XFit LEGEND User manual

Treadmill
User’s Manual
* Product specifications may differ from the photo and are subject to change without notice.

- 1 -

- 2 -
WARNING
Read all instructions carefully before using this product. Retain this owner’s manual for future
reference:
----When using this treadmill, keep attaching the safety pull pin rope to your clothes.
----When you are running, keep your hand swinging natural, stare frontward, never look down at
your feet.
----Add the speed step by step when running.
----When emergency happens, take away the “emergent stop button” immediately.
----Leave the treadmill after the running belt stop stably.
Caution: Read the assembly instruction carefully, follow the instruction when assemble.
ATTENTION
01- Before starting any exercise program, consult with your physician or health professional.
02- Check all the bolts locked.
03- Never put the treadmill in the wetness area, or it will cause troubles.
04- We take no responsibility for any troubles or hurts due to above reasons.
05- Dress sport clothes and shoes before running.
06- Do not do exercise in 40 minutes after meal.
07- To prevent hurts, please warm up before exercise.
08- Consult with doctor before exercise if you have high blood pressure.
09- The treadmill is only used for adults.
10- Provide the olds, children and handicapped with good care, guide, and supervision.
11- Do not plug anything into any parts of this equipment, or it may damage.
12- Do not connect line to the middle of cable; do not lengthen cable or change the cable plug; do
not put any heavy thing on cable or put the cable near the heat source; forbid using socket with
several holes, these may cause fire or people may be hurt by the power.
13- Cut off the power when the equipment is not used. When the power is cut off, do not pull the
power line to keep the wire unbroken.
14- Maximum weight of user: 130 kgs.
15- Pulse monitor data may not be accurate, cannot be used for medicine. Over-exercise may
cause injury, even death. If you have a feeling of dizziness, sickness, or other abnormal symptoms,
please stop training, and consult a doctor immediately.
CAUTION! The company does not have no responsibility for causing damage due to misuse of the
product and non-compliance with the instructions for use.

- 3 -
IMPORTANT SAFETY PRECAUTIONS
1. Plug the power cord of the treadmill directly into a dedicated grounded circuit. This product must
be grounded. If it has breakdown, grounding provides a path of least resistance for electric current
to reduce the risk of electric shock.
2. Position the treadmill on a clear, level surface. Do not place the treadmill on thick carpet as it may
interfere with proper ventilation. Do not place the treadmill near water or outdoors.
3. Position treadmill so that the wall plug is visible and accessible.
4. Never start the treadmill while you are standing on the walking belt. After turning the power on
and adjusting the speed control there may be a pause before the walking belt begins to move,
always stand on the foot rails on the sides of the frame until the belt is moving.
5. Wear appropriate clothing when exercising on the treadmill. Do not wear long, loose fitting
clothing that may be caught in the treadmill. Always wear running or aerobic shoes with rubber
soles.
6. Make sure the power supply is connected and the safety lock is effective before using the
treadmill. Fit one side of the safety lock on the treadmill and clip the other side on your clothes or
belt, which will enable you to pull off the safety lock promptly in an emergency.
7. Always unplug the power cord before remove the treadmill motor cover.
8. Make sure there is no less than 2*1m space behind the treadmill.
9. Keep small children away from the treadmill during operation.
10. Always hold the handrails when initially walking or running on the treadmill, until you are
comfortable with the use of the treadmill.
10. Always attach the safety pull pin rope to your clothing when using the treadmill. If the treadmill
should suddenly increase in speed due to an electronics failure or the speed being inadvertently
increased, the treadmill will come to a sudden stop when the pull pin is disengaged from the
console.
12. In case of any abnormality during the use process, please remove the safety lock immediately,
grasping the handlebar and jumping onto the two edgings, then get off the treadmill after it stops.
13. When the treadmill is not being used, the power cord should be unplugged, and the safety pull
pin removed.
14. Put the safety key away where cannot be reached by the children. Minors must be accompanied
by the adults when using the treadmill.
15. Before starting any exercise program, consult with your physician or health professional. He or
she can help establish the exercise frequency, intensity (target heart zone) and time appropriate for
your age and condition. If you have any pain or tightness in your chest, an irregular heartbeat,
shortness of breath, feel faint or have any discomfort while you exercise, STOP! Consult your
physician before continuing.

- 4 -
16. If you observe any damage or wear on the mains plug or on any section of the mains lead then
please have these replaced immediately by a qualified electrician – do not attempt to change or
repair these yourself.
17. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
18. Put your feet on the side rail before using the treadmill, and always attach the safety pull pin
rope to your clothing. Hold the handlebar before the running belt moving well (feel the running
speed by your single foot before using it). To avoid loss balance, please slow down the speed to the
lowest or take off the safety. And hold the handlebar to jump to the side rail when emergency or the
safety key is not attached.
19. Make sure the treadmill has stopped before folding. Please don’t operate it after folding the
treadmill.

