Worth Data LZ360-RF User manual

CLEAR Clears Preamble
and Postamble.
Resets scanned
parameter back to
default sett ngs.
Preamble Scan up to 15 characters
from the Full ASCII
Menu. Scan SET when
f n shed
Beep Options * 0) Decode + Ack.
1) Ack Only
RESET
WARNING! Scann ng RESET after scann ng START
SETUP resets the reader back to DEFAULT sett ngs,
el m nat ng any setup changes for all parameters.
MSI/Plessey * 0) D sable
1) Enable 1 Mod 10
2) Enable 2 Mod 10
3) Enable Mod 11/Mod 10
* 4) Transm t no check d g t 5) Transm t 1 check d g t
6) Transm t 2 check d g ts 7)Enable Plessey bar code
Code 128 0) D sable Code 128
* 1) Enable Code 128
2) D sable UCC/EAN 128
* 3) Enable UCC/EAN 128
Codabar 0) Enable Codabar
* 1) D sable Codabar
2) Enable CLSI Codabar
* 3) D sable CLSI Codabar
* 4) Suppress Start/Stop
5) Enable Start Stop
UPC and EAN
* 0) Enable UPC/EAN
1) D sable UPC/EAN
2) Enable Supplements
* 3) D sable Supplements
* 4) Transm t UPC-A NSC
5) Don’t Transm t UPC-A NSC
* 6) Transm t UPC-A Check D g t
7) Don’t Transm t UPC-A Check D g t
8) Transm t UPC-E NSC and EAN-8 Flag Ch
* 9) Don’t Transm t UPC-E NSC or EAN-8 Flag Ch
A) Transm t UPC-E/EAN-8 Check D g t
* B) Don’t Transm t UPC-E/EAN-8 Check D g t
* C) UPC-E Compressed Transm ss on
D) UPC-E Expanded Transm ss on
* E) EAN-8 observes 9 & A above
F) EAN s forced to transm t 8 d g ts always
Code 93 0) Enable
* 1) D sable
2) Enable Full ASCII
* 3) D sable Full ASCII
2 of 5 Code 0) Enable I 2of5
* 1) D sable I 2of5
2) Enable Check D g t
* 3) D sable Chk D g t
4)Transm t Check D g t
* 5) Don’t Transm t Ck 6) Enable 2 of 5
* 7) D sable 2 of 5
Code 3 of 9
* 0) Enable Code 39
1) D sable Code 39
* 2) Enable Full ASCII
3) D sable Full ASCII
* 4) Enable Accumulate Mode
5) D sable Accumulate Mode
6) Transm t Start/Stop
* 7) Don’t Transm t Start/Stop
8) Enable Mod 43 Check Character
* 9) D sable Mod 43 Check Character
A) Transm t Mod 43 Check Character
* B) Don’t Transm t Mod 43 Check Character
C) Caps Lock ON
* D) Caps Lock OFF
Barpad Table
LZ360-RF & LZ404-RF Laser Setup Menu
Start Setup End Setup
1) scan “Start Setup” to put RF Laser into setup mode
2) scan parameter to change, (i e Code 3 of 9, Postamble )
3) scan corresponding bar codes from Barpad Table (0-9,A-F) to change settings
4) scan “End Setup” after all changes have been made
Instant Setup options in RED section do not require scanning Start Setup
*/A/* */B/*
*0*
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
*/+/* */-/*
*/C/* */D/*
*/1/*
*/5/* */S/*
*/R/*
*1*
*2*
*3*
*4*
*5*
*6*
*7*
*/2/*
*8*
*9*
*A*
*B*
*C*
*D*
*E*
*F*
*///*
*/W/*
*/./*
*/L/*
* default setting 04/12
*/$/*
2 of 5 Len th
Scan 2 d g t length
(default s 06)
Postamble Scan up to 15 characters
from the Full ASCII
Menu.Scan SET when
f n shed.
GS1-14 * 0) D sable
1) Standard 14 d g ts
2) 14 + Ident f ers
3) 14 + UCC-128 Emul.
