X-Stand Paragon XSFP444 Quick guide
This X-Stand™ product(s) has been tested to rigid industry standards. Safe operation and use
of this X-Stand™ product(s) is the responsibility of the user(s). Please read and follow all safe
use instructions and warnings. Failure to follow these may result in serious injury or death!
First Edition, January 2017, Published by X-Stand™ TREESTANDS, Apple Valley Minnesota.
© 2017 X-Stand™ TREESTANDS. All right reserved.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
Max. Weight Capacity (User(s) and Equipment) 300 lbs (136 kg)
XSFP444 - PARAGON
HANG-ON ANd ClimbiNG SyStem SAFe USAGe iNStRUCtiONS & WARNiNGS
WARNING!
DO NOT
Treestand Safety: It’s Up To You
X-Stand.com
WARNING!
WARNING!
WARNING!Treestand Safety: It’s Up To You
WARNING!
TREESTAND SAFETY: IT’S UP TO YOU
WARNING!
WARNING!
WARNING!DO NOT
ALWAYS USE GENUINE FACTORY AUTHORIZED X-STAND™ REPLACEMENT
PARTS. USE OF ANY REPLACEMENT PARTS OTHER THAN GENUINE X-STAND™
PARTS VOIDS YOUR WARRANTY AND MAY RESULT IN SERIOUS INJURY OR DEATH!
WARNING!ALWAYSALL
ALL
EVERY
WARNING!
WARNING!
WARNING!
WARNING!
WARNING!Fall Arrest System (FAS)
WARNING!
ALWAYS
ALWAYS
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
WARNING!
DO NOT
WARNING!DO NOT
WARNING!DO NOT
WARNING!DO NOT
WARNING!ALWAYS
WARNING!DO NOT
WARNING!
NEVER EXCEED THESE WEIGHT
LIMITATIONS!
WARNING!DO NOT
WARNING!DO NOT
WARNING!BEFORE
WARNING!REPLACE
WARNING!
WARNING!DO NOT
DO NOT
WARNING!NEVER
WARNING!DO NOT
NEVER USE A TREE BRANCH, OR ANY
PORTION OF A TREE, TO SUPPORT ANY PORTION OF YOUR WEIGHT OR AS A HAND
HOLD.
WARNING!DO NOT
WARNING!
DO NOT
WARNING!Always
WARNING!
WARNING!
WARNING!
WARNING!
WARNING!
WARNING!
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
FUll-bOdy FAll ARReSt HARNeSS USAGe iNStRUCtiONS & WARNiNGS
WARNING!
WARNING!
WARNING!
WARNING! AN ASTM compliant full-body fall arrest harness with a
lineman’s/climbing belt must be worn at all times while installing or removing
any hang-on style treestands or climbing aids (i.e., ladders, sticks, steps,
etc.). Failure to follow these instructions may result in serious injury or death!
WARNING!
WARNING!
WARNING!
WARNING!
WARNING!Fall Arrest System (FAS)
WARNING!ALWAYS
WARNING!
WARNING!
DO NOT PANIC!
WARNING!
DO NOT
WARNING!
WARNING!
This instruction manual complies with ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
ATTENTION!! WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
FUll-bOdy FAll ARReSt HARNeSS iNStRUCtiONS
WARNING!
WARNING!ASTM
STEP 1.
STEP .
STEP .
DO NOT
WARNING!
DO NOT
USE THIS FULL-BODY FALL ARREST HARNESS!
ASTM
STEP .
STEP 1 .
6
, 9
WARNING!
WARNING!NEVER
WARNING!
WARNING!
ASTM
WARNING!
This instruction manual complies with ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
6
ATTENTION!! WHEN YOUSEE A “ WARNING!” BE SURE TO HEED THEMESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
Tether
Tether
Loop
Tether
Loop
Three
Bar
Buckle
Three
Bar
Buckle
Front ViewRear View
SRD Strap
Right
Waist
Loop
Right
Leg Strap Right
Leg Strap
Left
Leg Strap
Left
Leg Strap
Left
Waist
Loop
Tether
SRD Strap
FIG 1
shoulder
strap shoulder
strap
shoulder
strap shoulder
strap
Leg Strap
waist
belt
Leg Strap
FIG 2
Slot A
Left
Leg
Strap
Right
Leg
Strap
Three Bar
Buckle
Up through Slot B
Down through Slot A
Down through Slot B
Pull tight to secure
Back over top
Slot B
FIG 4
tree
belt
Tree Belt
Side View
FIG 7
FIG 8
Climbing Belt
tree belt
tether
FIG 5
FIG 6
tree
belt
Standing
tether
Sitting/
Seating
tree
belt
tether
FIG 9
shoulder
strap shoulder
strap
shoulder
strap shoulder
strap
Leg Strap
waist
belt
Leg Strap
FIG 3
This instruction manual complies with ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
ATTENTION!! WHEN YOUSEE A “ WARNING!” BE SURE TO HEED THEMESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
To activate your product’s warranty, a registration card (found in the back of this manual)
must be completed and returned to the manufacturer within 30 days of purchase.
