Worth Data 530-2D-USB User manual

Owner’s Manual
Worth Data®
USB 2D Bar Code
Scanner - Scan 1D &
2D Matrix Bar codes
530-2D-USB 2D Scanner
www.worthdata.com
High Speed Imaging USB Bar Code Scanner

Warning: This equipment generates, uses and can radiate radio frequency energy. If not
installed and used in accordance with the instruction manual, it may cause interference to radio
communications. It has been tested and found to comply with the limits for a Class Acomputing
device pursuant to Subpart J of part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial environment. Operation of
this equipment in a residential area is likely to cause interference in which case the user at his
own expense will be required to take whatever measures may be required to correct the
interference.
This manual contains confidential and proprietary information and is copyrighted.All rights
reserved. No part of this manual may be photocopied or reproduced in any form without the
prior written consent of Worth Data® Inc.
WARNING:This product can expose you to chemicals including lead, phthalate or bisphenol A which are
known to the state of California to cause cancer, birth defects or other reproductive harm. For more information
go to www.P65Warnings.ca.gov
Worth Data, Inc.
USA Headquarters
623 Swift Street
Santa Cruz, CA 95060
USA
Phone: [phone] • 831-458-9938
Fax: [phone]
Email: [email protected]om
www.worthdata.com

Contents
Introduction _______________________________________________________________________ 1
Installation ________________________________________________________________________ 2
Configuration______________________________________________________________________ 3
Setup Codes _______________________________________________________________________ 4
Beeper and LED Settings: __________________________________________________________ 6
Trigger and Scan Mode Settings:_____________________________________________________ 8
Picklist Mode____________________________________________________________________ 9
Continuous Read Mode ____________________________________________________________ 9
Unique Bar Code Reporting_________________________________________________________ 9
Decode Timeout__________________________________________________________________ 9
Mobile Phone/Display Mode_______________________________________________________ 10
Low Light Assist ________________________________________________________________ 11
Prefix & Suffix Parameters:________________________________________________________ 12
USB Interface Settings: ___________________________________________________________ 15
Bar Code Setup:_________________________________________________________________ 17
1D Bar Code Setup Options__________________________________________________________ 18
UPC/EAN/JAN Code Options: _____________________________________________________ 18
Code 128 Options: _______________________________________________________________ 29
Code 39 Options: ________________________________________________________________ 34
Code 93 Options: ________________________________________________________________ 39
Code 11 Options: ________________________________________________________________ 40
Interleaved 2 of 5 (ITF) Options:____________________________________________________ 42
Discrete 2 of 5 (DTF) Options: _____________________________________________________ 45
Codabar (NW – 7) Options:________________________________________________________ 47
MSI Options: ___________________________________________________________________ 49
Matrix 2 of 5 Options: ____________________________________________________________ 51
Inverse 1D Options:______________________________________________________________ 53
GS1 DataBar Options: ____________________________________________________________ 54
Symbology-Specific Security Features:_______________________________________________ 57
Security Level:__________________________________________________________________ 58
1D Quiet Zone Level: ____________________________________________________________ 59
Intercharacter Gap Size:___________________________________________________________ 59
Composite Bar Code Options ______________________________________________________ 60
2D Symbologies___________________________________________________________________ 63
PDF417 Options_________________________________________________________________ 63

Data Matrix Options: _____________________________________________________________ 64
Maxicode Options:_______________________________________________________________ 65
QR Code options:________________________________________________________________ 65
MicroQR Options: _______________________________________________________________ 65
Aztec Options: __________________________________________________________________ 66
Postal Codes______________________________________________________________________ 67
US Postal Code Options: __________________________________________________________ 67
UK Postal Code Options:__________________________________________________________ 68
Japan Postal Code Options: ________________________________________________________ 68
Netherlands KIX Code Options: ____________________________________________________ 68
Australia Post Code Options:_______________________________________________________ 69
Resolving USB Installation Issues in Windows___________________________________________ 70
Resolving USB Installation Issues in macOS ____________________________________________ 72
Appendix A: Numeric Bar Codes _____________________________________________________ 73
Appendix B: Alphanumeric Bar Codes _________________________________________________ 74
Appendix C: Character Sets__________________________________________________________ 82
Appendix D: Code Identifiers ________________________________________________________ 88

