X-Vision XP1080S20 User manual

XP1080S20
Quick Installation Speed Dome Installation Manual
Version 1.0

2
Table of Contents
1QUICK INSTALLATION SPEED DOME INSTALLATION........................................7
1.1 Installation Preparation........................................................................................................................................7
1.2 Installation ................................................................................................................................................................8
1.2.1 Address and Baud Rate Setup ....................................................................................................................8
1.2.2 Install the transparent cover .........................................................................................................................9
1.2.3 Install the speed dome..................................................................................................................................10
1.3 Initial Setup ...........................................................................................................................................................12
1.4 Dial Switch Setup................................................................................................................................................12
1.4.1 Communication protocol and Baud rate .................................................................................................12
1.4.2 Address Setup.................................................................................................................................................13
2BRACKET DIMENSIONS...........................................................................................14
2.1 Wall mount bracket.............................................................................................................................................14
2.2 Hanging mount bracket (Multiple Lengths)................................................................................................14
2.3 Corner mount bracket........................................................................................................................................15
2.4 Pole mount bracket ............................................................................................................................................15
3WALL MOUNT BRACKET INSTALLATION ............................................................ 16
3.1 Component Installation.....................................................................................................................................16
3.2 Installation .............................................................................................................................................................16
3.2.1 Installation Requirements ............................................................................................................................16
3.2.2 Installation Steps ............................................................................................................................................16

3
4HANG MOUNT BRACKET INSTALLATION............................................................ 18
4.1 Component Installation.....................................................................................................................................18
4.2 Installation .............................................................................................................................................................18
4.2.1 Installation Requirements ............................................................................................................................18
4.2.2 Installation Steps ............................................................................................................................................18
5CORNER MOUNT BRACKET INSTALLATION......................................................20
5.1 Component Installation.....................................................................................................................................20
5.2 Installation .............................................................................................................................................................20
5.2.1 Installation Requirements ............................................................................................................................20
5.2.2 Installation Steps ............................................................................................................................................20
6POLE MOUNT BRACKET INSTALLATION.............................................................22
6.1 Installation .............................................................................................................................................................22
6.1.1 Installation Requirements ............................................................................................................................22
7APPENDIX ⅠTHUNDER PROOF AND SURGE PROTECTION..........................24
8APPENDIX ⅡABOUT RS485 BUS .......................................................................... 25
8.1 RS485 Bus Main Feature.................................................................................................................................25
8.2 RS485 Bus Transmission Distance..............................................................................................................25
8.3 The Problem in Practical Use.........................................................................................................................25
8.4 RS485 Bus FAQ..................................................................................................................................................26

4
Welcome
Thank you for purchasing our speed dome!
Please read the followingsafeguards and warnings carefullybefore you install or use the
product!

5
Important Safeguards and Warnings
Safety Measures
Qualified Engineer Needed
The installation engineer or maintenance engineer shall have corresponding CCTVsystem
installation certificate or maintenance qualification certificate.
The installation engineer or maintenance engineer shallhave qualification certificate for work
at height.
The installation engineer or maintenance engineer shallhave the basic knowledge and
operation technique for low-voltage cable layout and low-voltage electronic cable connection.
Please read the installation manual carefullyand keep it well for future reference,
We are not liable for any problems caused by unauthorized modifications or attempted repair.
Lifting Appliance Requirement
Please select the proper speed dome installation mode and use the lifting appliances at the
safety environment.
The lifting appliances shall have the enough capacity to reach the installation height.
The lifting appliances shall have safe performance.
Precautions