Be sure to keep a copy of this card for your records.
Should you have anyquestions about the assembly, installation or use of this X-Stand
product, or any other X-Stand products, please do not hesitate to call one of our customer
service representatives at 540-877-2769 and they will answer all questions you may have
about any of the complete line of X-Stand products.
STEPS TO FOLLOW IF A FALL WERE TO OCCUR:
Although no one plans to fall from their treestand, falls can and do occur without
warning. It is important to become familiar with the guidelines below and practice your
recovery plan at ground-level. Failure to read, understand, and follow these Steps may
result in serious injury or death!
WARNING! There is time to make a correct decision on what action to take if a fall
occurs while wearing a full-body fall arrest harness. It is important NOT TO PANIC!
Remain calm and implement your practiced rescue, relief and recovery plan. Failure to
follow these instructions may result in serious injury or death!
WARNING! A suspension relief device must be on your person and readily accessible
while using a full-body fall arrest harness. This device will allow you to relieve the
load on the lower extremities if suspended in a full-body fall arrest harness and help
maintain circulation in the legs and mitigate suspension trauma (blood pooling). Follow
all instructions below regarding the provided SRD (Suspension Relief Device) and NEVER
remove it from your full-body fall arrest harness. Failure to follow this warning may result
in serious injury or death!
STEP 1. After a fall, take a moment to catch your breath and stay calm; DO NOT PANIC.
STEP 2. Pull on the SRD strap located on the front right side of your full-body fall arrest
harness. (see Fig. 10)
STEP 4. If you are able to reach your ladder or climbing system, use it to get back into
your secured treestand and then carefully climb down to ground-level. If you are not able
to reach your stand, remain calm and continue to stand in the SRD loop until help arrives.
(see Fig. 13)
STEP 3 . Adjust the SRD strap so that you are able to step into the loop and then stand up
relieving the pressure on your lower extremities. The loop size can be adjusted by moving
the buckle up or down. (see Fig. 11 & 12)
STEP 5. Use your personal locating device or cell phone to call for help.
NOTE: Several optional commercial products/systems are available that offer self-
recovery or self extraction from a fall when suspended in a full-body fall arrest harness.
Some systems automatically descend the user while others allow user control.
One of these products/systems can be considered for use as an additional safety
precaution against prolonged suspension and suspension trauma. Be sure to follow the
manufacturers’ directions on the safe use of these products/systems.
FIG 10
FIG 11
FIG 12 FIG 13
7
This instruction manual complies with ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.
[A]1/4"×1 1/4"Hex Bolt {5 Pieces} [B]5/16"×1 1/2"Hex Bolt {6 Pieces} [C]5/16"×2"Hex Bolt {2 Pieces}
1/4"Nylock Nut 5/16"Nylock Nut {8 Pieces}{5 Pieces} NylonWasher {26 Pieces}
Ratchet Strap (Loops At Both Side)
Backrest
PARAGON - PARTS LIST
Part # Description Qty Part # Description
XP15-0205 Foot Platform 1
XP15-0207 Plastic Coated Cable 2
XP15-0211 Rear Frame Support 1
XP15-0213 Bark Biter 1
XP15-0215 Seat Assembly 1
XP15-0216 Seat Bar 1
XATA620 Backrest 1
XP15-0221 Ratchet Strap 2
XP15-0020 Safety DVD 1
XP15-0200 Instruction Manual 1
XP15-0009 Full-Body Fall Arrest Harness 1
XP87-0005 1/4” x 1 1/4” Hex Bolt {A} 5
XP87-0072 5/16” x 1 1/2” Hex Bolt {B} 6
XP87-0069 5/16” x 2” Hex Bolt {C}
XP87-0029 1/4” Nylock Nut 5
XP87-0047 5/16” Nylock Nut 8
XP87-0027 Nylon Washer 26
XP87-0070 Seat Tension Bolt 1
XP87-0040 Allen Wrench 1
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
Qty
2
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
10
STOP NOW! It will be necessary to use the climbing belt with your full-body fall arrest harness
while ascending the tree and attaching your treestand. As you climb it will be necessary to
slide the climbing belt up the tree. Once you’ve reached the desired height and your treestand
is properly secured to the tree, you will need to attach the permanent tree belt and secure
tether strap as illustrated on page 5 of this manual. FAILURE TO WEAR YOUR FULL-BODY FALL
ARREST HARNESS AT ALL TIMES WHILE USING THIS PRODUCT MAY RESULT IN SERIOUS INJURY OR
DEATH!