- 5 -
ASSEMBLY STEPS
Note: Assembly requires 2 people.
STEP 1:
Open the package, take out all parts and place the main frame on the flat ground.
(NOTE: please don’t cut down the packing straps right now.)

- 6 -
STEP 2:
1. Cut down the straps when the main frame was placed well. (NOTE: Don’t move it anymore.)
2. Connect the Controller wire（97）and Extension lower wire (96).
3. Lock the upright tube (3) on the bottom frame (1) with the hex socket screws (59) and the Lock
washer (84).
NOTE: please don’t tighten the Hex socket screw (59) for the time being.

- 7 -
STEP 3:
1. Connect the extension upper wire (95) and the extension lower wire (96)
2. Lock the computer frame (4) on the upright tube (3) with the hex socket screw (59) and Lock washer
(84) lock the hex socket screw (59) tightly which connect the bottom frame (1) and upright tube (3).

- 8 -
STEP 4:
1. Lock the Protective cover (37L /R) tightly to the Bottom frame （1）with Cross tapping screw (79).
2. Insert the A side of the Outside upright cover (35) and inside upright cover (36) to the B side of the
computer frame (4) as the picture shown, then lock the Outside upright cover (35) and inside
upright cover (36) tightly to the Upright tube (3) with Cross tapping screw (79).

- 9 -
STEP 5:
When you fold the machine:
Put your hands on place A, lift up the machine in the direction of the arrow until you hear the sound from
the cylinder (10).

- 10 -
STEP 6:
When you unfold the machine:
Grasp the place A by one hand, kick the place B of cylinder (10) with your right foot, pull the running
board to the level of place C, then the running board will get down automatically.

- 11 -
GROUNDING METHODS
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of
least resistance for electric current to reduce the risk of electric shock.
This product is equipped with a cord having an equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
DANGER – Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify the plug provided with the product – if it will not fit the
outlet, have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 220-volt circuit and has a grounding plug that looks like the
plug illustrated in sketch A in following figure. Make sure that the product is connected to an outlet
having the same configuration as the plug.
No adapter should be used with this product.
Grounding Methods
SPECIFICATIONS
Dimensions (open) L: 195 x W: 87 x H: 150.5cm Display 7” LCD
(blue backlight)
Dimensions (closed) L: 135 x W: 87 x H: 154cm Motor DC 3 hp (peak 4.5 hp)
Belt surface W: 50 x L: 141cm Programs P1-P18+U1-U3+Bodyfat
Belt thickness 1.6 mm Anti-vibration
system
Air-spring – Double
anti-vibration protection with 6
elastomeric points
Net weight 100 kg Speed range 1.0-20 km/h
Maximum user weight 130 kg Incline 0-15%
Console Built-in speakers, MP3 Folding system Easy lift system
Certification CE-ROHS-EN957
Grounded pins
Grounded Outlet

- 12 -
OPERATION INSTRUCTIONS
1. Function specifications
IDescription to windows and keys
1. LCD windows will display the following functions:
A. Speed window: display speed data.
B. Time/ heart rate window: display time/ heart rate data. Display heartbeat in the operation
process first.
C. Distance/ calorie/ incline windows: display distance/ calorie/ incline data. Display in turn in
operation process. Press "Mode” to switch the display. Incline will be displayed first for
section change; incline will be displayed first for stop; if the incline is 0, the value displayed is
the distance.
2. Function keys: START, STOP, PROGRAM, MODE, SPEED +, SPEED -, INCLINE +, INCLINE -,
SPEED SHORTCUT （3、6、9、12、15) KMH/MPH, INCLINE SHORTCUT (3、6、9、12、15);
3. Description to function keys:
A. Program: in the stop state, press it to select programs in turn: manual mode -P01
-P02- ...-P18 -U01 -U02 -U03-FAT