6
Safety Transportation
Heavy stress, violent vibration or water splash are not allowed during transportation, storage
and installation.
This series product must use split type package during the transportation.
We are not liable for any damage or problemresulting from the integrated package during
the transportation.
When device is malfunction
Shut down the device and disconnect the power cable immediately if there is smoke, abnormal
smell or abnormal function. Please contactyour local retailer ASAP.
Do not try to dismantle or modify the device
There isrisk of personal injury or device damage resulting from opening the shell.
Please contact your local retailer if there is internal setup or maintenance requirement.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
Do not allow other object falling into the device
Please make sure there is no metal or inflammable, explosive substance in the speed dome.
The above mentioned objects in the device may result in fire, short-circuit or damage.
Please shutdown the deviceand disconnect the power cable if thereis water or liquid falling
into the camera. Please contact your local retailer ASAP.
Please pay attention to the camera. Avoid the sea water or rain to erode the camera.
Handle carefully
Do not allow this series product fall down to the ground.
Avoid heavy vibration.
Installation Environment Requirement
Thisseries speed dome should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
This series product shallbe away from the strong electromagnetism radiant, please keep it
away fromwireless power, TV transmitter,transformer and etc.
Daily Maintenance
Please use the soft cloth to clean dust on the shell, or you can use soft cloth with cleaning
liquid to clean the shell and then use soft cloth to make it dry.
Do not use gasoline, dope thinner or other chemical material to clean the shell. It may result
in shelltransfiguration or paint flake.
Do not allow the plastic or rubber material to touch the shell for a long time. It may resultin
paint flake.

7
1QUICK INSTALLATION SPEED DOME INSTALLATION
1.1 Installation Preparation
Basic Requirement
All installation and operation here should conformto your local electricalsafety codes.
Before installation, please open the package and check all the componentsare included.
Please make sure the speed dome installation environment and installation mode can meet
your requirement. If there is special requirement, please contact your local retailer for more
information.
We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
Check installation space and installation location intension
Please make sure the installation environment has enough space to install the speed dome and
its corresponding bracket.
Please make sure the ceiling, wall and the bracket can support the speed dome and its
corresponding installation component. The safetyfactor shallbe 4X.
About cable
Please select the cable according to your transmission distance.
The minimum video coaxial-cable requirement is:
75 ohm.
Fullcable with copper conductor
95% knitted copper shield
International Model
Max Distance
(Ft\M)
RG59/U
750ft (229m)
RG6/U
1,000ft (305m)
RG11/U
1,500ft (457m)
Set dial switch button
Set dial switch button according to control protocoland speed dome address. (Please refer to
user’s manual for detailed information.)
Please keep all package material well for future use
Please keep speed dome package material well in case you need to send it back to your local
retailer or manufacturer for maintenance work.
Non-originalpackage material may result in device damage during the transportation.
Check Accessories
Before the installation, please check the accessories one by one according to the packing list.
Please make sure all the components listed are includes.
Important:
The quick installation speed dome poweris AC 24V/3A.

8
1.2 Installation
Please note the quick installation speed dome includes the quickinstallation high speed dome,
IP quick installation speed dome, tracing quick installation high speed dome, quick installation
medium speed dome.
The speed dome has several types of installation brackets. You can refer to the following
contentsfor detailed information. Here we are going to install the speed dome in wall mount
bracket.
Open the transparent cover and take out the packing material EPE around the speed dome driver.
Please remove the protective paster fromthe driver and take off the camera lens cap. See Figure
1-1.
Figure 1-1
1.2.1 Address and Baud Rate Setup
Now you can set the quickinstallation speed dome address and baud rate. The speed dome
interface is shown as below. See Figure 1-2. There are two dial switches: SW1 and SW2. Here
you can set the address, baud rate, communication protocol and etc. Please refer to chapter 1.4
for detailed information.
Figure 1-2

9
1.2.2 Install the transparent cover
First, you need to check the steelwire of the bracket is firmly secure or not.
Please line up the captive screws to the quadrate groove of the bracket and then push the
bracket into the internalenclosure.Fix these two captive screws. See Figure 1-3.
Figure 1-3
Now you can install the quick installation port. Please twist Teflon tape around the screw thread
of the quick installation port and turn it into the screw thread of the wall mount bracket. Use M4
stainless screws to secure firmly. See Figure 1-4.
Figure 1-4
Now you can begin the cable connection.
Connect the steel wire of the quick installation cover to the hook of the quick installation port.
Connect the reserved integration cable of the wall mount bracket to the corresponding power
cable, video output cable, RS485 control cable, alarm input/output port(if necessary) of the
multiple-function composite cable of the quick installation speed dome. Paste the insulating tape
in the connection position to do the proper waterproof work. See Figure 1-5.

