World Video Sales MicroImage Video Systems VDA206 User manual

VDA206
Operation Manual
S-Video 1 x 6
Distribution Amplifier
MicroImage Video Systems
division of World Video Sales Co., Inc.
P.O. Box 331
Boyertown, PA 19512
610-754-6800
Fax [phone]
[email protected]
www.mivs.com
Page 2
Contents
Specifications
Specifications ...............................Page 2
Unpacking ..................................Page 3
Connections ................................Page 3
Power ................................Page 3
Video ................................Page 3
In case of difficulty ...........................Page 3
Warranty ..................................Page 4
Returns ....................................Page 4
Rev 0 09-30-1998
Input level 1.0 Vpp Composite, 75 Ù
Output level Same as respective inputs ±2% into 75 Ù
Connectors
VDA206 4 pin mini-DIN female (std. S-Video conn.)
Bandwidth Greater than 30Mhz
Temperature
Operating 0E-40EC (32E-104EF)
Storage -40E-60EC (-40E-140EF)
HumidityOperating 10% -90% (non-condensing)
Storage 5% -95% (non-condensing)
Power Voltage 110 -125VAC, 50/60Hz
(+12VDC & 230VAC available, contact factory)
Consumption 12W
Size 8.6" (W) x 6.7" (D) x 2.4" (H)
218.5 mm (W) x 170 mm (D) x 61 mm (H)
Weight 1 lb, 15 oz.
Manufactured in USA by MicroImage Video Systems

Page 3
Unpacking
Connections
In case of difficulty
The VDA206 package includes the following items:
VDA206 Video Distribution Amplifier
CAB05006 Power Cord
This operation manual
Please inspect all items carefully and report damaged or missing
items to your dealer or MicroImage Video Systems.
Power
The VDA206 uses an industry standard, detachable 3 wire power
cord which is included with the unit. For medical applications, a
special low leakage cord (part # CAB01006) is available. Connect
the cord to a suitable power source of 120VAC, 50-60Hz.
Video
Connect the video source (i.e. camera) to the IN connector on the
VDA unit. Connect the OUTPUT signals from the VDA unit to the
video displays as required. Each output can only have a single 75
ohm termination.
The VDA206 uses industry standard mini-DIN connectors for S-
Video.
If you are experiencing problems with your MicroImage product,
you can contact us in one of the following ways.
Mail MicroImage Video Systems
a division of World Video Sales Company, Inc.
P.O. Box 331
Boyertown, PA 19512
Phone [phone]
Fax [phone]
Email [email protected]
Web www.mivs.com
Page 4
Warranty
Returns
MicroImage Video Systems warrants that each VDA206 is free from
defects due to faulty materials or improper workmanship for a period of
one (1) year. MicroImage Video Systems further warrants that any part
which proves defective in materials or workmanship within one (1) year,
will be replaced or repaired at no cost to the user. Labor to replace
defective parts will be done without charge, provided the equipment is
returned to MicroImage Video Systems prepaid, insured and properly
packaged. Prior return authorization must be obtained from MicroImage
Video Systems.
NOTE
This warranty covers the MicroImage VDA206 Video Distribution
Amplifiers only.
CONDITIONS
This warranty is void if the warranted part has been altered or subjected
to abuse or misuse. Defective parts must be returned to MicroImage
Video Systems.
SOLE WARRANTY
This Warranty is in lieu of all other warranties expressed or implied
including, without limitation, any implied warranty or any implied
warranty of fitness for a particular purpose. MicroImage Video Systems
shall have the final right to determination as to the existence and cause
of any defect and its appropriate adjustment in accordance with the
terms of this warranty. In no event shall MicroImage Video Systems be
liable for any consequential or collateral damages.
All returns MUST have an RMA number. Please call, fax or email
for an RMA form. The RMA form will have the proper shipping
address for returns.
Phone [phone]
Fax [phone]
Email [email protected]