Xantech XT-4K-VIP-TX User manual

XT-4K-VIP-TX/RX QUICK REFERENCE GUIDE
®
© 2019 XANTECH®is a registered trademark of Nortek Security and Control, LLC. 10023196_RevA10_Quick_Reference_Guide_Xantech_XT_4K-VIP_TXRX_1005_WEB
XT-4K-VIP-TX/RX
Quick Reference Guide
Important Note:
The Xantech Premium Video over IP (VIP) platform distributes HDMI video over 1GB Managed network hardware.
It is advised that Xantech VIP products are connected on an independent network switch to prevent unnecessary
interference, or reduction in signal performance due to the bandwidth requirements of other network products.
Please read the full product manual (available to download online at www.xantech.com) and ensure that the
network switch is congured correctly prior to connecting any Xantech VIP products. Failure to do so will result in
problems with conguration of the system and/or video performance.
Introduction
The Xantech Premium Video over IP (VIP) platform enables distribution of HDMI video over a 1Gb Network switch.
The XT-4K-VIP-TX and XT-4K-VIP-RX are HDCP 2.2 compliant Transmitters and Receivers that use visually lossless
compression technology to deliver HDMI, Bi-directional IR, RS-232 and USB/KVM up to lengths of 100m over standard
network architecture. The XT-4K-VIP-TX/RX can be powered via PoE from a Network switch or powered locally should
a switch either not be used or not support PoE. With multiple conguration options available, this Video over IP solution
is ideal for both commercial and residential installations.
Features
• Advanced UHD video over 1Gb Network
• Virtually unlimited system size
• Connect to any supported Layer 2 / Layer 3 Managed Switch for HDMI video distribution
• Supports up to 4K HDR UHD video (3840 x 2160 @ 30Hz 4:4:4, 4096 x 2160 @ 24Hz 4:4:4, and 4K @ 60Hz
4:2:0)
NOTE: HDR support is dependant on video signal bandwidth. Please see table in product manual for reference
• Supports all known HDMI audio formats including Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio
transmission
• Video up-scaling and down-scaling
•Features 4 operational modes:
- Matrix distribution (Requires 1Gb network switch)
- Video wall (Requires 1Gb network switch)
- One-to-one HDMI extender (No network switch required)
- One-to-many HDMI splitter (No network switch required)
• HDCP 2.2 Compliant
• Advanced EDID management
• Analog L/R audio embedding and de-embedding on XT-4K-VIP-TX Transmitter
• Analog L/R audio breakout on XT-4K-VIP-RX Receiver
• Bi-directional RS-232 and IR pass through
• USB 2.0 connectivity (backwards compatible with USB 1.1) for KVM and other USB devices
• PoE (Power over Ethernet) to power Xantech products from PoE switch
• Local 24V 1A power input should network switch not support PoE, sold separately
•Simple conguration via web-GUI through the XT-4K-VIP-ACM
• HDMI audio embedding supports up to 192 Khz, XT-4K-VIP-RX analog audio output supports up to 96Khz only
• RS-232, IR and Telnet/IP integration for control of the VoIP system using Xantech XT-4K-VIP-ACM
Settings
Default IP Address: 169.254.100.254 (TX & RX)
Username: xantech
Password: 1234
10023196_RevA9_Quick_Reference_Guide_Xantech_XT_4K-VIP_TXRX_0304_PRINT.indd 1 03/04/2019 09:51

XT-4K-VIP-TX/RX QUICK REFERENCE GUIDE
®
XT-4K-VIP-TX Front Panel
161514131210
21 3 78
9
1 Conguration Up/Down - Used to congure XT-4K-VIP-TX manually and apply ‘Programming mode’
2Transmitter ID status window - Displays Tranmsitter’s ID information
3Assignable bi-directional RS-232 ports – Connect to third party control device to extend RS-232 commands to any/
multiple XT-4K-VIP product’s RS-232 port
4Firmware Micro-B USB port - Used to update XT-4K-VIP-TX MCU rmware
5MCU rmware update switch - Used to place Transmitter product into rmware update mode
6Reset button - Press once briey to reboot the product or press and hold for 5 seconds to factory reset
7Type-B USB port - USB connection for USB/KVM routing within VIP system
8Power LED indicator - Flashing status light when the unit is booting. Solid status light when nished booting
9Link LED indicator - Flashing status light when the unit has booted and is ready. Solid status light when sending
video
qPower port – Use 24V 1A DC adaptor (sold separately) if not using a PoE network switch
wLAN Connection (PoE) - Connect to Layer 2 / Layer 3 Managed Switch for HDMI video distribution
eHDMI input – Connect to a HDMI source
rIR IN (IR input) – 3.5mm stereo jack. Transmits IR to any XT-4K-VIP-RX receiver currently viewing the XT-4K-
VIP-TX. Please use a Xantech I2V IR Receiver (sold seperately). When using the Xantech IR Receiver (optional)
ensure cable direction is correct
t IR Flasher (IR output) - 3.5mm mono jack. Routes IR from any XT-4K-VIP-RX (IR IN) allowing source control. Use
Xantech 12V IR emitters (sold seperately)
yL/R analog audio line input - Used to embed analog audio onto HDMI signal
uL/R analog audio line output - 2 channel audio breakout from the HDMI source that supports 2 channel PCM up to
192Khz
NOTE: Conguration of Xantech XT-4K-VIP-TX products can be achieved manually or using the XT-4K-VIP-ACM.
Please see the full product manual (available online at www.xantech.com) for further details.
XT-4K-VIP-TX Rear Panel
Panel Description - XT-4K-VIP-TX Transmitter
456
8
11
10023196_RevA9_Quick_Reference_Guide_Xantech_XT_4K-VIP_TXRX_0304_PRINT.indd 2 03/04/2019 09:51

