Xerox 4215 Technical manual

XEROX
Xerox 4219/MRP
Xerox 4215/MRP
Mid Range Systems Printers
Installation Planning Guide
February 1994
720P13290

Xerox Corporation
701 S. Aviation Boulevard
El Segundo, CA 90245
© 1994 by Xerox Corporation. All rights reserved.
Copyright protection claimed includes all forms and matters of
copyrightable material and information now allowed by statutory
or judicial law or hereinafter granted, including without limitation,
material generated from the software programs which are
displayed on the screen, such as icons, screen displays, looks,
etc.
Printed in the United States of America
Xerox® and all Xerox products mentioned in this publication are
trademarks of XEROX CORPORATION. Adobe® and PostScript®
are trademarks of Adobe Systems, Incorporated. AS/400® is a
trademark of International Business Machines Corporation.
CS Triumvirate and CS Triumvirate Condensed are trademarks of
Agfa Corporation. CS Century Schoolbook, CS Courier, CS
Letter Gothic, CS Omega, CS Palacio, CS Times, are licensed to
Xerox Corporation by Agfa Corporation. ITC Avant Garde
Gothic®, ITC Bookman®, ITC Garamond®, ITC Korinna®, ITC New
Baskerville®, ITC Souvenir®, ITC Zapf Chancery® and ITC Zapf
Dingbats® are trademarks licensed to Xerox Corporation by
International Typeface Corporation.
Helvetica®, Palatino®, Times, and Univers® are trademarks of
Linotype-Hell AG and/or its subsidiaries. Monotype Bodoni is a
trademark of the Monotype Corporation plc. Other product
names used herein are trademarks of their respective owners.
Some excerpts from definitions and charts of Adobe Systems
Incorporated and Hewlett-Packard Company have been used
herein.
Changes are periodically made to this document. Changes,
technical inaccuracies, and typographic errors will be corrected in
subsequent editions.
This document was created on the Xerox 6085 Professional
Computer System using VP software. The typeface is Optima.

Notices
Installation caution
The Xerox 4219/MRP and 4215/MRP Mid Range Systems Printers
cannot be installed by customers. Only a Xerox service
representative should install the equipment.
Safety
CAUTION: This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance
with the installation requirements, may cause interference to
radio communications.
U.S.A.
This equipment has been tested and found to comply with the
limits for a Class A digital device pursuant Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. Operation of this equipment in a
residential area is likely to cause harmful interference, in which
case, the user is required to correct the interference at personal
expense.
Canada
This digital apparatus does not exceed the Class A limits for radio
noise emissions from digital apparatus as set out in the radio
interference regulations of the Canadian department of
communications.
Les present appareil numerique n’emet pas de bruits
radioelectriques depassant les limites applicables aux appareils de
Classe A prescitees dans le reglement sur le brouillage
radioelectrique edicte par les ministre des communications du
Canada.
Europe: 50 Hz, 220 to 240 V equipment
This equipment has been tested and certified in conformance
with European commission directive 82/499/ECC and VDE
0871/0875, Class A, relating to radio frequency interference.
XEROX 4219/MRP AND 4215/MRP INSTALLATION PLANNING GUIDE iii

NOTICES
Laser safety
The 4219/MRP and 4215/MRP comply with appropriate safety
standards.
Specifically regarding lasers, the equipment complies with laser
product performance standards set by governmental,
international and national agencies as a Class 1 laser product. It
does not emit hazardous light; the beam is totally enclosed
during all phases of customer operation and maintenance.
WARNING: Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
Warning labels
There are several user accessible Laser Safety Warning labels
located on the printer. An example is shown below.
iv XEROX 4219/MRP AND 4215/MRP SYSTEMS INSTALLATION PLANNING GUIDE

