X-Vision XD200 User manual
Model: XD200
High Capacity RF/PIN
Access Control System
Model: XD200
High Capacity RF/PIN
Access Control System
CCTV
Manufactured exclusively for Xvision
www.x-vision.co.uk
CONTENTS
1. Features Introductions
2. Reader Front panel & types of proximity card
3. Operation instructions
Start reader
Mode inquiry
Antiduress
Setup mode
4. Quick setting
5. Setup mode function selection instructions (00~28)
3
4
5
5
5
5
5
6
6
6. Installation instructions
7. Hardware specifications
8. Attentions
9. TROUBLESHOOTING
(01) Add new card
(02) Delete card
(04) Shunt time
(05) Open door mode
(07) Reset to release alarm
(08) Change system password
(09) Reset to release antiduress alarm
(10) Reader ID number
(11) Password error times
(12) Antiduress code
(13) Total cards
(14) Program version
(15) Set time
(16) Set date
(17) Auto record range
(18) Main rea der location
(19) Door shutting time
(20) Alarm mode
(21) Antiduress alarm mode
(22) Door sensing mode
(23) Antitheft sensing mode
(24) Push button door open sensing mode
(25) BEEP sound mode
(26) Print mode
(27) Antipass mode
(28)Display card number mode
(00) Instand door open
(90) Historical Data Inquiry
Reader connector
Wiring connection for additional electric lock and push button door open switch
Wiring connection for additional magnetic door sensing
Wiring connection for antith eft sensing (NO Type)
Wiring connection for additional alarm
Wiring connection for linking with computer
20
20
20
21
21
22
23
24
24
24
ST680 OPERATION INSTRUCTIONS
1. Features introductions
When connecting with computer,it can b e used for d ata inquiry and function s etting
simutaneously.(Door open/close,start a larm system,etc).It can also operate solely to
manage access control.
Function setting can be done by computer or reader itself.(Single registration or
deletion,door open time,etc).
The capacity data in put/output can reach up to 6,000 by single reader operation.When
linking with computer,its data input/output capacity can be unlimited.
Main reader ha s 9,000 card regis tration s capa bility.Each card ca n be selfsetting for
personal password a nd effective in/out time.
Main reader ha s 48 units of time zone.E ach time zone unit also has 5 time ranges for
selfsetting by user.
Exam ple:It can be set from"G" hour "H" minute to "I" hour "J" minute on every
M ondays,We dnesdays,Sa turda ys in periodic of "A" year " B" month "C"
day to"D" year "E" month "F" day as effective in/out time r ange.
Directly link to series type p rinter for direct data prin ting.
Additional subreader for in /out c ontrol.
Equipped with hardware se lftesting function.
Internal batteries will provide power supply when power cu t occurred to prevent any
data from bein g erased and system time can o perate as normal.
Main reader access control's range:
Main reader's sensing range:
＊
＊
＊
＊
＊
＊
Card nu mber
Passwo rd
Time zone
Special holida ys
Error control
Antipa ss
＊
＊
＊
Antitamper
Antitheft
Illegal door open
It must be regi stered before use.
Personal password has to key in to open the d oor.
Setting the effective of year,month,day,time range,Monday~Sunday.
User could set any holidays as to prevent any unauthorized access.
Alarm w ill actvate when"N" times of consecutive error password
entering occurred.
The card could only be used for matching single entry and exit.
(Otherwise,it will be considered the car d has been duplicated
causing access denial.)
When the reader is tampered,alarm will be activated .
Alarm will be activated when sensing any abnormal operations.
Alarm will be activated when door is destroyed and opened by force.
3
Operating Instructions
＊
＊
＊
Antidu ress
Exceed door shut time Alarm will be activated,when door is not closed exceeding intial
tim e setting control.
Door open button sensing Door will open immedia tely when the butto n is pu shed.
It will operate when password and duress code are keyes in to send help
signal to the nearest police station.It must be done manually to disable
antiduress function.
2. Reader Front Panel & Types of Proximity Card
(a) Front Panel Indicator Lights
(b) 10 entry (button),two function ke ys : "#"&" ".＊
(c) Types of prox imity card
(1). POWER (red)
(2). OK ( green)
(3). DENY (yellow)
(4). STATUS (yellow)
# key : input data confirm key (En ter)
key : clear o r escape key (CLR/ESC)＊
: power indicator.
