WSL TyrePal TC215 User manual
PAGE 3
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
10 min 10 min
DO NOT PRESSURE WASH SENSORS
7.0M max
SENSORS GO TO SLEEP AFTER 10
MINUTES OF NO VEHICLE
MOVEMENT.
MONITOR GOES TO SLEEP AFTER
10 MINUTES OF NO VEHICLE
MOVEMENT.
SENSORS AND MONITOR WAKE UP
WHEN MOTION OR VIBRATION ARE
DETECTED.
NOTE: FOR DISTANCES GREATER
THAN 7.0M OUR TCRR-2 SMART
SIGNAL REPEATER IS REQUIRED
PAGE 4
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
READ INSTRUCTIONS BEFORE INSTALLING
THIS KIT DOES NOT REPLACE THE NEED TO CARRY
OUT REGULAR CHECKS ON THE CONDITION AND WEAR
OF THE TYRES
MONITOR SHOULD BE INSIDE VEHICLE WHERE IT
DOES NOT INTERFERE WITH DRIVING
IT IS YOUR RESPONSIBILITY TO ENSURE THIS KIT
IS SUITABLE FOR YOUR PARTICULAR VEHICLE, THAT
IT IS WORKING CORRECTLY, AND PROPERLY
MAINTAINED
CHECK THE SENSORS AND VALVE STEMS REGULARLY
FOR DAMAGE OR CORROSION
KEEP SMALL PARTS AND BATTERIES OUT OF THE
REACH OF CHILDREN. SEEK MEDICAL ASSISTANCE IF
PARTS ARE SWALLOWED
DO NOT HOLD A BATTERY WITH METAL TWEEZERS OR
PLIERS, WHICH MAY LEAD TO A SHORT CIRCUIT
CAUSING A FIRE OR EXPLOSION OF BATTERY
DO NOT ADJUST MONITOR SETTINGS WHILST DRIVING
IF THE MONITOR ALARMS PULL OVER WHEN IT IS
SAFE TO DO SO AND CHECK THE TYRES
WEIGHT OF SENSORS WITHIN TOLERANCE FOR WHEEL
BALANCING. NO NEED TO REBALANCE WHEELS AFTER
SENSOR INSTALLATION. IF VIBRATION IS FELT
WHEN DRIVING AT SPEED, AFTER FITTING SYSTEM,
THE WHEELS MUST BE REBALANCED
PAGE 5
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
MONITOR OVERVIEW
°C
°F
PSI
BAR
TEMP
HIGH
LOW HIGH
PRESSURE
FAST
LEAKAGE
MONITOR BUTTONS,
DISPLAY LAYOUT & ICONS
SENSOR LOW
BATTERY WARNING
MONITOR BATTERY LEVEL
(FULL CHARGE = 60HRS)
ANIMATES WHEN CHARGING
ON / OFF
SWITCH
SET
-
+
LINK
CODE
TYRE ICON
TRACTOR /
TOW
VEHICLE
TRAILER
PRESSURE
DISPLAY
TEMPERATURE
DISPLAY
AMBIENT LIGHT
SENSOR FOR
BACKLIGHT
RED LED
ALARM
LIGHT
ALARM WARNING TEXT
PAGE 7
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
INSTALLATION & SET-UP PROCEDURE-
EXTERNAL TCSO SENSORS
PARTS REQUIRED
BATTERY INSTALLATION -USE BATTERY TOOL TO
OPEN AND CLOSE (TIGHTEN) THE SENSOR
NOTE: SENSOR
QUANTITIES WILL
VARY DEPENDING
ON KIT ORDER
+ve
NOTES: SLIDE BATTERY INTO HOUSING
SENSOR IS PRE-FITTED WITH AN O-
RING & VALVE SEAL. SPARES ARE
INCUDED IN KIT FOR MAINTENANCE.
WHEN REPLACING THE CAP ENSURE THE
O-RING SEAL IS IN GOOD CONDITION
AND NOT PINCHED.
DO NOT REMOVE THE WHITE PLASTIC
DISC UNDER THE BATTERY TERMINALS
TCSO SENSOR
CR1632
BATTERY
LOCK NUT
RUBBER DUST
SHIELD
BATTERY
TOOL
HEX WRENCH
TC215
MONITOR
PAGE 8
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
VALVE DUST CAP REMOVAL
INSTALL DUST SHIELD & LOCK NUT
DO NOT INSTALL SENSORS YET!
