World Video Sales MicroImage Video Systems VDA106 User manual

Page 4
WARRANTY
MicroImage Video Systems warrants that each VDA106 is free from
defects due to faulty materials or improper workmanship for a period of
one (1 year. MicroImage Video Systems further warrants that any part
which proves defective in materials or workmanship within one (1 year,
will be replaced or repaired at no cost to the user. Labor to replace
defective parts will be done without charge, provided the equipment is
returned to MicroImage Video Systems prepaid, insured and properly
packaged. Prior return authorization must be obtained from MicroImage
Video Systems.
NOTE
This warranty covers the MicroImage VDA106 only.
CONDITIONS
This warranty is void if the warranted part has been altered or subjected
to abuse or misuse. Defective parts must be returned to MicroImage
Video Systems.
SOLE WARRANTY
This Warranty is in lieu of all other warranties expressed or implied
including, without limitation, any implied warranty or any implied
warranty of fitness for a particular purpose. MicroImage Video Systems
shall have the final right to determination as to the existence and cause of
any defect and its appropriate adjustment in accordance with the terms of
this warranty. In no event shall MicroImage Video Systems be liable for
any consequential or collateral damages.
RETURNS
All returns MUST have an RMA number. Please call, fax or email
for an RMA form. The RMA form will have the proper shipping
address for returns.
Phone [phone]
Fax [phone]
Email [e-mail]
Video 1x6
DISTRIBUTION AMPLIFIER
Operation Manual
Model VDA106
MicroImage Video Systems
division of World Video Sales Co., Inc
PO Box 331
Boyertown, PA 19512
Phone [phone]
Fax [phone]
[e-mail]
www.mivs.com

Page 2
CONTENTS
SPECIFICATIONS....................................................................2
UNPACKING.............................................................................3
CONNECTIONS........................................................................3
Power ....................................................................................3
Video.....................................................................................3
IN CASE OF DIFFICULTY........................................................3
WARRANTY..............................................................................4
RETURNS.................................................................................4
Rev 0 09-30-1998, Reviewed 07-07-2015
SPECIFICATIONS
Input level 1.0 Vpp Composite, 75 Ω
Output level Same as respective inputs "2% into 75 Ω
Connectors VDA106 BNC female
Bandwidth Greater than 30Mhz
Temperature
Operating 0E - 40E C (32E - 104E F
Storage -40E - 60E C (-40E - 140E F
Humidity
Operating 10% - 90% (non-condensing
Storage 5% - 95% (non-condensing
Power
Voltage 110 - 125VAC, 50/60Hz
(+12VDC & 230VAC available, contact factory
Consumption 12W
Size 8.6" (W x 6.7" (D x 2.4" (H
218.5 mm (W x 170 mm (D x 61 mm (H
Weight 1 lb, 15 oz.
Manufactured in USA by MicroImage Video Systems
Page 3
UNPACKING
The VDA106 package includes the following items:
VDA106 Video Distribution Amplifier
CAB05006 Power Cord
This operation manual
Please inspect all items carefully and report damaged or missing
items to your dealer or MicroImage Video Systems.
CONNECTIONS
ower
The VDA106 uses an industry standard, detachable 3 wire power
cord which is included with the unit. For medical applications, a
special low leakage cord (part # CAB01006 is available. Connect
the cord to a suitable power source of 120VAC, 50-60Hz.
Video
Connect the video source (i.e. camera to the IN connector on the
VDA unit. Connect the OUTPUT signals from the VDA unit to the
video displays as required. Each output can only have a single 75
ohm termination.
The VDA106 uses BNC connectors.
IN CASE OF DIFFICULTY
If you are experiencing problems with any MicroImage product,
you can contact MicroImage Support using the following methods:
Phone [phone]
Fax [phone]
Email [e-mail]
Web www.mivs.com