XFit MOUNTAIN User manual

Speeding Bike
User’s Manual
The specifications of this product may vary from this photo and are
subject to change without notice.

1

2
IMPORTANT SAFETY NOTICE
Note the following precautions before assembling and operating the
machine.
1. Once fully assembled, please check that all hardware parts such as
bolts, nuts and washers are positioned and secured firmly.
2. Please check regularly that the safety chain guard that protects the
moving parts of the machine is secured and in good order.
3. Please always check the seat post, seat slider, pedals and handlebar
are secured firmly before getting on the bike.
4. To lubricate all moving parts annually is recommended.
5. Do not wear loose clothing to avoid entangling in any moving parts.
6. Do not remove feet from the pedals while they are in motion.
7. Always wear shoes when using the machine.
8. Dry the bike after each use to remove sweat and moisture. Wipe the
machine with a damp cloth, water and mild soap. Do not use a
petroleum-based solvent to clean the machine in order not to damage
the finish.
9. Please keep children away from the bike while it is in use. Do not allow
children to use the bike. This bike is designed for adults, not children.
10. Do not dismount the bike until the pedals have stopped completely.
11. Stop exercise immediately in case of nausea, shortness of breath, faint,
headache, pain, tightness in your chest or any discomfort.
12. Do not place fingers or any other objects into the moving parts of the
bike.
13. Prior to any exercise, consult with your physician first to establish the
exercise frequency, time and intensity appropriate for your particular age
and condition.
14. After exercising, please pull down the tension controller to increase
resistance so that the pedals will not rotate freely and possibly hurt
someone.

3
EXPLOSIVE DIAGRAM

4
PARTS LIST
Part
No.
Description Qty
Part
No.
Description Qty
1 Main frame 1 18
Hex nut
M10
4
2
Front
stabilizer
1 19
Computer
bracket
1
3 Rear
stabilizer 1 20
Water
bottle
holder
1
4 Handlebar 1 21 Foam grip 2
5 Seat post 1 22 Cap 2
6 Seat slider 1 23 Allen bolt 4
7 Saddle 1 24
Spring
washer
4
8 Pop-pin
knob 3 25 A/B
Handleba
r cover
1
p
r
9L/
R
Pedal 1pr 26
Handleba
r post
1
10L/
R
Crank 1pr 27
Phillips
screw
4
11 Leveler feet 4 28 Allen bolt 2
12 Square cap 4 29 roller 2
13 Flat washer 10 30 Nylon nut 2
14 Allen bolt 4 31 Computer 1
15 Plastic
bushing 3 32
Phillips
tapping
screw
2
16 Square cap 1 33
Flat
washer
2
17 Sensor wire 1 34
Water
bottle
1

5
All Hardware is attached to the bike.
NOTE:
Most of the listed assembly hardware has been packaged separately, but
some hardware items have been preinstalled in the identified assembly
parts. In these instances, simply remove and reinstall the hardware as
assembly is required.
Please reference the individual assembly steps and make note of all
preinstalled hardware.
Prior to assembly of this product, remove all components from the package
and verify all the listed parts are supplied. Once certain, begin with the first
assembly step
ASSEMBLY INSTRUCTIONS
Note: Assembly requires 2 people.
Step A:
Install the Front stabilizer (2) and Rear stabilizer (3) to the Main frame
(1) with the Bolts (14) and Flat washers (13).
Note: The Leveler feet （11）under the stabilizers can be adjusted to
keep the equipment stable.

6
Step B:
Attach the Handlebar (4) to the Handlebar post (26), secured with Allen
bolts (23) , Spring washers (24) ,Computer bracket (19) and Flat
washer（13）.
Slide the Lower cover (25B) to the Handlebar post（26）, use Phillips
screw (27) to fit the Upper cover (25A) between handlebar(4) and
handlebar post(26), Turn and loosen the Knob (8), pull the pin, and
then insert the handlebar post(26) into the Main frame(1)
simultaneously. Make sure the pin settles into the desired hole and
then secure the Knob.