MIN. VALVE
THREAD LENGTH =
9.0mm
NOTE: WHEN THE DUST
SHIELD IS FITTED
FOLD IT BACK ON
ITSELF. THIS MAKES
IT EASIER TO FIT
LOCK NUT AND SENSOR.
CHECK TYRE
PRESSURES
BEFORE SENSORS
ARE INSTALLED
NOTE: REPEAT
FOR ALL WHEELS
REQUIRING
SENSORS
NOTE: REPEAT FOR ALL
WHEELS REQUIRING
SENSORS
PAGE 9
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
PREPARE MONITOR FOR SENSOR
REGISTRATION
SCREEN WILL SHOW ‘TRACTOR +
TRAILER’ ICONS; PSI & degC.
NB. ONCE SENSORS ARE
REGISTERED TYRE ICONS WILL
ALSO SHOW WHEN FIRST TURNED
ON, BUT NO TYRE DATA SHOWN
UNTIL TRAVELLING. TURN
MONITOR ON A FEW MINS BEFORE
SETTING OFF.
BEEP
SWITCH
ON
OR
PRESS AND
HOLD
THE “CODE” BUTTON
FOR 4-5 SECS
PRESS “+” OR “-“ BUTTON TO
SELECT WHEEL TO BE
MONITORED.
“FFF FFF” WILL APPEAR ON
SCREEN. THIS MEANS NO
SENSOR IS REGISTERED TO
THIS POSITION
PAGE 10
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
INSTALL & REGISTER SENSOR
“PSST” = 1-2 SECS
SENSOR ID CODE
APPEARS ON SCREEN
AND MONITOR BEEPS
PRESS “+”OR “–“ TO SELECT
NEXT TYRE AND REPEAT
SENSOR INSTALLATION
TO FINISH PRESS AND
HOLD
“CODE” BUTTON
FOR 4-5 SECS. TYRE PRESSURES & TEMP
WILL APPEAR ON THE SCREEN. ALARMS MAY
SOUND, PRESS ANY BUTTON TO CANCEL.
PARAMETERS CAN BE ADJUSTED DURING THE
NEXT STEPS
BEEP
BEEP
NOTE: WHEN THE SENSOR IS
SCREWED ON TO THE TYRE VALVE
IT DETECTS PRESSURE AND
SENDS IT’S UNIQUE ID CODE TO
THE MONITOR. USEFUL TIP –
ATTACH A POSITION LABEL TO
THE SENSOR CAP
HOLDING THE MONITOR AWAY
(1.5M) FROM THE TYRE, TAKE
THE FIRST SENSOR AND SCREW
IT ONTO THE VALVE STEM
PAGE 11
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
FINISH SENSOR INSTALLATION
LOCK SENSOR USING HEX
WRENCH SUPPLIED IN KIT
FOLD BACK RUBBER DUST
SHIELD SO IT COVERS
THE SENSOR
CHECK THERE ARE
NO AIR LEAKS
SPRAY INSTALLED
SENSOR WITH
SOAPY WATER. NO
BUBBLES WILL
APPEAR IF
INSTALLED
CORRECTLY
INSTALLATION /
REGISTRATION COMPLETED
–NOW SET THE ALARMS.
PAGE 14
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
SET ALARMS (for each axle)
eg.IF VEHICLE’S RECOMMENDED COLD TYRE PRESSURE
IS 35psi THEN HIGH=44psi & LOW=30psi
ie. +25% & LOW -15% YOUR VEHICLE’S COLD TYRE
PRESSURE
NOTE: “TRACTOR”UNIT
ALARMS
HIGH AND LOW PRESSURE
ALARM LEVELS TO BE SET
FOR EACH AXLE OF THE
TRACTOR UNIT
NOTE: “TRAILER” UNIT
ALARMS
HIGH AND LOW PRESSURE
ALARM LEVELS APPLY TO
ALL AXLES ON THE TRAILER
PAGE 15
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
BEEP
PRESS AND HOLD “SET” BUTTON
FOR 4-5 SECS
PRESSURE UNITS BEGIN TO FLASH
QUICKLY PRESS “SET” BUTTON
TWICE (1 SEC EACH TIME)
“HIGH PRESSURE” FLASHES AND
FRONT AXLE FLASHES
BEEP - BEEP
IF YOU WANT TO ADJUST THE
FRONT AXLE HIGH PRESSURE ALARM
PRESS THE + OR –BUTTONS TO
RAISE OR LOWER IT. IF NOT KEEP
QUICKLY PRESSING THE SET
BUTTON FOR 1 SEC UNTIL THE
AXLE YOU WANT IS FLASHING.