: door open indicator.
: operation error or un regis tered c ard indicator.
: system starts and setup mode indicator.
12345678
4
SC10 : Thin card , thickness 0.8 mm, ISO standard
card dimensions. It can be printed directly
from card printer. Read range
EM 1 25KH z 10 15cm, Mifare 13.56MH z 3 7cm. ： ～ ： ～
SC20 : Thick card , thickness 1 .8 mm, ISO standard
card dimensions. Read range
EM 125KHz 10 20cm ： ～
SC30 : Key tag, dimensions: 5.5L X 7.5H X 3.2W (mm).
Ultrasonic connection, waterproof,
shock proo f. Rea d rang e
EM 125KHz 6 10cm,Mifare 13.56MHz 1.5 4cm ： ～ ： ～
XDRFC - Thin RF Card XDRFC-25 - Pack of 25
Can be printed directly from card printer
Read range: EM 125KHz: 10-15cm. Mifare 13.56MHz: 3-5cm
XDRFHDC - Thick RF Card XDRFHDC-25 - Pack of 25
Read range: EM 125KHz: 6-10cm. Mifare 13.56MHz: 1.5-4cm
XDRFT - High Quality RF Tag XDRFT-25 - Pack of 25 tags
Waterproof, shockproof
Read range: EM 125KHz: 6-10cm. Mifare 13.56MHz: 1.5-4cm
3. Operation instructions
Start reader:It will begin selftesting function when power is switched on.Its operation
procedures are as follow:
LCD DISPLAY
SRAM TESTING
RTC TESTING
INITIAL FUNCTION
<<ST680>> 08:05
0010
INSTRUCTIONS
Memory tesying
Real time clock teseing
Init ial system setting
Model (ST680),present time (08:05),10 registrations.
Note:Card must not exceed the read range (refer to different models) to
gain induction.
a).OK (green) light is on to indicate registered card to gain access.
b).DENY (yellow) light is on and consecutive beeping sound is on to
indicate unregistered card or used under unauthorized time zone.
(Please refer to troubleshooting if neither of above statuses occurred)
Mode inquiry:Press , LCD will display:＊ ＃ ＃MD ADR YYYY/MM/DD
2 001 1999 / 01 / 01
MD
ADR YYYY/MM/DD
: open door mode (2 shows door open by proximity card
sensing, 3 shows door open by proximity card sensing with
password.)
: main reader number. : current date.
Repress to escape. ＊
Antiduress:When under duress, usermay press button before keying
in password to activate alarm.(Duress code presetting is
, it can be changed by user)
Example : antiduress code is , password is ,
then to activate antiduress alarm, the user should key in
.
＊
＊
１ １ ２ ３ ４
１１２３４
Setup Mode:
SYSTEM FUNCTIONS
SELECTION : _ _
User must get into setting mode first before
changing any system functions. User must
key in for system
function selection. is being
set initially by manufacturer.
(Example: User can get into the set up mode
by keying ).
＃ ＃
５ ６ ７８
＃ ５ ６ ７ ８ ＃
system password
System password
5
<<XD200>> 08:05
0010
Model (XD200), Time (08:05), 10 registrations
4. Quick setup:
5. SETTING MODES & FUNCTIONS
User will get into the setup mode as the right diagram shown for any setting
to be made.
(A) Add new card , key in then key in .
(B) Delete card, key in then key in .
(C) Door open time, key in then key in the seconds .
(D) Change reader number, key in then key in the reader number .
(E) Door open mode, key in then key in the mode code .
(F) Time setting, key in then key in the time .
(G) Date setting, key in then key in .
Note: (1)Sunday (2)Monday (3)Tuesday (4)Wednesday (5)Thursday (6)Friday
(7)Saturday
(H) Release alarm, key in , confirmed then press .
( I ) Release antiduress alarm, key in , confirmed then press .
