World Video Sales MicroImage Video Systems VDA116RM User manual

VDA116RM
Operation Manual
Rack Mount Video 1 x 16
Distribution Amplifier
MicroImage Video Systems
division of World Video Sales Co., Inc.
P.O. Box 331
Boyertown, PA 19512
610-754-6800
Fax [phone]
[email protected]
www.mivs.com
Page 2
Contents
Specifications
Specifications ............................... Page2
Unpacking .................................. Page3
Connections ................................ Page3
Power ................................ Page3
Video ................................ Page3
Incaseofdifficulty............................ Page3
Warranty................................... Page4
Returns.................................... Page4
Rev 1 08-02-2002
Input level 1.0 Vpp Composite, 75 Ω
Output level Same as input into 75 Ω
Internally adjustable
Connectors BNC female
Bandwidth Greater than 30Mhz
Temperature
Operating 0E-40EC (32E-104EF)
Storage -40E-60EC (-40E-140EF)
Humidity
Operating 10% -90% (non-condensing)
Storage 5% -95% (non-condensing)
Power
Voltage 110 -125VAC, 50/60Hz
Consumption 25W max
Size 19" (W) x 6.7" (D) x 1.7" (H)
482.6 mm (W) x 170.2 mm (D) x 43.2 mm (H)
Weight 2.5 lb.
Manufactured in USA by MicroImage Video Systems

Page 3
Unpacking
Connections
In case of difficulty
The VDA1116RM package includes the following items:
VDA116RM Video Distribution Amplifier
CAB05006 Power Cord
75 ohm 1% Termination
This operation manual
Please inspect all items carefully and report damaged or missing
items to your dealer or MicroImage Video Systems.
Power
The VDA116RM uses an industry standard, detachable 3 wire
power cord which is included with the unit. For medical
applications, a special low leakage cord (MicroImage part #
CAB01006) is available. Connect the cord to a suitable power
source of 120VAC, 50-60Hz.
Video
Connect the video source (i.e. camera) to the IN connector on the
VDA unit. Connect the OUTPUT signals from the VDA unit to the
video displays or other equipment as required. Each output must
only have a single 75 ohm termination.
The VDA116RM uses female BNC connectors.
If you are experiencing problems with your MicroImage product,
you can contact us in one of the following ways.
Mail MicroImage Video Systems
a division of World Video Sales Company, Inc.
P.O. Box 331
Boyertown, PA 19512
Phone [phone]
Fax [phone]
Email [email protected]
Web www.mivs.com
Page 4
Warranty
Returns
MicroImage Video Systems warrants that each VDA116RM is free from
defects due to faulty materials or improper workmanship for a period of
one (1) year. MicroImage Video Systems further warrants that any part
which proves defective in materials or workmanship within one (1) year,
will be replaced or repaired at no cost to the user. Labor to replace
defective parts will be done without charge, provided the equipment is
returned to MicroImage Video Systems prepaid, insured and properly
packaged. Prior return authorization must be obtained from MicroImage
Video Systems.
NOTE
This warranty covers the MicroImage VDA116RM Video Distribution
Amplifiers only.
CONDITIONS
This warranty is void if the warranted part has been altered or subjected
to abuse or misuse. Defective parts must be returned to MicroImage
Video Systems.
SOLE WARRANTY
This Warranty is in lieu of all other warranties expressed or implied
including, without limitation, any implied warranty or any implied
warranty of fitness for a particular purpose. MicroImage Video Systems
shall have the final right to determination as to the existence and cause
of any defect and its appropriate adjustment in accordance with the terms
of this warranty. In no event shall MicroImage Video Systems be liable for
any consequential or collateral damages.
All returns MUST have an RMA number. Please call, fax or email for
an RMA form. The RMA form will have the proper shipping address
for returns.
Phone [phone]
Fax [phone]
Email [email protected]