another
location, such as up ladders, to
another room, or even another job
site. Always disconnect the gun
immediately after use and never
transport the gun while connected to
the air—even if the air compressor is
disconnected from its power source!
Model W1782 34˚ Angle Finish Nailer
-4-
No list of safety guidelines can be
complete. Every shop environment
is different. Always consider safety
first, as it applies to your individual
working conditions. Use this and
other tools with caution and respect.
Failure to do so could result in serious
personal injury, damage to equipment
or poor work results.
INTRODUCTION
Woodstock Technical
Support
Tool Data
Nail Size ................15 gauge finish nails
Nail Length ........................... 1¼"-2½"
Magazine Capacity ................... 40 Nails
Air Inlet .................................¼" NPT
Dimensions .......... 2.92" x 10.43" x 16.14"
Weight ..................................5¼ lbs.
Operating Pressure ............... 60-100 PSI
Read the manual before operation.
Become familiar with this nailer, its
safety instructions, and its operation
before beginning any work. Serious
personal injury may result if safety
or operational information is not
understood or followed.
This tool has been specially designed to
provide many years of trouble-free ser-
vice. Close attention to detail, ruggedly
built parts and a rigid quality control pro-
gram assure safe and reliable operation.
Woodstock International, Inc. is commit-
ted to customer satisfaction. Our intent
with this manual is to include the basic
information for safety, setup, operation,
maintenance, and service of this product.
We stand behind our tools! In the
event that questions arise about
your tool, please contact Woodstock
International Technical Support at
(360) 734-3482 or send e-mail to:
tech-support@shopfox.biz. Our knowl-
edgeable staff will help you troubleshoot
problems and process warranty claims.
If you need the latest edition of this
manual, you can download it from
http://www.shopfox.biz.
If you have comments about this
manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation
Manager
P.O. Box 2309
Bellingham, WA 98227
Email: manuals@woodstockint.com
Model W1782 34˚ Angle Finish Nailer
-5-
The Model W1782 is designed to be
operated at 60-100 PSI using clean,
dry, regulated, compressed air. Do not
exceed the 120 PSI maximum operating
pressure for your model.
Before using your new nailer, regulate
the air pressure to find the optimum
setting within the specified operating
range. Start by testing the nailer at a low
setting, then increase the air pressure as
needed for satisfactory results.
An in-line filter/lubricator/regulator unit
can be installed as depicted in Figure 1.
This filter/lubricator/regulator unit
will protect your tool from damaging
water build-up, allow you to adjust and
maintain regulated air pressure to your
tool, and save you the inconvenience of
having to manually lubricate your tool
every time you use it.
If you plan on installing a filter/
lubricator/regulator unit in your
compressed air system, always follow the
connection instructions that come with
the unit.
Figure 1. Typical filter/lubricator/regulator installation order.
Compressed Air System
Exceeding the maximum permissible
operating pressure may damage the
nailer and cause it to malfunction.
To protect yourself from personal
injury, DO NOT allow the air pressure
to exceed the recommended
pressure for this nailer!
Model W1782 34˚ Angle Finish Nailer
-6-
SETUP
Inventory
This tool has been carefully packaged for safe transportation. If you notice the tool
has been damaged during shipping, please contact your authorized Shop Fox dealer
immediately.
Unpacking
The following is a description of the main components shipped with the Model W1782.
Lay the components out to inventory them.
Note: If you can't find an item on this list, check the mounting location on the tool
or examine the packaging materials carefully. Occasionally we pre-install certain
components for safer shipping.
Box Inventory (Figure 2) Qty
A. 34° Angle Finish Nailer ................ 1
B. Safety Goggles .......................... 1
C. Oil ......................................... 1
Qty
D. Hex Wrenches 3, 4, 5mm .......... 1 ea
E. Case ....................................... 1
Figure 2. Model W1782 inventory.
E
A
B
C
D
Model W1782 34˚ Angle Finish Nailer
-7-
A safety mechanism on the nose of
the nailer protects against accidental
firing. When the trigger is pressed, the
nailer will not fire until the safety nose
mechanism is depressed.
Before you use your nailer for the first
time, check the safety nose mechanism
to ensure proper function.
To check the safety nose mechanism,
do these steps:
1. DISCONNECT NAILER FROM THE AIR
SUPPLY!
2. Make sure the magazine is empty and
contains no nails.
3. Make sure the trigger and the safety
nose mechanism move up and down
without sticking.
4. Connect the nailer to the air supply.
5. Without pressing the trigger,
depress the safety nose mechanism
against a scrap piece of wood that is
clean and free of any knots, nails, or
other foreign objects.