０ １ ０ ０ ０ ０ ０ ０ ０ １
０ ２ ０ ０ ０ ０ ０ ０ ０ １
０ ４ ０ ０ ３
１ ０ ０ ０ ２
０ ５ ２
１ ５ １ ３ ０ ０ １ ５
１ ６ ２ ０ ０ ０ ０ １ ０ １ ６
０ ７ ＃
０ ９ ＃
8dig it card numb er
8digit card number
13 :00:15
2000/01/01 (6)
FUNCTION (01) Add new card:
Either key in 8digit card number or use proximity card to register, both can be
accepted but should be registered prior using.
key in
# syste m pa ssw ord # Key in 01
Key in # or＊
Key in the # or＊
Go in to function 01.
Q ueuing 8dig it card numb er inp ut
key in m anually or by prox imity.
Re gistra tion su ccess ful
be ep sound occurred .
R egis tration repeat ed,b ee p
sound on continuou sly.
back to sy stem function sele ction.
Esc system function select ion.
SYSTEM FUN CT ION
SE LECTION : _ _
ADD ONE CARD
_ _ _ _ _ _ _ _
ADD ONE CARD
0000000 1
ADD ONE CARD
ACCESS DENIAL
Go into sy stem function setu p.
sta tus log ht on,display
function selection.
6
Function (02) D elete card:
Deletion of user's card (such as loss of card or to prevent specific user to gain
access) can be achieved by keying 8digit card number indicated on the
proximity card.
key in
# syste m pa ssw ord #
key in
# syste m pa ssw ord #
Key in 02
Key in 04
Key in # or＊
Key in # or＊
Key in the # or＊
Key in the # or＊
Go in to function 02.
Go in to function 04.
Q ueuing 8dig it card numb er inp ut
key in m anually or by prox imity.
Q ueuing 8dig it card numb er inp ut
key in m anually or by prox imity.
Deletion successful,a
be ep sound occurred .
Deletion successful,a
be ep sound occurred .
NO su ch car d,beep
sound on co ntinuo usly.
NO su ch car d,beep
sound on co ntinuo usly.
back to sy stem function sele ction.
back to sy stem function sele ction.
E sc sys tem function s elec tion.
E sc sys tem function s elec tion.
SYSTEM FUN CT ION
SE LECTION : _ _
SYSTEM FUN CT ION
SE LECTION : _ _
DELETE ONE CARD
_ _ _ _ _ _ _ _
SET SHUNT T IME
(1255):003_ _ _
SET SHUNT T IME
(1255):003 000
SET SHUNT T IME
(1255):003 005
DE LET E ONE CA RD
00000001
DE LET E ONE C AR D
ACCESS DE NIAL
Go into sy stem function setu p.
Go into sy stem function setu p.
sta tus lig ht on,d isplay
function selection.
sta tus lig ht on,d isplay
function selection.
Function (04) Shunt time:
Setting of relay's ON/OFF time in the proximity reader can be set from 01255
seconds. (presetting time is 003 )
7
Function (05) D oor open mode:
Reader has 2 types of identification modes. (presetting figure is 002)
Card proximity door opening: The door will be opened, when the card
is sensed.
Door open by proximity card and password: The door will be opened
by keying additional 4digit password after sensing the registered
card.
Mode (2).
Mode (3).
key in
# syste m pa ssw ord #
key in
# syste m pa ssw ord #
Key in 05
Key in 07
Key in # or＊
Key in # or＊
Key in the # or＊
Press other keys
Go in to function 05.
Go in to function 07.
Queuing the identification
mode input.
Queuing the alarm input
is reset or not.
Wr ong input be ep
so und on continuously.
Se tting s ucces sfully,
ala rm is r eleas ed.
Setting successful ly,
beep s ound occu rr ed .
back to sy stem function sele ction.
back to sy stem function sele ction.
E sc sys tem function s elec tion.
E sc sys tem function s elec tion.
SYSTEM FUN CT ION
SE LECTION : _ _
SYSTEM FUN CT ION
SE LECTION : _ _
AL ARM RE LEA SED
YE S => "#"
Key in the #
Go into sy stem function setu p.
Go into sy stem function setu p.
sta tus lig ht on,d isplay
function selection.
sta tus lig ht on,d isplay
function selection.
Function (07) R eset to release alarm:
User sets to release the alarm.
IDEN TIFICATION
MODE (23) :2
IDENTIFICATION
MODE (23) :1
IDENTIFICATION
MODE (23) :3
8
Function (08) Change system password:
The reader's password is being set at initially by manufacturer.
