WorkPro WPE Series User manual

WPE 24
User Manual
Version1.1

WPE 24
USER MANUAL
VERSION 1.1
WPE SERIES www.workpro.es 1
SAFETY INSTRUCTIONS
1. Read this manual carefully.
2. Follow all instructions and warnings.
3. Only use accessories specified by WORK PRO.
4. Follow the safety instructions of your country.
5. Be careful with sound levels.
SYMBOLS
The following symbols are used in this document:
This symbol indicates a potential risk of harm to a person or damage to the
product. You can also notify the user of the instructions that must be followed
strictly to ensure the installation or safe operation of the product.
This symbol notifies the user about the instructions that must be followed strictly
to ensure the correct installation or operation of the product.
This symbol notifies the user about additional information or optional
instructions.
WELCOME TO WORK PRO
Thank you for choosing the WORK PRO WPE 24 system.
This document contains essential information on the use of the system. Read this
document carefully to become familiar with the system.
Please check the WORK PRO website regularly to download the latest version of the
document and software updates: https://www.workpro.es/

WPE 24
USER MANUAL
VERSION 1.1
WPE SERIES www.workpro.es 2
CONTENT
1. INTRODUCTION.................................................................................................................................3
2. FEATURES..........................................................................................................................................3
3. PRODUCT DESCRIPTION....................................................................................................................4
Analog audio input.....................................................................................................................7
Analog audio output ..................................................................................................................7
LAN Port.....................................................................................................................................8
3.3.1. Main supply input........................................................................................................ 8
4. DEVICE SETUP ...................................................................................................................................8
4.1.1. Setup through WorkCAD3 Configurator ..................................................................... 8
5. OSC COMMANDS ............................................................................................................................13
6. ACCESSORIES...................................................................................................................................18

WPE 24
USER MANUAL
VERSION 1.1
WPE SERIES www.workpro.es 3
1. INTRODUCTION
WPE 24 is a digital signal processor with external control capability. Its compact
design and format make it perfect for use by audiovisual integrators.
The device has balanced inputs and outputs to give them greater immunity
against electromagnetic interference.
The external control of this device is done thanks to its Ethernet connectivity,
which can be done through the dedicated WorkCAD3 software or through OSC
commands by third-party devices.
2. FEATURES
Audio analog inputs
Number of inputs
2 balanced inputs
Audio connector
Euroblock, 3 pin 3.81mm
Input sensitivity
14 dBu (balanced) (3.88 Vrms )
Audio process per-input
4 filters
Gain control
Mute and Invert control
Audio analog outputs
Number of outputs
4 servo-balanced outputs
Audio connector
Euroblock, 3 pin 3.81mm
Input sensitivity
+10 dBu (balanceado) (2.45 Vrms)
Audio process per-output
15 filters
2 crossover filters (High pass, Low Pass)
Weighted matrix of sum of inputs
Delay up to 8.19 ms
Compressor/Limiter/Noise gate
General
SNR
> 100 dB
THD + N
< 0.01 %
Bandwidth
20 Hz –24000 Hz
Sampling frequency
48000 Hz
Input/output filter types
Low pass, High pass, Low Shelving, High
Shelving, Band pass, Peak, Notch y All
pass.
Number of memories
8
Dimensions
109mm×133.75mm×40.45 mm
Weight
360 g

WPE 24
USER MANUAL
VERSION 1.1
WPE SERIES www.workpro.es 4
Network
Connector
RJ-45
Control Protocol
OSC over UDP y RUDP
Ports
UDP 9000 / RUDP 9002
Ethernet
100 base TX
Main Supply
External main supply
24 Vdc / 500 mA (Not incluided)
PoE Class
Class 0 802.3af
Consumption
3.6 W
3. PRODUCT DESCRIPTION
1. Reset button. Restore the device to its factory configuration
2. Next button. It allows to advance between and through the different
screens of the display.
3. Display. It shows different features of the device.
4. Set button. It allows access to a certain display screen and set the digits of
the different screens.
5. LAN port. Connection port to the local network, RJ45.
6. Main supply input. 12/24 Vdc
7. Analog audio input. Balanced inputs. Euroblock 3 pins, 3.81 mm per input.
WPE 24 (2 INPUTS)
8. Analog audio output. Balanced outputs. Euroblock 3 pins, 3.81 mm per
output.
WPE 24 (4 OUTPUTS).