WARNING! Prior to installing your X-Stand hang-on treestand, you must install a climbing
system (i.e., stacking sticks, ladders, sectionals, etc.) which meets or exceeds ASTM
standards. Failure to follow these instructions may result in serious injury or death!
WARNING! DO NOT attempt to install this product on a tree that is not straight, healthy, and
devoid of dead branches, limbs, vines, or anything that might interfere with the installation.
DO NOT attempt to install this treestand on a tree that is leaning, diseased, crooked, has
loose bark, or does not meet the minimum installation diameter of nine (9) inches (23 cm) at
treestand height (i.e. seating platform height) or exceeds the maximum installation diameter of
twenty (20) inches (51 cm) at treestand height (i.e. seating platform height).
Failure to follow these instructions may result in injury or death!
STEP 1. Attach the rear frame support to the platform using two (2) 5/16” x 2” hex bolts {C}
eight (8) nylon washers and two (2) 5/16” nylock nuts Tighten securely.
STEP 2. Securely fasten each of the two plastic coated cables to the foot platform using two
(2) 5/16” x 1 ½” hex bolts {B} six (6) nylon washers and two (2) 5/16” nylock nuts.
STEP 3. Securely fasten the other two ends of the plastic coated cables one on each side of
the rear frame support using two (2) 5/16” x 1 ½” hex bolts {B} six (6) nylon washers and two
(2) 5/16” nylock nuts as seen in (Fig 1.)
STEP 4. Securely fasten the seat assembly to the top of the rear frame support using two (2)
5/16 x 1 ½” hex bolts {B} six (6) nylon washers and Two (2) 5/16” nylock nuts
STEP 5. Securely attach the bark biter to the rear frame support using four (4) ¼” x 1 ¼” hex
bolts {A} Make sure bark biter teeth are on top.
STEP 6. Securely attach the seat bar by inserting it into place under the seat front using one
(1) ¼” x 1 ¼” hex bolt {A} recheck every nut and bolt at this time for tightness.
ASSEMBLY INSTRUCTIONS
XSFP444 - PARAGON
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
Foot Platform
[A]
[B]
[C]
[C]
Seat Bar
Seat Tension
Bolt
Allen
Wrench
Plastic
Coated
Cable
Rear Frame
Strap
Post
Strap
Post
Support
Bark
Biter
Seat Assembly
Plastic
Coated
Cable
[B]
[B]
[B]
[B]
[B]
[A]
[A] [A]
[A]
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT. 11
FIGURE 1
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
1
FIELD INSTALLATION
- PARAGON -
STEP 1. Select a straight healthy tree, one
devoid of dead branches with a minimum
diameter of 9” (23 cm) and one that does
not exceed 20” (56 cm) in diameter.
STEP 2. With your climbing system which
meets or exceeds ASTM standards
installed as outlined in the Manufacturer’s
Instruction Manual, you are now ready to
install your treestand. Always maintain
three points of contact when climbing up/
down climbing systems. Always use a pull-
up (hoist) rope to raise and lower your
treestand. Never climb with anything on
your back.
STEP 3. Place the included installation
ratchet straps on your person (do not hold
in hand).
STEP 4. Tie your pull-up (hoist) rope to your
hang – on treestand in a way that you
secure the seat portion to the foot platform
to keep the treestand from opening when
being hoisted. Should the treestand open
while being pulled-up (hoisted) it will
become awkward and dangerously clumsy.
STEP 5. With your treestand attached to the
pull-up (hoist) rope, and the tag-end in your
possession (do not hold in hand), check to
ensure your linesman belt is properly
secured to you and the linesman/climbing
belt is attached to the tree and carefully
climb to the desired height.
STEP 6. Once you reach the desired
treestand installation height, re-check
to ensure your linesman/climbing belt is
properly secured to you and the tree. Make
certain you are balanced and secure on
your climbing system. Next pull-up (hoist)
your hang-on treestand.