In order to enter into system setting mode for the first time, user must
key in the initial system password . User may change the system
password after entering into system setting mode.
５ ６７ ８
５６７８
key in
#system pas sword# Key in 08
Key in # or ＊
Key in the # or＊
Go into func tion 08 .
Queuing new s ystem
pa sswor d inpu t.
Input successfully (4 digits).
Error input.
E sc sy stem fu nction selec ti on.
Esc system function s electi on.
SYSTEM FU NCTION
SELECTION : _ _
Go into system function setup.
sta tus light on,disp lay
function s electio n.
INPU T NEW SYSTEM
PASSWO RD : _ _ _ _
CONFIRM SYSTE M
PASSWORD : _ _ _ _
CONFIRM SYSTEM
PASSWORD : 000 0
CONFIRM SYSTEM
PASSWORD : 123 4
INPU T NEW SYSTEM
PASSWO RD : 1234
INPUT NEW SYSTEM
PASSWORD : _12#
Be ep sound on con secutive ly,
error input.(first last 4
digit passw ord different) Reenter new s ystem
password for confirmation.
Inp ut succ essfu lly,(sa me pa ssword)
Function (09) R eset to release antiduress alarm:
User sets to release the antiduress alarm.
key in
# syste m pa ssw ord # Key in 09
Key in # or＊
Press other keys
Go in to function 09.
Queuing for anti duress
alarm r eleased or n ot.
Se tting s ucces sfully,a nti
du res s a larm is released.
back to sy stem function sele ction.
E sc sys tem function s elec tion.
SYSTEM FUN CT ION
SE LECTION : _ _
AL ARM RE LEA SED
YE S => "#"
Key in the #
Go into sy stem function setu p.
sta tus lig ht on,d isplay
function selection.
9
Function (10) R eader ID number:
Each reader has a reader ID number for computer identification and the number
should not be repeated. (presetting figure is 001)
key in
#system pas sword#
key in
#system pas sword#
Key in 10
Key in 11
Key in # or ＊
Key in # or ＊
Key in the # or＊
Key in the # or＊
Go into func tion 10 .
Go in to func tion 11 .
Queuing the identification
mode in put.
Queuing the identification
mode in put.
Wrong inp ut be ep
sound on continuously.
Wrong inp ut be ep
sound on continuously.
S etting succe ssfully,
b eep so und o ccurred.
S etting succe ssfully,
b eep so und o ccurred.
bac k to system function selec tion.
bac k to system function selec tion.
Esc system function s electi on.
Esc system function s electi on.
SYSTEM FU NCTION
SELECTION : _ _
SYSTEM FU NCTION
SELECTION : _ _
Go into system function setup.
Go into system function setup.
sta tus light on,disp lay
function s electio n.
sta tus light on,disp lay
function s electio n.
READER ID N UMBER
(1255) : 001 _ _ _
ER ROR TIME S
(1255) : 003 _ _ _
ERR OR TIMES
(1255) : 003 256
ERROR TI ME S
(1255) : 003 002
READER ID N UMBER
(1255 ) : 0 01 25 6
READER ID NUMBE R
(1255) : 001 002
Function (11) Password erro r times:
Alarm will be activated when "N" times of consecutive error password entering
occurred. (presetting figure is 003)
10
Function (12) Antiduress co de :
Set up of antiduress code ( , ). (presetting code is )＊ ０ ～ ９ ＊
key in
# syste m pa ssw ord #
key in
# syste m pa ssw ord #
key in
# syste m pa ssw ord #
Key in 12
Key in 13
Key in 14
Key in # or＊
Key in # or＊
Key in # or＊
Go in to function 12.
Go in to function 13.
Go in to function 14.
Queuing for antidu ress
code input.
Display total number of
current registered c ards.
Display program version.
Se tting s ucces sfully,
be ep sound occurred .
back to sy stem function sele ction.
back to sy stem function sele ction.
back to sy stem function sele ction.
E sc sys tem function s elec tion.
E sc sys tem function s elec tion.
E sc sys tem function s elec tion.