— If the nailer does not fire, then
the safety nose mechanism is
working correctly.
— If the nailer does fire when you do
this, immediately disconnect the
nailer from the air supply and call
Technical Support.
Safety Nose Mechanism — If the nailer fires when the trigger
is pulled, without the safety nose
mechanism being depressed, then
the nailer is not working properly.
— If you find that the safety
nose mechanism is not working
properly, check the lubrication of
its sliding components.
The safety mechanism is a mechanical
device that can fail. Never rely on this
mechanism as an excuse to point the
nailer at yourself or any bystanders.
Serious injury may occur.
Operating this nailer can propel
objects into the air, causing immediate
eye damage. To protect yourself,
always wear ANSI approved safety
glasses or goggles when operating this
equipment.
Do not attempt to modify or bypass
the safety nose mechanism to make
the nailer fire without pushing the
nose down.
Model W1782 34˚ Angle Finish Nailer
-8-
OPERATIONS
Loading
When replacing nails in your Model
W1782, follow these guidelines:
Gauge: ........................................15
Length: ............................. 11⁄4" -21⁄2"
Capacity: .............................. 40 Nails
Angle: ...................................... 34°
To load your nailer, do these steps:
1. DISCONNECT NAILER FROM THE AIR
SUPPLY!
2. Insert a nail stick into the T-slot at
the top of the magazine as shown in
Figure 3.
If you have not read the safety
instructions in this manual, do not
operate the nailer.
Before you operate your nailer, place a
drop of the included oil into the quick
connect fitting where the nailer connects
to the air supply, unless using a lubricator
unit.
To operate your nailer, do these steps:
1. Connect the air supply to the quick
connect fitting.
2. To test for proper nail penetration,
hold the nailer perpendicular to the
surface of a piece of clean scrap
wood that is thick enough for the
length of nails you have loaded.
3. Depress the safety nose mechanism
against your workpiece.
4. Before pulling the trigger, make sure
your free hand and other body parts
are positioned out of the way of a
potential path of a nail in case of
deflection.
Deflection is caused when grain
irregularities, knots or foreign objects
inside the wood cause the nail to
change its path, resulting in the
nail puncturing the surface of the
workpiece, as shown in Figure 4.
Operating
4. Pull the magazine pusher all the way
back, then let it come forward until
it rests against the end of the nail
stick.
3. Slide the nail stick all the way down
to the nose of the nailer.
Figure 3. Loading finish nails into nailer.
Pusher
Model W1782 34˚ Angle Finish Nailer
-9-
5. Pull the trigger.
— If the nail drove into the wood
far enough, continue with your
intended operations.
— If the nail either went too far or
not far enough, then go to the
Adjusting Depth section on this
page.
Figure 4. Example of nail deflection.
A depth adjustment knob is attached to
the nose for setting the nail depth.
To adjust the depth, do these steps:
1. DISCONNECT NAILER FROM THE AIR
SUPPLY!
2. Rotate the adjustment knob (Figure
5) clockwise to increase nail depth
or counterclockwise to decrease nail
depth.
Adjusting Depth
3. Connect nailer to the air supply and
test the nail depth. Repeat this entire
procedure if necessary until the nail
depth is satisfactory.
Figure 5. Loosening cap screw for depth
adjustment.
Depth
Adjustment Knob
Besides damaging your workpiece,
deflection can cause injury if your
free hand is securing the workpiece in
the location that the nail deflects.
DO NOT place your hands near the
nail point of entry. A nail can deflect
and tear through the surface of the
workpiece, puncturing your hand or
fingers.
Model W1782 34˚ Angle Finish Nailer
-10-
A jammed nail must be cleared before
using the nailer again.
To clear a jammed nail from the dis-
charge area, do these steps:
1. DISCONNECT NAILER FROM THE AIR
SUPPLY!
2. Push the finger tab (Figure 6) inside
the magazine pusher, pull the pusher
back slightly to clear it of the nail
stick. While pressing the finger tab,
slide the pusher forward over the
nails until it rests near the nose.
Clearing Jammed Nails 5. Flip up the quick release latch
located on top of the nailer nose
assembly, as shown in Figure 7.
Figure 6. Finger tab and backstop.
Finger Tab
Backstop
3. Continue pressing the finger tab, and
push the nails up the magazine until
they are released from the pusher.
4. Depress the backstop (Figure 6)
inside the magazine and slide the nail
stick out of the magazine.
Figure 7. Releasing quick release latch.