NOTICES
These laser warning labels are placed on panels that cover areas
that are not operator serviceable. These panels are not to be
removed.
Operational safety
Your Xerox equipment and supplies are designed and tested to
meet strict safety requirements. These include safety agency
examination, approval, and compliance with established
environmental standards.
Attention to the following notes ensures the continued safe
operation of your equipment.
Do this
Always connect equipment to a properly grounded power source
receptacle. If in doubt, have the receptacle checked by a
qualified electrician.
WARNING: Improper connection of the equipment grounding
conductor can result in electrical shock.
Always place equipment on a floor or table with adequate
strength for the weight of the machine.
Always have at least two people move or relocate the
equipment.
Always use materials and supplies specifically designed for your
Xerox equipment.
WARNING: Use of unsuitable materials may result in poor
performance and can possibly create a hazardous condition.
Do not do this
Never attempt any maintenance function that is not specifically
described in this document.
Never remove any covers or guards that are fastened with screws
unless otherwise instructed. You cannot service areas within
these covers.
Never override or “cheat” electrical or mechanical devices.
Never operate the equipment if you notice unusual noises or
odors. Disconnect the power cord from the power source
receptacle and call Xerox service to correct the problem.
U.S. only: If you need any additional safety information
concerning the equipment or Xerox supplied materials, call the
following toll-free number: 1-800-828-6571.
Approvals and certification
60 Hz, 115 V Listed by Underwriters Laboratories, UL1950 (UL). Meets CSA
standards, C22.2 NO 950 (CSA).
50 Hz, 220 to 240 V Meets the British Standards Institution, IEC950 (BSI).
XEROX 4219/MRP AND 4215/MRP INSTALLATION PLANNING GUIDE v

Table of contents
Notices iii
Installation caution iii
Safety iii
Laser safety iv
Operational safety v
Introduction ix
About this guide ix
Contents ix
Conventions x
Related publications x
Xerox 4219/MRP and 4215/MRP library x
PostScript and PCL references xi
1. Overview 1-1
Standard features 1-1
Coax interface features 1-3
Twinax interface features 1-4
Optional features 1-4
Printer components 1-5
2. Installation planning tasks 2-1
Xerox responsibilities 2-1
Your responsibilities 2-2
Installation countdown log 2-3
3. Preinstallation 3-1
Delivery requirements 3-1
4219/MRP 4215/MRP dimensions 3-1
Space requirements 3-2
Electrical requirements 3-2
Operating environment 3-3
Noise level 3-3
Special configurations 3-3
Coax interface configurations 3-4
Twinax interface configurations 3-4
Non-printable area 3-6
XEROX 4219/MRP AND 4215/MRP INSTALLATION PLANNING GUIDE vii

TABLE OF CONTENTS
4. Connectivity 4-1
Coax environment 4-1
Twinax environment 4-2
PC direct connect environment 4-3
5. Preparing the installation checklists 5-1
Completing Checklist 3: General setup 5-1
Completing Checklist 4: Setup Printer—PCL 5 Setup 5-2
Completing Checklist 5: Setup Printer— PostScript Resolution,
Print Enhancement, Communications Priority, Panel Security 5-3
Completing Checklist 6: Parallel, Serial, Other I/O 5-4
Appendices A. Ordering fonts, options, and supplies A-1
B. Interface support B-1
C. Checklists C-1
Glossary GLOSSARY-1
Index INDEX-1
viii XEROX 4219/MRP 4215/MRP INSTALLATION PLANNING GUIDE

Introduction
This guide helps you prepare for the installation of the Xerox
4219/MRP and 4215/MRP Mid Range Systems Printers.
Information is provided on each 4219/MRP and 4215/MRP
component and its installation requirements.
About this guide
This guide directs the site planner in preinstallation procedures,
as well as ongoing activities after the printer has been installed.
Contents
This guide contains the following chapters:
Chapter 1 “Overview” presents a general overview of the printer and its
components.
Chapter 2 “Installation planning tasks” discusses preinstallation and
installation planning tasks. It identifies areas of responsibility and
the assignment of tasks. An installation countdown log is
included.
Chapter 3 “Preinstallation” explains tasks that must be performed prior to
installation to prepare the site. Electrical and environmental
specifications are included in this chapter.
Chapter 4 “Connectivity” gives an overview of the connectivity possibilities
by environment.
Chapter 5 “Preparing the installation checklists” guides you through the
options listed on the installation checklists which you must
complete prior to installation day.
Appendix A “Ordering fonts, options, and supplies” describes how to order
fonts, describes the available printer options, and explains how
to obtain Xerox service and supplies. A complete supplies and
accessories list is included.
Appendix B “Interface support” discusses the interface support available for
the printer.
Appendix C “Checklists” contains configuration checklists that help your
Xerox service representative configure your 4219/MRP or
4215/MRP on installation day.
A glossary is also included at the end of this guide.
XEROX 4219/MRP AND 4215/MRP INSTALLATION PLANNING GUIDE ix

INTRODUCTION
Conventions
This guide uses the following conventions throughout.
italics Italics are used for document and library names (for example, the
Xerox Coax Command Reference).
WARNING: Warnings are associated with the safety of people.