SYSTEM FUN CT ION
SE LECTION : _ _
SYSTEM FUN CT ION
SE LECTION : _ _
SYSTEM FUN CT ION
SE LECTION : _ _
SET DURESS CODE
09, : _＊ ＊
USER CARD C OUNT
0200
VE RSION : V1.08
SET DURESS COD E
09, :＊ ＊ 9
Key in the # or＊
Pre ss a ny k ey
Pre ss a ny k ey
Go into sy stem function setu p.
Go into sy stem function setu p.
Go into sy stem function setu p.
sta tus lig ht on,d isplay
function selection.
sta tus lig ht on,d isplay
function selection.
sta tus lig ht on,d isplay
function selection.
Function (13) Total cards:
Display total number of current registered cards.
Function (14) Program version:
Display program version.
11
Function (15) Set time:
Example: 18 hour 00 minute 00 second => 18:00:00 (presetting figure is
00:00:00)
ke y in
# system pass wor d#
ke y in
# system pass wor d#
Key in 10
Key in 16
Key in # or ＊
Key in # or ＊
Key in the # or＊
Key in the # or＊
Go in to func tion 1 0.
Go in to func tion 1 6.
Q ueuing for s ystem
ti me inp ut.
Q ueuing for s ystem
date inp ut.
Wrong inp ut, be ep
sound on continuously.
Wrong inp ut, be ep
sound on continuously.
S etting succe ssfull y,
b eep sound o ccurre d.
S etting succe ssfull y,
b eep sound o ccurre d.
bac k to sy stem function selection.
bac k to sy stem function selection.
E sc sys tem fu nctio n selection.
E sc sys tem fu nctio n selection.
SYSTEM FUNCTION
SE LECTION : _ _
SYSTEM FUNCTION
SE LECTION : _ _
Go into sy stem f unctio n setu p.
Go into sy stem f unctio n setu p.
sta tus lig ht on,display
function s election.
sta tus lig ht on,display
function s election.
SET TIME
17 : 50 : 50
SET DATA
199 9/01 /01(5)
SET TIME
17 : 50 : 99
SET DATA
1999/03/29(0)
SET TIME
18 : 00 : 00
SET DATA
1999/03/29(1)
Function (16) Set date:
Example 200 0/04/30 Sunday => 2000/04/30 (1) (presetting is 2000/01/01 (5))
12
Function (17) Auto Record range:
This is to set under what kind of status to save by stand alone operation.
(presetting figure is 003). There are 4 kinds of sta tus to choose:
A. Detect point / output action. (+1) B. Computer special command. (+2)
C. Single reader operation status. (+4) D. User error status. (+8)
Example:
If A and B statuses are chosen, the setting figure for auto record range is 3 (1+2)
If A, B, and D statuses are chosen, the setting figure for auto record range
is 11 (1+2+8)
ke y in
# system pass wor d#
ke y in
# system pass wor d#
Key in 17
Key in 18
Key in # or ＊
Key in # or ＊
Key in the # or＊
Key in the # or＊
Go in to func tion 1 7.
Go in to func tion 1 8.
Q ueuing for auto
re cord r ange input.
Q ueuing for m ain rea der
lo cation input.
Wrong inp ut, be ep
sound on continuously.
Wrong inp ut, be ep
sound on continuously.
S etting succe ssfull y,
b eep sound o ccurre d.
S etting succe ssfull y,
b eep sound o ccurre d.
bac k to sy stem function selection.
bac k to sy stem function selection.
E sc sys tem fu nctio n selection.
E sc sys tem fu nctio n selection.
SYSTEM FUNCTION
SE LECTION : _ _
SYSTEM FUNCTION
SE LECTION : _ _
Go into sy stem f unctio n setu p.
Go into sy stem f unctio n setu p.
sta tus lig ht on,display
function s election.
sta tus lig ht on,display
function s election.
AUTO REC RANGE
(1255) : 012 _ _ _
R EADE R =>0 /INDO OR
1 /OUTD OOR :1
R EADE R =>0 /INDO OR
1 /OUTD OOR :2
R EADE R =>0 /INDO OR
1 /OUTD OOR :0
AUTO REC RANGE
(1255) : 012 256
AUTO REC RANGE
(1255) : 012 011
Function (18) M ain reader location:
To show the location of the reader: (0) Indoor, (1) outdoor. (presetting location
is 001)
13
Function (19) Door shutting time:
Time setting for sensing doorshutting time as to activate the alarm when
exceeding the set value. (presetting value is 030)
ke y in
# system pass wor d#
ke y in
# system pass wor d#
Key in 19
Key in 20
Key in # or ＊
Key in # or ＊
Key in the # or＊
Key in the # or＊
Go in to func tion 1 9.