SET HIGH PRESSURE ALARM
LEVEL 25% ABOVE VEHICLES
RECOMMENDED TYRE
PRESSURE FOR AXLE
SELECTED
NOTE: THE MONITOR WILL NOT
ALLOW THE HIGH PRESSURE ALARM
LEVEL TO BE LESS THAN THE LOW
PRESSURE ALARM LEVEL. THE
FACTORY SET LOW PRESSURE ALARM
LEVEL IS 30 PSI. IF YOU WANT
THE HIGH PRESSURE ALARM BELOW
30PSI ADJUST THE LOW PRESSURE
ALARM FIRST.
PAGE 16
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
ONCE THE FRONT AXLE HIGH
PRESSURE ALARM IS SET PRESS
THE SET BUTTON FOR 1 SEC.
“LOW PRESSURE” FLASHES AND
THE FRONT AXLE FLASHES
IF YOU WANT TO ADJUST THE
FRONT AXLE LOW PRESSURE ALARM
LEVEL PRESS THE “+”OR “–“
BUTTONS TO RAISE OR LOWER IT.
SET LOW PRESSURE
ALARM LEVEL 15%
BELOW VEHICLES
RECOMMENDED TYRE
PRESSURE FOR AXLE
SELECTED
BEEP
BEEP
FINAL OPERATION IS TO SET
UPPER TEMPERATURE ALARM
ONCE ALL OF THE ALARMS HAVE
BEEN ADJUSTED PRESS AND
HOLD
THE “SET” BUTTON FOR 4-5
SECS TO REGISTER THE ALARMS
RECOMMENDED UPPER
TEMPERATURE ALARM IS
70°C / 158°F
PAGE 17
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
PROCEDURE TO TEST SET-UP
(WHILST VEHICLE IS STATIONARY)
REPEAT FOR ALL SENSORS.
BEEP –BEEP –BEEP…
RED ALARM LIGHT FLASHES
DISPLAY WILL SHOW
0PSI AND AUDIBLE
AND VISUAL ALARM
WILL BE TRIGGERED.
TYRE ICON WILL
FLASH.
REMOVE SENSOR FROM TYRE
VALVE. MONITOR WILL
ALARM. REPLACE SENSOR TO
CANCEL ALARM. MONITOR
WILL THEN SHOW TYRE
PRESSURE READING.
PAGE 18
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
INSTALLATION & SET-UP PROCEDURE-
INTERNAL TCSI SENSORS
PARTS REQUIRED
INSTALL INTERNAL SENSOR
NOTE: THE MANUAL DESCRIBES THE INSTALLATION AND SET-UP OF THE
INTERNAL SENSORS. IF YOU HAVE A VEHICLE WITH OUR INTERNAL
SENSORS PRE-FITTED PLEASE SKIP TO STEP 3
PREPARE SENSOR AS
SHOWN
REMOVE OLD VALVE STEM
AND CLEAN VALVE STEM
HOLE AND MOUNTING
FACES
INSTALL SENSOR
THROUGH VALVE STEM
HOLE FROM INSIDE THE
RIM
ENSURE THE SENSOR
RUBBER SEAL AND VALVE
STEM ARE SEATED
SQUARE
TCSI SENSOR
TC215
MONITOR
NOTE: SENSOR
QUANTITIES WILL
VARY DEPENDING
ON KIT ORDER
PAGE 19
505-802-100-1 TC215 MANUAL
www.tyrepal.co.uk
PREPARE MONITOR
CAREFULLY INSTALL THE
WASHER AND ENSURE IT
IS SEATED CORRECTLY
ATTACH THE THREADED
COLLAR WITH HEXAGON
UPPERMOST, AS SHOWN
TORQUE THE THREADED
COLLAR TO 6.8Nm.
REFIT THE TYRE &
INFLATE
TEST THE VALVE WITH
SOAPY WATER TO ENSURE
THERE ARE NO AIR
LEAKS
NOTE: WE RECOMMEND THE ABOVE PROCEDURE IS COMPLETED
BY A PROFESSIONAL TYRE FITTER
SWITCH
ON
Table of contents
Other WSL Diagnostic Equipment manuals
