Xerox 3150 - Phaser B/W Laser Printer User manual

Guia de conexão em rede
Guía de trabajo en red
Guide réseau
Networking Guide

English : Using the Printer on a Network
About Network Printing ............................................ 2
Installing a Network Card ........................................ 2
Setting an IP Address .............................................. 6
Printing Using the Xerox Printer Port ......................... 7
Français : Utilisation de l’imprimante en
réseau
A propos de l’impression en réseau ........................... 2
Installation d’une carte réseau ................................. 2
Création d’une adresse IP ........................................ 6
Impression à l’aide du port de l’imprimante Xerox ....... 7
Español : Utilización de la impresora en red
Acerca de la impresión en red .................................. 2
Instalación de una tarjeta de red .............................. 2
Configuración de una dirección IP ............................. 6
Impresión a través del puerto de impresora Xerox ...... 7
Português : Utilizar a impressora em rede
Sobre impressão em rede ........................................ 2
Instalar uma Placa de Rede ...................................... 2
Configurar um endereço IP ...................................... 6
Imprimir usando a porta da impressora Xerox ............ 7
Русский : Использование принтера в сети
О сетевой печати ................................................... 2
Установка платы сетевого интерфейса .................... 2
Настройка IP-адреса .............................................. 6
Печать с использованием порта принтера Xerox ....... 7
uUGGwGXGGmSGqGX]SGYWW[GGYa\XGwt

English
This chapter includes:
• About Network Printing
• Installing a Network Card
• Setting an IP Address
• Printing Using the Xerox Printer Port
Using the Printer
on a Network
uUGGwGXGGmSGqGX]SGYWW[GGYa\XGwt

2
Using the Printer on a Network
About Network Printing
The Network Interface Card is an internal print server for
10/100 Base TX networks. You can use your printer in a network
environment by installing this network interface card in an
optional interface slot of the Xerox Phaser 3150 printer.
To connect your printer to the network and use it as the network
printer, you will need to do the followings:
• Set an IP address. See page 6.
• Install the printer driver on each computer connected to the
network using the supplied CD.
• Set the Xerox Network Printer Port. See page 7.
After setting the IP address, install the printer driver using the
supplied CD on each computer connected to the network and set
the Xerox Network Printer Port. To set the Xerox Network Printer
Port, see page 7. Then you can use your printer as the network
printer.
Installing a Network Card
To use your printer on a network, you need to install an optional
network interface card.
1 Turn the printer’s power off and unplug all cables from the
printer.
2 Remove the two screws on the back of the printer.
uUGGwGYGGmSGqGX]SGYWW[GGYa\XGwt

Using the Printer on a Network
3
English
3 Open the control board cover.
4 Remove the two screws and the bracket from the control
board. You can discard the old bracket.
5 Insert the front of the network interface card into the
corresponding slot inside the printer.
uUGGwGZGGmSGqGX]SGYWW[GGYa\XGwt

4
Using the Printer on a Network
6 Make sure that the connector on the card is properly seated
in the connector on the board. Push the card in firmly.
7 Insert and tighten the two supplied screws.
8 Close the control board cover.
uUGGwG[GGmSGqGX]SGYWW[GGYa\XGwt

Using the Printer on a Network
5
English
9 Replace the two screws.
10 Plug one end of an Ethernet cable into the Ethernet network
port on the printer and
the other end of the cable into a
network LAN connection.
To the network LAN connection
uUGGwG\GGmSGqGX]SGYWW[GGYa\XGwt

6
Using the Printer on a Network
Setting an IP Address
Before using your printer on the network, you must set an IP
address, subnet mask, and gateway for the printer. If the
printer's IP address is not set, the printer will use the default IP
address preset at the factory. To use the printer in your network
environment, the printer's IP address must match your
network's addressing method.
Use the SetIP utility to manually configure these settings. If you
want the IP address to be set automatically by a DHCP or BOOTP
server, that server must be installed and actively running on
your network.
N OTES :
• You can use a network interface card test page to see the current
network configuration and MAC address. To print a network
printer card test page, press and hold
the button on the
control panel for 6 seconds until all LEDs blink fast
.
• For information on the additional network settings, see the
infoSMART Knowledge Base at www.xerox.com/support.
You can set your printer’s IP address by using the Set IP
program on your printer’s CD.
Run the Set IP program on a network-connected computer and
set the IP address. To do so:
1 Place the CD-ROM that came with your printer in the
computer’s CD-ROM drive. Installation will start
automatically.
If the CD-ROM driver does not automatically run:
Select
Run from the Start menu, type X:\setup.exe in the
Open box (Where
X is the designated drive letter for the
CD-ROM drive) and click
OK .
2 Select the language you want to view.
3 Click the Browse CD Directory .
4 Double click the Set_IP folder.
5 Double click the language folder you want to view.
6 Double click the Set IP .
The Set IP program opens.
uUGGwG]GGmSGqGX]SGYWW[GGYa\XGwt

Using the Printer on a Network
7
English
7 The Set IP window should automatically show your network
interface card. Double-click the card or click
to open
the
TCP/IP Configuration window.
8 In the TCP/IP Configuration window, enter the MAC
address of the interface card and fill in the TCP/IP parameter
boxes. When you are finished, click
Config .
9 Click Yes to apply your settings.
The configured printer prints out a test page allowing you to
check to see if your settings have been correctly applied.
10 When you are finished, exit the program.
Printing Using the Xerox Printer
Port
After you set the IP address for your printer, you can use the
Xerox Network Printer Port and enable printing on other network
users’ systems to print to the network printer. Follow these
steps:
N OTE : Before setting the network port, you must install the
printer driver on your system if it has not already been installed.
Use the installation software that came with the printer. See the
User’s Guide for details.
1 Click the Start menu.
2 For Windows 98/Me/NT 4.0/2000, select Settings and then
Printers .
For Windows XP, select Printers and Faxes .
3 Select the Xerox Phaser 3150 PCL 6 printer.
4 Click the right mouse button on the printer icon and select
Properties .
uUGGwG^GGmSGqGX]SGYWW[GGYa\XGwt

8
Using the Printer on a Network
5 Click the Details tab for Windows 98/Me.
Click the
Ports tab for Windows NT 4.0/2000/XP.
6 Click Add Port .
7 Click Other and select Xerox Network Printer Port . Click
OK for Windows 98/Me.
Select
Xerox Network Printer Port and click New Port
for Windows NT 4.0/2000/XP.
8 To search through all of the network interface cards
connected to the network, select
Auto Detection on
network
and click Next .
You can find the printer by entering the IP Address.
9 If you selected Auto Detection on the network , the
system detects all of the Phaser 3150 printers connected to
the network, and displays a list. Select the printer you want
to use, then click
Next .
10 Type a port name to identify the new printer and click
Finish .
11 The selected port displays on the print port list. Click OK or
Close .
Now you can print documents using the printer on the
network.
uUGGwG GGmSGqGX]SGYWW[GGYa\XGwt