Go in to func tion 2 0.
Q ueuing for door
shunttin g time input .
Q ueuing for al arm
mode in put.
Wrong inp ut, be ep
sound on continuously.
Wrong inp ut, be ep
sound on continuously.
S etting succe ssfull y,
b eep sound o ccurre d.
S etting succe ssfull y,
b eep sound o ccurre d.
bac k to sy stem function selection.
bac k to sy stem function selection.
E sc sys tem fu nctio n selection.
E sc sys tem fu nctio n selection.
SYSTEM FUNCTION
SE LECTION : _ _
SYSTEM FUNCTION
SE LECTION : _ _
Go into sy stem f unctio n setu p.
Go into sy stem f unctio n setu p.
sta tus lig ht on,display
function s election.
sta tus lig ht on,display
function s election.
DOOR SE NSOR S EC
(1255 ) : 0 30 _ _ _
ALAR M M OD E
( 0/ON ,1 /O FF ) :1
ALARM MOD E
( 0/ON,1/OFF ) :2
ALARM MOD E
( 0/ON,1/OFF ) :0
DOOR SE NSOR S EC
(1255) : 030 256
DOOR SE NSOR S EC
(1255) : 030 015
Function (20) Alarm mode:
(0)shows "ON",(1) shows "OFF ". (presetting figure is 000)
Once set at "OFF" , alarm will not function.
14
Function (21) Antiduress alarm mode:
(0) shows "ON" ,(1) shows "OFF", (presetting figure is 000). Once set at
"OFF", antiduress alarm will not function.
ke y in
# system pass wor d#
ke y in
# system pass wor d#
Key in 21
Key in 22
Key in # or ＊
Key in # or ＊
Key in the # or＊
Key in the # or＊
Go in to func tion 2 1.
Go in to func tion 2 2.
Q ueuing for anti
duress mode input.
Q ueuing for door
sensing mode input.
Wrong inp ut, be ep
sound on continuously.
Wrong inp ut, be ep
sound on continuously.
S etting succe ssfull y,
b eep sound o ccurre d.
S etting succe ssfull y,
b eep sound o ccurre d.
bac k to sy stem function selection.
bac k to sy stem function selection.
E sc sys tem fu nctio n selection.
E sc sys tem fu nctio n selection.
SYSTEM FUNCTION
SE LECTION : _ _
SYSTEM FUNCTION
SE LECTION : _ _
Go into sy stem f unctio n setu p.
Go into sy stem f unctio n setu p.
sta tus lig ht on,display
function s election.
sta tus lig ht on,display
function s election.
ANTIDURESS MODE
(0/ON,1/OFF ) :1
D OOR S ENSOR MO DE
(0 /ON,1 /OFF) :0
D OOR S ENSOR MO DE
(0 /ON,1 /OFF) :2
DOOR SENSOR MODE
(0/ON,1/OFF) :1
ANTIDURESS MODE
(0/ON,1/OFF ) :2
ANTIDURESS MODE
(0/ON,1/OFF ) :0
Function (22): Door sensing mode:
(0) shows "ON", (1) shows "OFF". (presetting figure is 000). Once set at "OFF",
the sensing mode will not function at any abnormal door opening.
15
Function (23) Antitheft sensing mode:
(0) shows "ON", (1) shows "OFF". (presetting figure is 000). Once set at
"OFF", the sensing mode will not function at any cases of broken in.
ke y in
# system pass wor d#
ke y in
# system pass wor d#
Key in 23
Key in 24
Key in # or ＊
Key in # or ＊
Key in the # or＊
Key in the # or＊
Go in to func tion 2 3.
Go in to func tion 2 4.
Q ueuin g for a nti
th eft mo de inp ut.
Q ueuin g for p ush bu tton
switch mode i nput.
Wrong inp ut, be ep
sound on continuously.
Wrong inp ut, be ep
sound on continuously.
S etting succe ssfull y,
b eep sound o ccurre d.