Figure 8. Removing driver guide cover.
7. Remove the jammed nail from the
discharge area with needle nose pli-
ers.
8. Throw the damaged nail away and
insert a new nail stick that only
contains clean, undamaged nails. DO
NOT use dirty or damaged nails!
9. Replace the driver guide cover and
snap the quick release latch back into
operating position.
6. Remove the driver guide cover
(Figure 8).
Model W1782 34˚ Angle Finish Nailer
-11-
Replacing Piston and
O-Rings
Under heavy use, a piston or piston shaft
may wear out. Replacement is quick and
easy. Contact your authorized Shop Fox
dealer to obtain the Piston Repair Kit
(part number X1782001).
To replace a piston and O-rings, do
these steps:
1. DISCONNECT NAILER FROM THE AIR
SUPPLY!
2. Remove all nails from the magazine
cartridge, and clean the exterior of
the nailer.
3. Remove the four cap screws on the
back of the nailer, near the exhaust
port.
4. Remove the cap.
5. The top of the piston should now be
visible inside the cylinder, which is
housed in the head of the nailer.
Always disconnect nailer from air
whenever servicing! During main-
tenance, a nailer connected to air
may fire accidentally, causing seri-
ous personal injury!
6. Open the nose cover as if to clear a
jammed nail.
7. Watch the discharge area and push
the top of the piston with your
finger. You will see the piston shaft
slide down the discharge area.
8. Taking care not to scratch or dent
the nailer parts, use a wooden dowel
or similarly shaped tool to push the
piston shaft back inside the nailer
until you can grip the piston head and
remove it from the cylinder. Clean
and inspect the parts for cracks,
wear, or burrs.
9. Place a new O-ring on the new piston
and apply a thin film of the nailer
lubricating oil on the O-ring.
10. Insert the new piston in the cylinder.
Make sure that the grooves on the
piston shaft line up with those on the
guide at the bottom of the cylinder.
The new piston should easily slide
into the cylinder. DO NOT force the
piston into the cylinder! If the piston
is not easily inserted, double-check
the alignment of the piston shaft with
the grooves on the guide.
11. After the piston is inserted correctly,
close the magazine. Replace the rear
cap assembly and tighten the four
cap screws.
12. For more assistance, or to install a
complete O-ring set, refer to the
appropriate breakdown diagram in
the back of this manual for O-ring
locations.
Model W1782 34˚ Angle Finish Nailer
-12-
CLEANING & LUBRICATION
Cleaning
Use a good solvent to clean the nose
assembly of the nailer. Always be sure
that the nailer is dry before using it
again.
Do not allow dust, chips, sand, etc.
into the air connectors or into the body
of the nailer; this may result in leaks
and damage to the nailer and the air
couplings.
Lubricating
Standard pneumatic tool oil has been
included with your new Shop Fox nailer
to help maintain its useful life. Place two
to six drops of oil in the nailer air inlet
(as shown in Figure 9) before every use,
or after 2 hours of continuous use.
Figure 9. Lubricating nailer via air inlet.
Never clean this tool with gasoline
or other flammable liquids. Vapors
in the tool may ignite, causing
the tool to explode. Ignoring
this warning may lead to serious
personal injury or even death!
Wipe off any excess oil near the nailer
exhaust to avoid dust build-up. When the
oil that was included with the nailer has
been completely used, replace with a
quality pneumatic tool oil.
An alternative to manual oiling is to
install a lubricator in your air compressor
line. A lubricator eliminates the need to
oil your tool each time you use it. If you
have a lubricator in your air compressor
line, ensure it is functioning properly.