10
Figure 1-5
Note
The video portis covered the heatshrink tube of highshrinkingratio. After the video
connection, please heat the tube to make sure the video port is damp proofand water
proof.
1.2.3 Install the speed dome
After you complete the above steps, please pull the integration cable and multiple-function
composite cable to the wall mount bracket.
Line up the straight edge of the internalenclosure of the quick installation speed dome to the
straight edge of the quick installation port, and then push the speed dome to the bottom of the
port slowly. Use your handsto turn the three stainless screws of the quick installation port to the
groove of the internal enclosure of the quick installation speed dome. Turn the stainless screwof
straight edge of the quick installation port to the Ф6.5 hole of the straight edge of the internal
enclosure of the quick installation speed dome. Use the inner hex tool to fix these three stainless
screws. Now you have completed the installation. See Figure 1-6.

11
Figure 1-6
Important
After the installation, please make sure:
The three stainlessscrews of the quick installation port are firmly secure.
The quick installation speed dome is fixed.
The speed dome is straight.
The steel wire connection is firm.
After your installation, the interface is shown as in Figure 1-7.
Figure 1-7

12
1.3 Initial Setup
The default setup is:
Address: 1
Baud rate: 9600
1.4 Dial Switch Setup
The two dial switches of the speed dome are SW1 and SW2. These are to specify the speed
dome parameter such as protocol, baud rate, address and etc.When the button is ON, it is 1. In
the SW1 and SW2, 1 is the lowest bit and the 8 is the highest bit. See Figure 1-8.
Please note this series speed dome cans automatically recognize the DH-SD, PELCO-D.
PELCO-P. Usually you do not needto set the protocol.
Figure 1-8
1.4.1 Communication protocol and Baud rate
Please refer to the protocol sheets for detailed information.
Protocol
Baud rate
Parity
1
2
3
4
5
6
7
8
1
2
3
4
Communication Protocol
OFF
OFF
OFF
OFF
DH-SD （Compatible with China
industrialstandard protocol）
ON
OFF
OFF
OFF
PELCO-D
OFF
ON
OFF
OFF
PELCO-P
X
X
X
X
Reserved
Please refer to the baud rate sheet for detailed information.
5
6
Baud Rate
OFF
OFF
9600bps
ON
OFF
4800bps

13
OFF
ON
2400bps
ON
ON
1200bps
Please refer to the paritysetup sheet for detailed information.
7
8
Parity
OFF
OFF
NONE
ON
OFF
EVEN
OFF
ON
ODD
ON
ON
NONE
1.4.2 Address Setup
The speed dome address setup interface is shown as below. See Figure 1-9.
Figure 1-9
The encode mode adopts binary system. 1 to 8 is valid bit. The highest address bit is 255. You
can refer to the following sheet for more information.
Address
1
2
3
4
5
6
7
8
1
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
5
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
6
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
7
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
……
…………………………………………………………………
254
OFF
ON
ON
ON
ON
ON
ON
ON
255
ON
ON
ON
ON
ON
ON
ON
ON

14
2BRACKET DIMENSIONS
2.1 Wall mount bracket
The wall mount bracketdimensions are shown as below. See Figure 2-1.
Figure 2-1
2.2 Hanging mount bracket (Multiple Lengths)
The hanging mount bracket is shown asbelow. See Figure 2-2.
Figure 2-2
The bracket length setup values are：
200mm
300mm
500mm
You just need to replace the
connection pole.