S etting succe ssfull y,
b eep sound o ccurre d.
bac k to sy stem function selection.
bac k to sy stem function selection.
E sc sys tem fu nctio n selection.
E sc sys tem fu nctio n selection.
SYSTEM FUNCTION
SE LECTION : _ _
SYSTEM FUNCTION
SE LECTION : _ _
Go into sy stem f unctio n setu p.
Go into sy stem f unctio n setu p.
sta tus lig ht on,display
function s election.
sta tus lig ht on,display
function s election.
ANTITHEFT MODE
(0/ON,1/OFF ) :0
PUSH BUTTON MO DE
(0/ON,1/OFF ) :0
ANTITHEFT MODE
(0/ON,1/OFF ) :2
PUSH BUTTONMO DE
(0/ON,1/OFF ) :2
ANTITHEFT MODE
(0/ON,1/OFF ) :1
PUSH BUTTONMO DE
(0/ON,1/OFF ) :1
Function (24) Push button door opening s ensing mode:
(0) shows "ON", (1) shows "OFF". (presetting figure is 000). Once set at
"OFF', the sensing mode will not function if the push button is pressed.
16
Function (25) BEEP sound mode:
(0) shows "ON", (1) shows "OFF". (presetting figure is 000). Once set at "OFF"
, the BEEP sound will not function.
ke y in
# system pass wor d#
ke y in
# system pass wor d#
Key in 25
Key in 26
Key in # or ＊
Key in # or ＊
Key in the # or＊
Key in the # or＊
Go in to func tion 2 5.
Go in to func tion 2 6.
Q ueuin g for B EEP
sound m ode input.
Q ueuin g for B EEP
sound m ode input.
Wrong inp ut, be ep
sound on continuously.
Wrong inp ut, be ep
sound on continuously.
S etting succe ssfull y,
b eep sound o ccurre d.
S etting succe ssfull y,
b eep sound o ccurre d.
bac k to sy stem function selection.
bac k to sy stem function selection.
E sc sys tem fu nctio n selection.
E sc sys tem fu nctio n selection.
SYSTEM FUNCTION
SE LECTION : _ _
SYSTEM FUNCTION
SE LECTION : _ _
Go into sy stem f unctio n setu p.
Go into sy stem f unctio n setu p.
sta tus lig ht on,display
function s election.
sta tus lig ht on,display
function s election.
BEEP MOD E
(0/ON,1/OFF ) :0
BEEP MOD E
(0/ON,1/OFF ) :1
BEEP MOD E
(0/ON,1/OFF ) :2
BEEP MOD E
(0/ON,1/OFF ) :2
BEEP MOD E
(0/ON,1/OFF ) :1
B EEP MOD E
( 0/ON,1 /O FF ) :0
Function (26) Print mode:
(0) shows "ON", (1) shows "OFF". (presetting figure is 001) Once set at "ON",
stored data can be printed out immediately.
17
Function (27) Antipass mode:
(0) shows "ON", (1) show s "OFF". (presetting figure is 001) Once set at "ON"
, the card could only be used for matching single entry and exit. This is to
prevent double entry by using the same card if card has been duplicated.
ke y in
# system pass wor d#
ke y in
# system pass wor d#
Key in 27
Key in 28
Key in # or ＊
Key in # or ＊
Key in the # or＊
Key in the # or＊
Go in to func tion 2 7.
Go in to func tion 2 8.
Q ueuin g for a nti
pass mode input.
Queuing for display card
unmbe r mode input.
Wrong inp ut, be ep
sound on continuously.
Wrong inp ut, be ep
sound on continuously.
S etting succe ssfull y,
b eep sound o ccurre d.
S etting succe ssfull y,
b eep sound o ccurre d.
bac k to sy stem function selection.
bac k to sy stem function selection.
E sc sys tem fu nctio n selection.
E sc sys tem fu nctio n selection.
SYSTEM FUNCTION
SE LECTION : _ _
SYSTEM FUNCTION
SE LECTION : _ _
Go into sy stem f unctio n setu p.
Go into sy stem f unctio n setu p.
sta tus lig ht on,display
function s election.
sta tus lig ht on,display
function s election.