XT-4K-VIP-TX/RX QUICK REFERENCE GUIDE
®
© 2019 XANTECH®is a registered trademark of Nortek Security and Control, LLC. 10023196_RevA10_Quick_Reference_Guide_Xantech_XT_4K-VIP_TXRX_1005_WEB
XT-4K-VIP-RX Front Panel
1514131211
1Type-A USB ports - USB 2.0 connections for USB/KVM routing within VIP system
2 IR Flasher (IR output) - 3.5mm mono jack – Routes IR from any XT-4K-VIP-TX (IR IN) allowing local equipment
control. Use Xantech 12V IR emitters (sold seperately)
3IR IN (IR input) – 3.5mm stereo jack. Transmits IR to currently selected XT-4K-VIP-TX transmitter allowing routed
IR control of sources. Please use a Xantech 12V IR Receiver (sold seperately). When using the Xantech IR
Receiver (optional) ensure cable direction is correct
4Transmitter Select Up/Down - Used to scroll through sources (XT-4K-VIP-TX), setup XT-4K-VIP-RX manually, and
apply ‘Programming mode’
5Transmitter ID status window - Displays currently selected XT-4K-VIP-TX Transmitter ID
6Assignable bi-directional RS-232 port – Connect to third party control device to extend RS-232 commands to any/
multiple XT-4K-VIP product’s RS-232 port
7Reset button - Press once briey to reboot the product or press and hold for 5 seconds to factory reset
8Firmware Micro-B USB port - Used to update XT-4K-VIP-RX MCU rmware
9Power LED indicator - Flashing status light when the unit is booting. Solid status light when nished booting
qLink LED indicator - Flashing status light when the unit has booted and is ready. Solid status light when receiving
video
wLAN Connection (PoE) - Connect to any supported Layer 2 / Layer 3 Managed Switch for HDMI video distribution
eLOOP OUT - Connect to LAN connection on subsequent XT-4K-VIP-RX unit for daisy-chain of video IP stream
rHDMI output – Connect to a HDMI display
tMCU rmware update switch - Used to place Receiver product into rmware update mode
yL/R analog audio line output - Used to breakout analog audio from HDMI signal
NOTE: Source input must be PCM 2 channel audio for analog audio outputs to work. VIP products do not down-
mix multi-channel audio signals. Audio outputs are xed line level output and RX supports up to 96Khz audio
formats only
uPower port – Use 24V 1A DC adaptor (sold separately) if not using a PoE network switch
NOTE: Conguration of Xantech XT-4K-VIP-RX products can be achieved manually or using the XT-4K-VIP-ACM.
Please see the full product manual (available online at www.xantech.com) for further details.
XT-4K-VIP-RX Rear Panel
Panel Description - XT-4K-VIP-RX Receiver
2356
10
1489
16
7
10023196_RevA9_Quick_Reference_Guide_Xantech_XT_4K-VIP_TXRX_0304_PRINT.indd 3 03/04/2019 09:51

XT-4K-VIP-TX/RX QUICK REFERENCE GUIDE
®
Specications:
XT-4K-VIP-TX
• Video input: 1 x HDMI Type A, female
• Audio input: 1 x 3.5mm L/R analog audio
• Audio output: 2 x RCA L/R analog audio
• Video output/Ethernet port: 1 x LAN RJ45 connector
(PoE 9W)
• USB / KVM: 1 x USB, Type B
• RS-232 serial port: 1 x 3-pin Phoenix connector
• IR input: 1 x 3.5mm stereo jack
•IR asher: 1 x 3.5mm mono jack
•Firmware update: 1 x USB Micro B
• Accessories: Mounting kit included
• Dimensions (W x D x H ): 190mm x 114mm x 25mm
• Shipping weight (Kit): 0.8kg
• Operating temperature: 32°F to 104°F (0°C to 40°C)
• Storage temperature: -4°F to 140°F (-20°C to 60°C)
XT-4K-VIP-RX
• Video output: 1 x HDMI Type A, female
• Audio output: 2 x RCA L/R analog audio
•Video input/Ethernet port: 1x LAN RJ45 connector (PoE 9W)
•Video/Ethernet extension: 1 x LAN RJ45 connector
• USB / KVM: 2 x USB, Type A
• RS-232 serial port: 1 x 3-pin Phoenix connector
• IR input: 1 x 3.5mm stereo jack
•IR asher: 1 x 3.5mm mono jack
•Firmware update: 1 x USB Micro B
• Accessories: Mounting kit included
• Dimensions (W x D x H ): 190mm x 114mm x 25mm
• Shipping weight (Kit): 0.8kg
• Operating temperature: 32°F to 104°F (0°C to 40°C)
• Storage temperature: -4°F to 140°F (-20°C to 60°C)
Package Contents:
• 1 x XT-4K-VIP-TX/RX
•1 x 3-pin Phoenix connector
Certications
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION - changes or modications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
CANADA, INDUSTRY CANADA (IC) NOTICES
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other household wastes. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please use the return and collection systems or
contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.
• 1 x Mounting kit
• 1 x Quick Reference Guide
Tech Support:
[email protected]
Main:
1 [phone] - US
1 [phone] - International
1 [phone] - Fax
Web:
www.xantech.com
10023196_RevA9_Quick_Reference_Guide_Xantech_XT_4K-VIP_TXRX_0304_PRINT.indd 4 03/04/2019 09:51