WPE 24
USER MANUAL
VERSION 1.1
WPE SERIES www.workpro.es 5
Display
On the front panel you will find a display where you can view different
parameters of the unit.
To navigate between the different parameters press the NEXT button. If you want
to edit any of these parameters, press the SET button to access it. Next, specify
which parameters are editable and which are not:
LEVELS, not editable
STATIC IP, editable
DYNAMIC IP, not editable
MAC, not editable
ACTIVE PRESET, editable.
LEVELS, It shows the signal level present in the inputs and outputs. It is the default
screen of the device and to which it returns after 10 seconds without editing a
screen. Next to each input/output there is a bar which indicates the level
according to the attached chart:
Bar amplitude
(from 0 to 8)
Level (dBFS)
8
-3 dBFs / 0 dBFs
7
-6 dBFs / -3 dBFs
6
-9 dBFs / -6 dBFs
5
-18 dBFs / -9 dBFs
4
-26 dBFs / -18 dBFs
3
-40 dBFs / -26 dBFs
2
-60 dBFs / -40 dBFs
1
-80 dBFs / -60 dBFs
None
< 80 dBFs

WPE 24
USER MANUAL
VERSION 1.1
WPE SERIES www.workpro.es 6
STATIC IP, this is the static IP address. The device has a static IP address by default
in the subnet 10.0.0.0/8. For editing, use the buttons SET (to select and set the
digit) and NEXT (for editing upwards).
NOTE: ENABLED by default
NOTE: After a change, the device restarts to confirm the value.
DYNAMIC IP, this is the dynamic IP address of the device, which is assigned by
a DHCP server.
NOTE: DISABLED by default. Only displayed when selecting this mode by software.
MAC. this is the physical address of the device.
ACTIVE Preset. Allows you to select one of the 8 presets available for
activation

WPE 24
USER MANUAL
VERSION 1.1
WPE SERIES www.workpro.es 7
Analog audio input
The connection of the input signal to the device can be balanced or
unbalanced. Keep in mind that balanced signals provide 6 dB more level than
unbalanced signals of equal amplitude.
UNBALANCED
BALANCED
Analog audio output
The analog audio output of the device can be balanced or unbalanced
according to the selected extraction mode. To do this, keep in mind the following
types of connection:
UNBALANCED

WPE 24
USER MANUAL
VERSION 1.1
WPE SERIES www.workpro.es 8
BALANCED
LAN Port
RJ45 port for LAN connection. Allows PoE power (Class 0 802.3af)
Next to the RJ45 connector you will find two LEDs indicating the status of the
device:
LINK (green)
Indicates that the WPE 24 is connected to the LAN
ACT
(orange)
Indicates that packets are being sent or received
3.3.1. Main supply input
Power input for external source. The admitted voltage can be between 12/24
Vdc, with a minimum current of 500 mA.
Check the current polarity before connecting the main supply
The external power supply is not provided with the device.
4. DEVICE SETUP
The configuration of the device can be done by software (WorkCAD3
configurator) or through display. The most comfortable way for the user is through
WorkCAD3 configurator, since it will have access to all the functionalities of the
device and you can also see the interaction of your device with the rest of the
BlueLine Digital MKII network elements.
4.1.1. Setup through WorkCAD3 Configurator
After making the configuration at the IP level of the device and updating it if
necessary (see WorkCAD3 Configurator user manual), proceed with its
configuration.

WPE 24
USER MANUAL
VERSION 1.1
WPE SERIES www.workpro.es 9
If you click with the left mouse button on the device, the configuration interface
will open where the following parameters appear:
-VIEW
•DSP. It allows to choose the visualization of the processing fields.
•Setup. It allows to go to the selection menu of the starting mode of
the device..
-PRESETS
•Preset selection. It allows to choose the preset with which you want
to work..
•LOAD. It allows you to load the previously selected preset.
•STORE. It allows saving over the previously selected preset
•RENAME. It allows you to rename the previously selected preset.
-MASTER: It allows the modification both graphically and numerically of
the general volume control of the device. In addition, it has a MUTE
button.
-DSP: It is the area where the processing of the inputs and outputs of the
device is configured.
•Input and output selection field. It allows to choose the I/O on
which you want to work. The parameters to control will vary
depending on whether an Input or Output has been chosen
•Gain. Field that allows to control the volume or invert the polarity
of the selected I/O.