Model W1782 34˚ Angle Finish Nailer
-13-
PARTS BREAKDOWN
Model W1782 34˚ Angle Finish Nailer
-14-
PARTS LIST
REF PART�# DESCRIPTION REF PART�# DESCRIPTION
1 X1782001 PISTON�REPAIR�KIT 49 X1782049 JOINT�SEAT
2 X1782002 AIR�PLUG�CASE 50 X1782050 ROLL�PIN�3�X�28�
3 X1775007 1/4"�NPT�MALE�CONNECT 51 X1782051 SAFETY�SPACER
4 XPSB53M CAP�SCREW�M5-.8�X�18 52 X1782052 TRIGGER
5 X1782005 END�CAP 53 X1782053 ROLL�PIN�3�X�17
6 X1782006 END�CAP�WASHER 54 X1782054 TRIGGER�VALVE�SEAT
7 X1782007 RUBBER�HANDLE�CASE 55 X1782055 O-RING�20.3�X�2.3
8 X1782008 SUPPORT�SEAT 56 X1782056 SWITCH�VALVE�STEM
9 XPW02M FLAT�WASHER�5MM 57 X1782057 SWITCH�VALVE�SPRING
10 XPSB33M CAP�SCREW�M5-.8�X�12 58 X1782058 O-RING�2.5�X�1.5
11 X1782011 LOCK�NUT�M4-.7 59 X1782059 TRIGGER�VALVE�GUIDE
12 XPRP69M ROLL�PIN�3�X�35 60 X1782060 O-RING�9�X�1.8
13 X1782013 PUSHER 61 X1782061 O-RING�6.4�X�2
14 X1782014 SPRING�CORE 62 X1782062 O-RING�6.2�X�1.8
15 X1782015 TORSION�SPRING 63 X1782063 TRIGGER�VALVE�SEAT
16 X1782016 PIN�3�X�35 64 X1782064 O-RING�17.4�X�1.5
17 X1782017 TORSION�SPRING�65 X1782065 O-RING�15�X�2.65
18 X1782018 SLIDE�SEAT 66 X1782066 RUBBER�WASHER
19 X1782019 FIXED�SEAT 67 X1782067 BODY
20 X1782020 SPRING�SLICE 68 X1782068 GASKET
21 XPS101M PHLP�HD�SCR�M4-.7�X�7 69 X1782069 GUIDE�WASHER
22 X1782022 MAGAZINE 70 X1782070 BUMPER
23 X1782023 LOCK�NUT�M5-.8 71 X1782071 PISTON
24 XPSB23M CAP�SCREW�M4-.7�X�12 72 X1782072 O-RING�34�X�3.55
25 X1782025 DRIVE�NAIL�SLICE 73 X1782073 CYLINDER
26 X1782026 DRIVE�GUIDE 74 X1782074 SEALING�WASHER
27 X1782027 PIN�4�X�25 75 X1782075 FIX�RING
28 X1782028 ROLL�PIN�3�X�24 76 X1782076 O-RING�67�X�2.7
29 X1782029 DRIVER�GUIDE�COVER 77 X1782077 COLLAR
30 X1782030 LATCH 78 X1782078 SEALING�WASHER
31 X1782031 QUICK�RELEASE�HANDLE 79 X1782079 SWITCH�VALVE
32 XPSB02M CAP�SCREW�M6-1�X�20 80 X1782080 O-RING�44.5�X�2.5
33 XPLW03M LOCK�WASHER�6MM 81 X1782081 O-RING�32.6�X�2.5
34 XPSB03M CAP�SCREW�M5-.8�X�8 82 X1782082 SWITCH�VALVE�SEAT
35 XPW05M FLAT�WASHER�4MM 83 X1782083 COMPRESSION�SPRING
36 XPSB110M CAP�SCREW�M4-.7�X�6 84 X1782084 CYLINDER�COVER
37 X1782037 SAFETY�NOSE 85 XPLW01M LOCK�WASHER�5MM
38 X1782038 SAFETY�STAND 86 XPSB38M CAP�SCREW�M5-.8�X�25
39 X1782039 COMPRESSION�SPRING 87 X1782087 RUBBER�WASHER�10�MM
40 X1782040 ADJUSTING�NUT 88 X1782088 AIR�DEFLECTOR
41 X1782041 DRIVE�STAND 89 X1782089 SPECIAL�CAP�SCREW�M5-.8�X�12
42 XPR39M EXT�RETAINING�RING�8MM 90 XPAW05M HEX�WRENCH�5MM
43 X1782043 DRIVE�PIN 91 XPAW04M HEX�WRENCH�4MM
44 X1782044 SAFETY�SEAT 92 XPAW03M HEX�WRENCH�3MM
45 X1782045 STEEL�BALL�2MM 93 X1782093 CARRYING�CASE
46 X1782046 COMPRESSION�SPRING 94 X1782094 SAFETY�GLASSES
47 X1782047 JOINT�BOLT 95 X1782095 COMPLETE�O-RING�SET
48 X1782048 FIXED�BLOCK
Troubleshooting
Symptom Possible Cause Cause Possible Solution
Air leaking at
trigger valve area.
1. O-rings in trigger valve
housing are damaged.
1. O-rings must be replaced
& operation of safety nose
must be checked.
Air leaking
between housing
and hose.
1. Loose screws in housing.
2. Damaged O-ring.
3. Loose air fitting.
1. Reseal and tighten screws.
2. Replace O-ring.
3. Tighten air fitting & use
teflon tape.