STEP 7. With your treestand folded with the
foot platform in the upright position and
rmly in hand, place your treestand against
the tree. (Figure 1). Wrap the ratchet strap
around the tree and secure it to the strap
posts on either side of your treestand.
(Figure 1) NOTE: Make certain the ratchet
strap is not twisted. If the ratchet strap is
twisted, remove and reattach so it is not
twisted. Remove the slack from the ratchet
strap by pulling on the tag-end of the strap.
Engage the ratchet strap and ratchet until
the strap is tight. Repeat this process for
the second ratchet strap.
STEP 8. Lower foot platform to standing
position; the treestand will then snug up to
the tree to prevent any shifting. Repeat as
necessary to accomplish a snug t to the
tree. (FIG. 3)
STEP 9. While remaining attached to the tree
with your linesman belt, attach the tree belt
the full-body fall arrest harness to the tree
trunk at a location above the seat. Both the
linesman belt and tether of the tree belt of
the full body fall arrest harness should be
attached. Disconnect linesman belt and
climb above standing platform and step
down onto the center of the standing
platform. If there is any looseness, step off
the treestand and back onto the climbing
system. Disconnect the treestand and
repeat the previous installation STEPS after
re-connecting your linesmen belt.
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
Ratchet Strap
(Loops At Both Side)
Backrest
Ratchet Strap
(Loops At Both Side)
Ratchet Strap
(Loops At Both Side)
Backrest
Ratchet Strap
(Loops At Both Side)
Ratchet Strap
(Loops At Both Side)
Backrest
Ratchet Strap
(Loops At Both Side)
Ratchet Strap
(Loops At Both Side)
Backrest
Ratchet Strap
(Loops At Both Side)
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT. 1
HANG ON INSTALL - FIGURE 1 HANG ON INSTALL - FIGURE 2
HANG ON INSTALL - FIGURE 3 HANG ON INSTALL - FIGURE 4
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
X-Stand Treestands | 14645 Felton Court, Suite 103 | Apple Valley, MN 55124
ATTENTION!! WHEN YOU SEE A “WARNING!” BE SURE TO HEED THE
MESSAGE! THE INFORMATION CONTAINED IN THESE MESSAGES
CAN SAVE YOUR LIFE!!
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
1
To activate your product’s warranty, please mail in your registration card or submit it online at www. X-Stand.com
HANG-ON AND CLIMBING SYSTEM WARNINGS & PRODUCT REGISTRATION
Product Purchased Model Number
Serial Number
Owner’s Name
Street Address
City State Zip Code
E-mail Address Phone
Date Purchased
Purchased From (Dealer Name)
How did you hear about us: Catalog Webpage Friend Magazine
Other, Please Explain
Are you a: Bow Hunter Gun Hunter Both
Treestand Preference: Fixed Position Climbing Ladderstand
WARNING! DO NOT jump or bounce on the treestand platform (or any of the trees-
tands components) and/or the seat to engage the stand to the tree. Failure to follow these
instructions may result in serious injury or death!
WARNING! Climbing aids (e.g., stick ladders, sectional ladders, etc.) must be installed
and extend a minimum of 24-inches (2 feet) above the seating platform. This practice
allows the user to have a rm hand hold when stepping down onto the foot platform.
NEVER attempt to step up onto your foot platform. Failure to follow these instructions may
result in serious injury or death!
WARNING! NEVER ATTEMPT to step onto a treestand until all treestand contact points
are secured tightly and rmly to the tree. NEVER ATTEMPT to step onto a treestand unless
your full-body fall arrest harness is properly attached. Failure to follow these instructions
may result in serious injury or death!
WARNING! NEVER ATTEMPT to step onto a treestand until all treestand contact points
are secured tightly and rmly to the tree. NEVER ATTEMPT to step onto a treestand unless
your full-body fall arrest harness is properly attached. Failure to follow these instructions
may result in serious injury or death!
WARNING! When installing your hang on treestand, you must wear your full-body fall
arrest harness and use the climbing belt at all times while installing or removing your
xed position treestand. The use of the climbing belt ensures your stable attachment to
the tree until installation is complete. Failure to follow these instructions may result in
serious injury or death!
WARNING! When installing your treestand, never attempt to climb with your treestand
in your possession. Always use a pull up rope to raise and lower the treestand during
installation and removal. NEVER ATTEMPT TO CLIMB WITH ANY HUNTING COMPONENT OR
ACCESSORY IN HAND OR ON YOUR BACK. Failure to follow these instructions may result
in serious injury or death!