A NTIPA SS M ODE
(0 /ON,1 /OFF) :1
D ISPLAY USE R ID
(0 /ON,1 /OFF) :0
D ISPLAY USE R ID
(0 /ON,1 /OFF) :2
D ISPLAY USE R ID
(0 /ON,1 /OFF) :1
A NTIPA SS M ODE
(0 /ON,1 /OFF) :2
A NTIPA SS M ODE
(0 /ON,1 /OFF) :0
Function (28) D isplay card number mode:
(0) shows "ON", (1) shows "OFF". (presetting figure is 000). Once set at "OFF",
LCD will not display the card number.
18
Function (00) Instant door open:
Authorized personnel could get into the setup mode to open the door when any
emergency cases happened.
ke y i n
# sys tem pa s swo rd#
key in
#system password#
Key in 00
Key in 90
Key in＊
Date Tim e
000 1 12 345 6 78 1 7
04/01/01 16:30
OPEN DOOR
YES = > " # "
Key in # or＊
Key in # or＊
Go into functi on 00.
Go into function 00.
Que uing for doo r
ope n inpu t.
Setting successfully,
beep sound occurred.
back t o system function selection.
Esc system func tion se lection.
Esc system function selection.
SYSTEM FU NCTION
SELECTION : _ _
SYSTEM FUNCTION
SELECTION : _ _
Key in th e #
Press other key
Go into system fun ction s etup.
Go into syste m function s etup.
status light on,display
function selection.
status light on,display
funct ion sel ection.
Function (90) H istorical Data Inquiry:
Inquiring historical data from standalone unit.
Press 1: Minus one 2: A dd one 3: Minus 10 4: Add 10 5: Middle
State:
01 Enter 06 Push Button Door Open
02 Exit 17 Invalid Card No.
03 Reader has already been taken apart 24 System Door Open
19
6. Reader installation instruc tions
(1)Reader connector
Yellow
Pu rple
Blue
Green
Brown
Re d
Pu rple
Blue
Gre en
Brown
Re d
PWM
Sub Reader connecto r 1.
Sub Reader connecto r 2.
Output power,positive 5V
Output power,negative GND
G ND
A nti du ress o utput termin al (low active )
D oor s ensing termi n al 2
D oor s ensing termi n al 1
A nti th eft sen sing ter mina l (low act ive )
P ush b utton d oor open po int terminal
Pu rple
Blue
Green
Yellow
Orange
Brown
Black
Re d
Alarm Relay terminal N. O or N.C
Alarm Relay terminal COM
Door open r ela y ( N .O or N.C) t e rmina l
Door open r ela y ( C omm on) ter minal
Signa l (data ) rec eiver
Signa l (data+) tra nsmitt er
Input power,ne ga tive GN D
Input power,positive 12V
ST680 Wiring diagram
6 P IN
CONNECTO R
5 PIN CONNECTOR
8 PIN CONNECTOR 6 PIN CONNECTOR
Push butt on swit ch
Di ode s white c olor termina l
N ude type
ele ctrica l lock
RS 232/RS48 5 Swi tch
RS232 RS485
8 P IN
CONNECTO R
Note: (1) Door open relay electrical rating is 2A/24 VDC.
(2) Push button door open / door sensing / antitheft sensing all are
connection terminal. Any other power supplying is not allowed.
(3) In order to avoid any disturbance of read range, user is advised to
use two separate adaptors.
(4) Related position of reader connector: Please refer to Appendix A.
(2) Wiring connection for additional electric lock and push button door open
switch.
As of different types of electric lock, the wiring methods are also different .
Overall, there are two types of wiring instructions as below:
(a) Fail secure :
Jump Adjustment
(JP10)
R BK BR O Y G BL P R BR G BL P Y
AP10
DC 12 V
AP10
DC 12 V
A EL
-
-
N. O Output
20
XD200 Wiring Diagram
Table of contents
Popular IP Access Controllers manuals by other brands
Motorline professional
Motorline professional MPXR82MFS User/Install manual
ZKTeco
ZKTeco SpeedFace M1 user manual
Tenda
Tenda M3 user manual
SRS Labs
SRS Labs MPROX Installation and hardware guide
SDC
SDC 950 ENTRYCHECK Installation & programming instructions
BKT Elektronik
BKT Elektronik ACBS Installation and configuration manual