Air leaking
between housing
and cap.
1. Damaged seal. 1. Replace damaged seals.
Tool skips nails
while discharging.
1. Excessive air pressure.
2. Air leaks.
3. Dirt in nose.
4. Dirt or damage prevents nails
from moving freely.
5. Inadequate air flow to tool.
6. Worn piston O-ring or lack of
lubrication.
7. Damaged trigger valve O-
rings.
8. Worn bumper.
9. Cap seal leaking.
1. Reduce air pressure to
tool.
2. Reseal and tighten screws
and fittings.
3. Clean nose.
4. Clean magazine and
inspect/repair damage.
5. Check fittings, hose,
compressor, and air
pressure.
6. Replace O-ring and
lubricate.
7. Replace trigger valve O-
rings.
8. Replace bumper.
9. Replace cap seal.
Tool runs slowly
or has a loss of
power.
1. Undersized air hose.
2. Nailer is not lubricated.
3. Broken spring in cap
assembly.
4. Exhaust port in cap is
blocked.
1. Use a larger hose.
2. Lubricate nailer.
3. Replace spring.
4. Clean or replace damaged
internal parts.
Fasteners
frequently jam the
nailer.
1. Nails are the wrong size.
2. Nails are bent or dirty.
3. Magazine or nose screws are
loose.
4. Driver or driver guide are
worn or damaged.
5. Nails are wrong angle.
1. Use correct nails.
2. Use undamaged, clean
nails.
3. Tighten magazine.
4. Replace worn or damaged
parts.
5. Use correct angle nails.
Nailer does not
fire.
1. Nailer is not lubricated.
2. Nail is jammed in magazine or
discharge area.
3. Piston shaft is damaged.
4. Air pressure too low.
1. Follow lubricating
instructions.
2. Clear nailer magazine or
discharge area.
3. Replace piston shaft.
4. Check/increase air
pressure.
Air blows out of
exhaust cap; nailer
will not fire.
1. O-ring slipped out of groove
or damaged inside nailer.
1. Reinstall/replace suspect
O-ring; turn down air
pressure.
CUT ALONG DOTTED LINE
Name ___________________________________________________________________________________
Street __________________________________________________________________________________
City _________________________ State ___________________________Zip ________________________
Phone # ______________________ Email __________________________Invoice # ___________________
Model #_________Serial #______________Dealer Name__________________Purchase Date___________
Warranty Registration
The following information is given on a voluntary basis. It will be used for marketing purposes to help us
develop better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
_____ Advertisement ____ Friend ____ Local Store
_____ Mail Order Catalog ____ Website ____ Other:
2. How long have you been a woodworker/metalworker?
_____ 0-2 Years _____ 2-8 Years ____ 8-20 Years _____ 20+ Years
3. How many of your tools or tools are Shop Fox?
_____ 0-2 _____ 3-5 ____ 6-9 _____ 10+
4. Do you think your tool represents a good value? _____ Yes ____ No
5. Would you recommend Shop Fox products to a friend? _____ Yes ____ No
6. What is your age group?
_____ 20-29 ____ 30-39 ____ 40-49
_____ 50-59 ____ 60-69 ____ 70+
7. What is your annual household income?
_____ $20,000-$29,000 ____ $30,000-$39,000 ____ $40,000-$49,000
_____ $50,000-$59,000 ____ $60,000-$69,000 ____ $70,000+
8. Which of the following magazines do you subscribe to?
9. Comments: __________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
___________________________________________________________________
___________________________________________________________________
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Modeltec
____ Old House Journal
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Practical Homeowner
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Rifle
____ Shop Notes
____ Shotgun News
____ Today’s Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Woodwork
____ Woodworker West
____ Woodworker’s Journal
____ Other:
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
FOLD ALONG DOTTED LINE
WOODSTOCK INTERNATIONAL INC.
P.O. BOX 2309
BELLINGHAM, WA 98227-2309
Place
Stamp
Here
FOLD ALONG DOTTED LINE
Table of contents
Other Woodstock Nail Gun manuals
Popular Nail Gun manuals by other brands
Hitachi
Hitachi NC 40G Handling instructions
DeWalt
DeWalt 20V MAX DCN890 instruction manual
Bostitch
Bostitch SMART POINT BTFP12233 Operation and maintenance manual
DeWalt
DeWalt DCN680 Original instructions
Hitachi
Hitachi NR 83A5 Instruction and safety manual
Chicago Electric
Chicago Electric 91494 Assembly and operating instructions