1
Introduction
Worth Data's 530-2D-USB is a versatile bar code reader that can attach to any PC, Mac or Linux USB
port as a HID USB Keyboard. The USB keyboard interface provides bar code input data to any host
computer program exactly as if the data had been typed at the keyboard, including function and control
key support. 530-2D reader features include:
• Bar codes
The 530-2D automatically reads and discriminates between Code 39, Full ASCII Code 39, Interleaved
2 of 5, Industrial 2 of 5, Matrix 2 of 5, Codabar, Code 128, EAN-13, EAN-8, UPC (with or without
supplements), GS1 DataBar, POSTNET, Intelligent Mail Bar Code, IATA, PDF417, Micro PDF417,
Maxi Code, QR Code, Micro QR, Aztec Code, Data Matrix, and several more 1D and 2D bar code
symbologies.
• PC Attachment
The 530-2D provides an easy-to-use USB keyboard interface for the PC or Mac. Scanned data is
displayed on the PC as keyboard data - transparent to the host application. No additional software is
required for operation or configuration.
• Configuration is easy
The 530-2D reader is easily configured for your system by scanning a bar coded Setup Menu. In most
cases, the 530-2D will do what you need without any changes to its configuration.

2
Installation
Components of 530-2D Reader
In the event the shipping box shows damage on arrival, please note the damage on the carrier's receipt log. Open
the box and inspect the contents for damage. If there is visible damage, or if the unit fails to work, contact us
with the details of the trouble; we will be happy to send you a replacement.
The contents of your 530-2D reader shipment should include the following:
1. A 530-2D-USB bar code scanning gun with C45 USB cable attached.
2. A scanner holder.
3. A Quick Start Guide
4. A Utilities CD-ROM with Manuals PDF Format.
USB Interface (PC and Mac)
The 530-2D reader is attached directly to the USB port of the computer running Windows®, macOS, Mac OS X,
or Linux. The Windows, Macintosh®, or Linux operating system provides the software driver required to access
the USB port. Data coming from the scanner through the USB port appears as keyboard data in your application.
No power supply is required for the USB interface.
Simply plug the USB cable into any available USB port on your PC, or powered HUB, and the 530-2D
should power-up and be ready to use in a few seconds. It is not recommended to use non-powered hubs
due to the high power requirements of the 530-2D.

3
Configuration
Configuration of the 530-2D Reader
The 530-2D is configured using the setup bar codes below. Most commands are of the single entry type and
only require a single command to enable or disable a feature or function. It may be necessary to enable
parameter scanning if parameter scanning has been disabled. Parameter scanning is enabled by default.
Parameter scanning can also be locked with a security code if desired. These options will be covered in the User
Preferences chapter.
When scanning setup bar codes (or just about any bar code for that matter) follow these tips for best results:
1) Since the 530-2D functions like a camera, holding the scanner steady will improve scanning results.
2) When more than one bar code is in the visible area of the scanner it is a good idea to cover the
“unwanted” bar codes to prevent them from being read by accident.
3) If you scan a setup code by accident and the scanner is not working properly but you're not sure what
you changed, it's best to scan the “Reset All Settings to Default” bar code and start over.
4) You will find that most bar codes read better when the scanner is angled slightly so that the light
reflected from the bar code does not “blind” the scanner. It's just like if you were to try to take a flash
picture of a piece of paper, when you do it straight on the flash bounces back and you get a lot of glare
but if you do it at a slight angle you get a nice picture.
5) Reading of high-resolution bar codes may require you to move the scanner closer to the bar code to get a
good read. The optimum reading distance is 7” from the front of the gun to the bar code.
6) When reading poor quality bar codes, it is a good idea to put tighter limits on what the bar code reader
will allow to prevent errors in reading.
7) The 530-2D is an “Omnidirectional” bar code reader so bar codes can be read with any orientation or
rotation relative to the reader.
8) There is a special aiming assist dot in the beam as shown below to help you target the correct barcode.