*/%/*
SET
Aimin Dot Duration (LZ404RF ONLY)
Scan 1 d g t from the
Barpad Menu, from 0
to 9 seconds
*/K/*
Laser Status (Instant Settin )
*/$A/*
Transmit Setup (Instant Settin )
*/$C/*
Link Test Code (Instant Settin )
Test RF Transm ss on
w thout
tramsm tt ng data.
*--*
Characters
Redef nes
output for
characters
*.1.*
*/$B/* */$F/*
Pair Laser to Base (Instant Settin ) Ran e Test (Instant Settin ) Terminator Character
* 0) CR (Enter)
1) Tab
2) None
*/H/*

NUL DLE(f10) SP 0@P`p
SOH(f1) DC1(Del) !1 Qaq
STX(f2) DC2(Ins) “2 B Rbr
ETX(f3) DC3( ) #3 C S cs
EOT(f4) DC4( ) $4 D T dt
ENQ(f5) N K( ) %5 E U eu
CK(f6) SYN( ) &6 F V fv
BEL(f7) ETB(Home) ‘7 GWgw
BS C N(End) (8 H Xhx
HT EM(Shift ON) )9 I Y iy
LF SUB(Shift OFF) *: J Z jz
VT(Pg Up) Esc +; K [k{
FF(Pg Dn) FS(Ctrl ON) ,< L \ l|
CR GS(Ctrl OFF) -= M ]m}
SO(f8) RS( lt ON) .> N ^n~
SI(f9) US( lt OFF) /? O _oDEL
Full ASCII Menu
(Items in parentheses are transmitted in keyboard edge mode.)
Char (function)
*%U*
Decimal Hex
BARCODE
LEGEND:
000 00 016 10 032 20 048 30 064 40 080 50 096 60 112 70
001 01 017 11 033 21 049 31 065 41 081 51 097 61 113 71
002 02 018 12 034 22 050 32 066 42 082 52 098 62 114 72
003 03 019 13 035 23 051 33 067 43 083 53 99 63 115 73
004 04 020 14 036 24 052 34 068 44 084 54 100 64 116 74
005 05 021 15 037 25 053 35 069 45 085 55 101 65 117 75
006 06 022 16 038 26 054 36 070 46 086 56 102 66 118 76
007 07 023 17 039 27 055 37 071 47 087 57 103 67 119 77
008 08 024 18 040 28 056 38 072 48 088 58 104 68 120 78
009 09 025 19 041 29 057 39 073 49 089 59 105 69 121 79
010 0 026 1 042 2 058 3 074 4 090 5 106 6 122 7
011 0B 027 1B 043 2B 059 3B 075 4B 091 5B 107 6B 123 7B
012 0C 028 1C 044 2C 060 3C 076 4C 092 5C 108 6C 124 7C
013 0D 029 1D 045 2D 061 3D 077 4D 093 5D 109 6D 125 7D
014 0E 030 1E 046 2E 062 3E 078 4E 094 5E 110 6E 126 7E
015 0F 031 1F 047 2F 063 3F 079 4F 095 5F 111 6F 127 7F
*$ * *¯* *0* *%V* * * *%W* *+ *
*$A* *$Q* */A* *1* *A* *Q* *+A* *+Q*
*$B* *$R* */B* *2* *B* *R* *+B* *+R*
*$C* *$S* */C* *3* *C* *S* *+C* *+S*
*$D* *$T* */D* *4* *D* *T* *+D* *+T*
*$E* *$U* */E* *5* *E* *U* *+E* *+U*
*$F* *$V* */F* *6* *F* *V* *+F* *+V*
*$G* *$W* */G* *7* *G* *W* *+G* *+W*
*$H* *$X* */H* *8* *H* *X* *+H* *+X*
*$I* *$Y* */I* *9* *I* *Y* *+I* *+Y*
*$J* *$Z* */J* */Z* *J* *Z* *+J* *+Z*
*$K* *%A* */K* *%F* *K* *%K* *+K* *% *
*$L* *%B* */L* *%G* *L* *%L* *+L* *%Q*
*$M* *%C* *-* *%H* *M* *%M* *+M* *%R*
*$N* *%D* *.* *%I* *N* *%N* *+N* *%S*
*$O* *%E* */O* *%J* *O* *%O* *+O* *%T*
➝➝
➝➝
➝➝
➝➝
*%U*