WARNING! If you nd that your treestand is unlevel, canted, angled awkwardly
upward or downward, or in any conguration other than level, immediately climb down to
ground-level and readjust your treestand as necessary to alleviate this awkward angle.
Never attempt to hunt from an unlevel treestand. Additionally, never attempt to level your
treestand at heights above the ground. Failure to follow these instructions may result in
serious injury or death!
WARNING! Never install, set-up, or climb to your treestand with a weapon. Use a
pull-up rope to carefully raise your unloaded weapon after full-body fall arrest harness is
secure and you are set in the stand!
WARNING! An ASTM compliant full-body fall arrest harness with a
lineman’s/climbing belt must be worn at all times while installing or
removing any hang-on style treestands or climbing aids (i.e., ladders, sticks,
steps, etc.). Failure to follow these instructions may result in serious injury
or death!
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT. 1
STANDARD LIMITED WARRANTY
Warranty: X-Stand™ Treestands warrant all X-Stand™ treestands, climbing system products and hunting
accessories to be free from defects in material and workmanship for a period of twelve months from
the original date of retail purchase. X-Stand™ Treestands warrants the enclosed hardware (where
applicable) is delivered to be free from physical defects for a period of twelve months from the original
date of retail purchase.
Repair Procedures, Exclusive Remedy: X-Stand™ Treestands will at its option, repair, or replace products
not conforming to this limited warranty at no charge. THIS IS THE SOLE AND EXCLUSIVE REMEDY
AVAILABLE FOR BREACH OF WARRANTY OR UNDER ANY OTHER LEGAL THEORY WITH RESPECT
TO X-STAND™ Treestands. If you nd a product to be defective, contact the customer service
department at 540-877-2769. When you receive authorization, return the product as directed at your
expense. Product repairs not covered by warranty, and product updates, will be provided at a set rate.
Limitations: This warranty is void if the product is damaged by improper or abnormal use or by
accident; if the product is altered or modied in any way other that those directed by ofcial X-Stand™
Treestands instructions; or if any attempt is made to repair the product without authorization from X-
Stand™ Treestands. It is solely the purchaser’s responsibility to determine the suitability of these
products for each particular application. X-Stand™ Treestands products are intended for hunting and
hunting only. X-Stand™ Treestands are in all events not suitable, and are not authorized, for use in any
situations that might pose potentially injurious to life and health, other than those situations that the
products are intended for. This warranty is not assignable or transferable.
No Other Warranties: EXCEPT AS PROVIDED IN THIS LIMITED WARRANTY SET FORTH IN THE
WARRANTY CARD SUPPLIED WITH X-STAND™ TREESTANDS AND INSTRUCTION SHEETS ARE
PROVIDED “AS IS”. ALL OTHER WARRANTIES AND REPRESENTATIONS, ORAL OR WRITTEN,
EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED AND DO NOT
APPLY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HERE OF. Except as required by law, no representative, agent or employee of X-Stand™ Treestands is
authorized to make warranties, representations, or obligations inconsistent with or in addition to those
set forth in this limited warranty.
No Damages: IN NO EVENT WILL X-STAND™ Treestands BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF WARRANTY OR
UNDER ANY OTHER LEGAL THEORY, even if advised of the possibility of such damages. In no event
will X-Stand™ Treestands be liable for sums in excess of the purchase price of the product. X- Stand
Treestands is thus not liable for lost prots or goodwill; downtime; damage or destruction of items or
equipment used with, or in conjunction with, X-Stand™ Treestands; personal injury or loss; or any other
damages.
General: (a) This agreement is the entire agreement between you and X-Stand™ Treestands.;
supercedes any prior or different agreements, representations, or proposals; and may be changed
only by written agreement with X-Stand™ Treestands. (b) Waiver by any party of any default or breach
of this agreement will not constitute a waiver of any subsequent default or breach of the same of
different kind. (c) The invalidity of any provision of this agreement shall not affect the validity of the other
provisions hereof. (d) This agreement shall be governed by the laws of the State of Minnesota, U.S.A.
X-Stand™ Treestands; Apple Valley, MN 55124
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
This X-Stand™ product(s) has been tested to rigid industry standards. Safe operation and use of this X-Stand™ product(s) is the responsibility
of the user(s). Please read and follow all safe use instructions and warnings. Failure to follow these may result in serious injury or death!
First Edition, January 2017, Published by X-Stand™ TREESTANDS, Apple Valley Minnesota.
© 2017 X-Stand™ TREESTANDS. All rights reserved.
Table of contents