7
Step C:
Fix Saddle (7) to Seat slider (6) with multifunctional wrench tightly .
Adjust the Seat slider (6) to a proper position and then lock it on Seat
post (5) with Pop-pin knob (8).
Insert Seat post (5) to Main frame(1) in a proper high position and then
tighten with Pop-pin knob (8).
Note: The position of saddle is Horizontal & Vertical adjustable by the
both Knob (8).

8
Step D:
Attach the Pedals (9L/R) to the Cranks (10L/R) respectively, viewed
from the rider’s seated position.
Note: Both pedals are labeled L FOR LEFT and R FOR RIGHT. Turn
the left pedal COUNTERCLOCKWISE and the right pedal
CLOCKWISE. Before exercising, the paddle should be tighten or the
thread of paddle will be damaged easily.

9
Step E:
Insert sensor wire (17) to Computer (31), then insert Computer (31) to
computer bracket (19).
Attach the Water bottle holder (20) to the main frame(1) with the
Screws (32) and Flat washer (33) and then put on t Water bottle (34).

10

11

12
TERMS OF WARRANTY
•Warranty period is 2 years for mechanical, electrical / electronic parts and 5 years for the
metal frame.
•X-TREME STORES S.A. undertakes to repair the machine free of charge in the event of
damage due solely to a manufacturing fault. The warranty covers the cost of the spare
parts. Replacement of spare parts or not is up to the company technicians. The customer
is responsible for the control and adjustment of the machine.
•This warranty note is only valid if it is accompanied by legal proof of purchase (invoice or
retail receipt). The warranty period is not extended for any reason and the transfer of it to
a third party is excluded.
•Any damage is repaired as soon as possible and any claim for damages due to lack of
spare parts and delay in repairing the damage is excluded. The costs of transporting the
machine to or from the dealership will be borne by the customer after 6 months of
purchase.
•The warranty conditions are set by the manufacturers of machinery and are governed by
European regulations.
•Upon expiry of the warranty, any replacement part is covered by a 6-month warranty.
THE WARRANTY SHALL NOT APPLY:
•When the machine is used for any purpose other than home use (gyms, clubs, institutes,
hotels, studios, etc.).
•When the fault is the result of misuse, alterations, poor connection, poor maintenance,
voltage fluctuations in the PPC network.
•Components damaged by user fault such as broken plastic parts, damaged belt with
improper adjustment, incorrect or incomplete lubrication, damage when moving the
machine.
•When the machine is opened or repaired by third parties.
•When the damage is caused by the buyer's negligence & the instructions for use have
not been followed.
•When the machine is outdoors or exposed to sun or dust.
•When electronic components (console) are damaged by intense sweating or other liquid
that has come into contact with or penetrated inside them.
Tel.: [phone] – Fax: [phone] –e-mail: [e-mail]

13
CAUTION! The company does not have no responsibility for causing
damage due to misuse of the product and non-compliance with the
instructions for use.
THE WARRANTY IS NOT VALID IF: The machine is placed outdoors or
exposed to sun and dust
CAUTION! During exercise, heavy sweating can cause mechanical and
electrical damage to the machine. Like any other liquid substance, sweat is
capable of causing damage mainly to the electrical parts of the machine (dial,
cables, etc.). The best solution is to use a towel during exercise and wipe the
machine after each use to avoid any unwanted damage.
Check and tighten the screws at regular intervals, as they may loosen
due to vibrations. Damage that may be caused by a lack of
maintenance is not covered by the warranty.

14

15
34 koupi Avenue, Koropi
P.C.:19441 - P.O. Box 6201
Tel.: [phone] - Fax: [phone]
E-mail: [e-mail] • f/xtrstores • /@xtr.gr
Tel. for all of Greece:
801.11.15.100
www.xtr.gr