4
Setup Codes
Set to Factory Default:
To set the scanner to factory defaults, scan the code below. Factory defaults are indicated by an
asterisk (*) throughout the manual.
Set USB HID-Keyboard I/F and ResetAll Settings to Default
Warning: These setup codes in this manual are for the 530-2D-USB only. Do not use these codes
to try to change the setup on the 510-2D, 520-2D-USB, 520-RF scanners or on for the 2D
integrated 7000 Terminals or 5000 TriCoders.

5
Enable/Disable Parameter Scanning:
Parameter scanning (the scanning of setup bar codes) can be enabled or disabled by scanning one of the
codes below:
Lock/Unlock Parameter Scanning:
This feature locks parameter settings with a 4-digit code to prevent changing parameter values by
scanning parameter bar codes. This provides an added level of security not offered by Disable
Parameter Scanningabove. After scanning Lock below, the only parameter bar code that is accepted
is Unlock with the correct 4-digit code.
To lock parameter scanning:
1. Scan the Lock bar code below.
2. Scan 4 bar codes from Appendix A - Numeric Bar Codes that represent the desired code.
Enter leading zeros for numbers below 1000. For example, to program a code of 29 scan
0, 0, 2, 9. A “lock” beep will sound (2 long high pitch beeps) followed by the parameter
entry beep.
To unlock parameter scanning:
1. Scan the Unlock bar code below.
2. Scan 4 bar codes from Appendix A - Numeric Bar Codes that represent the correct code.
An “unlock” beep will sound (2 long low beeps) followed by the parameter entry beep.

6
Beeper and LED Settings:
Decode Beep
The good decode beep can be enabled/disabled using these parameter bar codes.
Note: parameter scanning beeps and error beeps cannot be disabled.
Beep Tone
The good decode beep tone can be set using these parameter bar codes.
Beep Tone Duration
The good decode beep duration can be set using these parameter bar codes.

7
Power Up Beeps
The power up beeps can be enabled/disabled using these parameter bar codes.
Good Read Decode LED
The good decode LED can be enabled/disabled using these parameter bar codes.
Illumination Good Read LED
The illumination LED can be used to indicate a good decode (direct decode indicator) using these
parameter bar codes. Note: if you release the trigger too quickly you may not see all of the blinks since
the scanner will enter sleep mode once the trigger is released.

8
Trigger and Scan Mode Settings:
Scan one of the following parameter bar codes to select a trigger mode for the gun.
•Standard – A trigger press activates the gun and starts a decode process. Decode processing
continues until the bar code decodes, the trigger is released or the decode process times out.
•Presentation (Blink) – The scanner will activate decode processing when it detects a bar code
in its field of view. After a period of non-use the illumination will turn off until the scanner
senses motion.
•Auto Aim – The scanner projects an aiming pattern when it senses motion. A trigger press
activates decode processing. After 2 seconds of inactivity the aiming pattern turns off.
•AutoAim with Illumination – The scanner turns on the aiming pattern and illumination LEDs
when it senses motion. A trigger press activates decode processing. After 2 seconds of
inactivity the aiming pattern and illumination LEDs turn off.

9
Picklist Mode
Picklist Mode can be enabled/disabled using these parameter bar codes. Picklist Mode allows the
scanning of bar codes that are close together. Only the bar code with the aiming dot on it will be
decoded. You cannot disable the aiming dot when Picklist Mode is enabled. When Picklist Mode is
enabled decode performance may be reduced and it may be more difficult to scan longer bar codes. It
is recommended to only enable Picklist Mode if needed.
Continuous Read Mode
Continuous Read Mode can be enabled/disabled using these parameter bar codes. Continuous Read
Mode decodes all bar codes in the field of view when the trigger is pressed. Continuous Read Mode
works well with Picklist Mode above. Continuous Read Mode by itself can cause accidental decodes if
more than one bar code is in view.
Unique Bar Code Reporting
Unique Bar Code Reporting can be enabled/disabled using these parameter bar codes. This option
only works when Continuous Bar Code Read is enabled above. Unique Bar Code Reporting forces the
scanner to output only unique bar codes when the trigger is pressed.
Decode Timeout
Timeout Between Decodes, Same Symbol can be set using this parameter bar code. Use this setting
along with Presentation Mode or Continuous Bar Code Read to prevent the scanner from continuously
decoding the same symbol when it is left in the scanner’s field of view. The decoded bar code must be
out of the scanner’s field of view for this amount of time before it can be decoded again. The value is
programmable in 0.1 second increments with a range of 0.0 seconds to 9.9 seconds. The default value
is 0.6 seconds. To set the timeout between decodes for the same symbol, first read the bar code below
then scan 2 digits from Appendix A – Numeric Bar Codes that correspond to the desired interval.