15
2.3 Corner mount bracket
The corner mount bracket is shown as below. See Figure 2-3.
Figure 2-3
2.4 Pole mount bracket
The corner mount bracket is shown as below. See Figure 2-4.
Figure 2-4

16
3WALL MOUNT BRACKET INSTALLATION
3.1 Component Installation
Wall mount bracket is shown as below. See Figure 3-1.
Figure 3-1
3.2 Installation
3.2.1 Installation Requirements
The wall mount speed dome can be installed in the hard construction wall in the indoor or
outdoor environments. Before the installation, please make sure:
The wall is thick enough to install the expansion bolt.
The wall can at least sustain the 4x weight of the speed dome.
3.2.2 Installation Steps
Please draw four holesposition in the wall according to the hole of the bottomof the wall mount
bracket. Then you can dig four holes and insert the expansion bolts (not provided). Use four hex
bolts and flat washer to fix the bracket in the expansion bolts. See Figure 3-2.
Figure 3-2
Installation
Hole

17
Install the speed dome in the bracket. See Figure 3-3.
Figure 3-3
Please refer to chapter 1.2 for detailed installation information.

18
4HANG MOUNT BRACKET INSTALLATION
4.1 Component Installation
Hang mount bracket and its components are shown as below. See Figure 4-1.
Figure 4-1
4.2 Installation
4.2.1 Installation Requirements
The hang mount speed dome can be installed in the hard construction wall in the indoor or
outdoor environments. Before the installation, please make sure:
The wall is thick enough to install the expansion bolt.
The wall can at least sustain the 4x weight of the speed dome.
4.2.2 Installation Steps
Loosen the M4 bolt in the flange side to separate the flange and steeve. Pull the integration cable
through the airproof slot of the bottomof the flange and then connect to the centre hole of the
flange. Please secure the flange in the ceiling. See Figure 4-3. Please note, if the speed dome
is installedin the outdoor environments, you needto paste the silica gel on the surface of
the flange and the surface andthe cable exit.
Figure 4-2
Figure 4-3
Silica gel
Connect to flange

19
Pull the cable through the steeve and then secure the steeve to the flange. Fixthe M4 bolt.
Please note, if the speed dome is installed in the outdoor environments, you need to paste
enough Teflon tape at the top screw thread of the steeve and then turn the steeve to the flange
firmly. Please paste the silica gel on the steeve connection surface to do the waterproof work.
See Figure 4-4.
Figure 4-4
Please draw four holesposition in the wall according to the hole of the bottomof the wall mount
bracket. Then you can dig four holes and insert the expansion bolts (not provided). . Use four
hexbut and flat washer to fix the bracket in the expansion bolts. See Figure 4-5.
Figure 4-5
Please refer to chapter 1.2 for detailed installation information.
Teflon tape
M4 bolt
Silica gel
Long pole Without pole

20
5CORNER MOUNT BRACKET INSTALLATION
5.1 Component Installation
Corner mount bracket and its components are shown as below. See Figure 5-1.
Figure 5-1
5.2 Installation
5.2.1 Installation Requirements
The corner mount speed dome can be installed in the hard construction wall in the indoor or
outdoor environments where there is a 90 degrees angle. Before the installation, please make
sure:
The wall is thick enough to install the expansion bolt.
The wall can at least sustain the 4x weight of the speed dome.
5.2.2 Installation Steps
Please draw four holesposition in the wall according to the holes of the corner installation
accessories. See Figure 5-2.
Figure 5-2
Then you can dig four holes and insert the M8 expansion bolts. Pull the power cable,
video/controlcable and the alarm cable through the centre hole of the bottom of the corner
bracket, the waterproof adhesive, and the centre of the bracket. Please reserve the enough cable
connection length and then use the M8 expansion bolt to secure the corer mount bracket chassis
on the wall. See Figure 5-3.
Installation hole