10
Timeout Between Decodes, Different Symbol can be set using this parameter bar code. Use this
setting along with Presentation Mode or Continuous Bar Code Read to set the delay between reading
different bar codes. The value is programmable in 0.1 second increments with a range of 0.1 to 9.9
seconds. The default value is 0.1 seconds. To set the timeout between decodes for the same symbol,
first read the bar code below then scan 2 digits from Appendix A – Numeric Bar Codes that correspond
to the desired interval. Note: the timeout must be less than the Decode Session Timeout.
Decode Session Timeout can be set using this parameter bar code. This parameter sets the maximum
time that the scanner will attempt to decode a bar code. The value is programmable in 0.1 second
increments with a range of 0.5 to 9.9 seconds. The default value is 9.9 seconds. To set the decode
timeout, first read the bar code below then scan 2 digits from Appendix A – Numeric Bar Codes that
correspond to the desired timeout.
Mobile Phone/Display Mode
Mobile Phone/Display Mode can be enabled/disabled using these parameter bar codes. This mode
improves scanning performance on mobile phone and other displays.

11
Low Light Assist
Low LightAssist Detection can be adjusted using these parameter bar codes. The illumination and
aiming pattern can be disabled or dimmed for use in dim or dark environments.
•No Low Light Scene Detection – The scanner attempts to detect motion as best it can with
the aim pattern and illumination turned off when the scanner is idle.
•Aiming Pattern Low LightAssist Scene Detection – Illumination is off, but the aiming
pattern is on when the engine is idle to assist with detection.
•Dim Illumination Low Light Assist Scene Detection – The aiming pattern is off, but
illumination is on at a dim level to assist with detection.

12
Prefix & Suffix Parameters:
The Prefix and Suffix parameters are used to add a prefix and/or suffix to the data output by the
scanner.
Terminator Character – Common Suffix
The most common suffix, or Terminator Character, is the Enter Key (carriage return/line feed). Scan
this bar code to set the Terminator Character suffix to Enter Key (enabled by default):
Another popular suffix is the Tab Key. Scan this bar code to set the Terminator Character suffix to a
Tab Key:
To clear the suffix and transmit all DataAs-Is without any Terminator Characters or suffix characters,
scan this bar code:
Code ID Character
A common prefix is the Code ID Character this can be enabled/disabled using the bar codes below.
The code ID character is output in addition to any prefix that is already set. The code ID is inserted
between the prefix (if set) and the bar code data. A table of code ID characters can be found in
Appendix D.

13
Prefix & Suffix
Prefix & Suffix values can be set using the bar codes below. You can append a prefix and/or one or
two suffixes to scan data output. The Enter Key terminator option above does not count as one of the
two suffixes. If Enter Key is enabled above it will be appended after any suffix character(s).
To set a value for a prefix or suffix, scan one of the following bar codes, and then scan four bar codes
from Appendix A - Numeric Bar Codes that correspond to the desired value. See Appendix C -
Character Sets for the 4 digit codes.
To correct an error or change a selection, scan the Data Format Cancel bar code.

14
Prefix & Suffix Transmission Format
The Scan Data Transmission Format can be set using the bar codes below. One of the options must
be selected to enable a prefix or suffix entered above. The default is transmit data as is without prefix
or suffix.

15
USB Interface Settings:
USB Keystroke Delay
Scan one of the following bar codes to add a delay between keystroke data output by the scanner.
Slower host computers may require a delay.
Caps Lock Override
USB Caps Lock Override – Enable Override Caps Lock Key to preserve the case of the data
regardless of the state of the Caps Lock key.
Bar Codes with Unknown Characters
Unknown characters are characters the host does not recognize.
Scan Send Barcodes with Unknown Characters to send all barcode data except for unknown
characters. No error beeps are given when scanning a barcode with unknown characters.
Scan Do Not Send Barcodes with Unknown Characters to send all barcode characters up to the
unknown character. The scanner will give an error beep.