- 13 -
B. MODE: in the stop state, press it to select programs in turn: manual mode (normal state) -
time countdown- distance countdown – calorie countdown.
C. START: in the stop state, press it to start up the motor.
D. STOP: when the motor is running, press it to stop the motor.
E. SPEED +: in setting sate, press it to increase the set value. When the motor is running,
press it to increase the speed.
F. SPEED -: in setting sate, press it to decrease the set value. When the motor is running,
press it to decrease the speed.
G. INCLINE +: in setting sate, press it to increase the set value. When the motor is running,
press it to increase the incline.
H. INCLINE -: in setting sate, press it to decrease the set value. When the motor is running,
press it to decrease the incline.
I. When the safety lock is removed, press PROGRAM+MODE for 3s to for metric –inch
conversion.
II Instructions to fixed program/ startup
1. Program:
A. One manual mode, including normal mode, time countdown, calorie countdown and
distance countdown modes.
B. 18 fixed programs: P01, P02… P18.
C. 3 customized programs: U01, U02 and U03.
2. Startup
A. Past the safety lock to the safety lock switch position on the panel.
B. Press “START” and the window will display 3—2—1; for each time of number reduction, the
buzzer will sound. Then, the motor will be started.
III Manual mode:
1. How to enter manual mode:
A. Switch on the power supply; then, directly enter normal mode under the manual mode.
B. In stop state, press MODE to select normal mode under the manual mode.
2. Three setting functions under manual mode: time setting, distance setting and calorie setting.
A. When entering the manual mode, the time is displayed as 0:00.
B. In manual mode, press MODE to enter time countdown mode; the time window will display
the time and flicker; the initial time is 30:00; set countdown time by SPEED +/ SPEED - and
INCLINE +/ INCLINE -. Time setting range: 5:00-99:00.
C. In time countdown mode, press MODE to enter distance countdown mode; the initial
distance will be displayed as 1.00 km/mi; set the distance by SPEED +/ SPEED - and
INCLINE +/ INCLINE - in the range of 0.50-99.90 km/mi; each time of increase/ decrease will
be 0.1 km/mi.
D. In distance countdown mode, press MODE to enter calorie countdown mode; the initial
distance will be displayed as 50.0kcal; set the calorie by SPEED +/ SPEED - and INCLINE
+/ INCLINE - in the range of 10.0-999.0 kcal; each time of increase/ decrease will be 1.0kcal.
3. Operation in manual mode:
A. Press START and the motor will start operating after 3s of countdown; the initial speed will
be 1.0km/h for metric system or 0.6mile/h for imperial system.
B. Press SPEED +/ SPEED - to adjust speed.
C. Press INCLINE +/ INCLINE - to adjust the incline.
D. Press speed shortcuts to quickly set up to the speed marked on the key.
E. Press incline shortcuts to quickly set up to the incline marked on the key.

- 14 -
F. When the motor is running, press STOP to stop the motor.
G. Remove the safety lock to urgently stop motor running; then, LCD window will display “---”
and the buzzer will make short sound of Bi-Bi-Bi.
H. When the set time reduces to zero or when the set calorie reduces to zero, or the set
distance reduces to zero, the buzzer will make short alarm “Bi-Bi-Bi”, the speed window will
display END; 5s later, the machine will return to the standby state and the buzzer will make
long alarm “Bi-Bi”;
I. Parameters not set will increase forwards and will be reset after reaching the upper limit of
the display range; in manual mode, the machine will stop when the time accumulates to be
more than 99: 59 (100min).
IV Fixed program mode:
1. The initial time is set to be 30min; only time can be set; setting range: 5:00- 99:00. Press SPEED
+/ SPEED - or INCLINE +/ INCLINE - to adjust the set value.
2. Press START key, the motor will start running and the speed will gradually increase to the value
for the first section of auto program (see details in the table of program parameters).
3. Press SPEED +/ SPEED - to adjust speed.
4. Press INCLINE +/ INCLINE - to adjust the incline.
5. Press speed shortcuts to quickly set up to the speed marked on the key.
6. Press incline shortcut to quickly set up to the incline marked on the key.
7. Each program is divided into 20 sections; operating time for each section will be 1/20 of the set
time.
8. The buzzer will sound for three times when switching from one section to another.
9. When the set time reduces to zero, the speed will gradually reduce till the stop of the machine.
The buzzer will make short alarm Bi-Bi-Bi; when the machine stops, the buzzer will make long
alarm of Bi-Bi-Bi. The speed window will display END; 5s later, the machine will return to the
standby state; then, the buzzer will make long-alarm of Bi-Bi.
10. Remove the safety lock to urgently stop motor running; then, LCD window will display “---” and
the buzzer will make short sound of Bi-Bi-Bi.

- 15 -
VParameters in fixed program mode (metric system)
No.
Setup time /20 = Each segment of the running time
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
P01
SPEED
2
3
3
4
5
3
4
5
5
3
4
5
4
4
4
2
3
3
5
3
INCLINE
1
1
2
2
2
3
3
3
2
2
1
2
2
1
1
3
3
2
2
2
P02
SPEED
2
4
4
5
6
4
6
6
6
4
5
6
4
4
4
2
2
5
4
2
INCLINE
1
2
2
2
2
3
3
2
2
2
2
2
3
3
3
4
4
3
2
2
P03
SPEED
1
3
3
5
5
3
6
6
6
3
6
6
3
3
3
1
3
4
2
1
INCLINE
1
2
2
1
1
2
2
2
1
1
1
1
3
3
3
5
5
2
1
1
P04
SPEED
3
5
5
6
7
7
5
7
7
8
8
5
9
5
5
6
6
4
4
3
INCLINE
2
3
3
2
2
3
3
3
2
2
2
2
4
4
4
6
6
3
2
2
P05
SPEED
2
4
4
5
6
7
7
5
6
7
8
8
5
4
3
3
6
5
4
2
INCLINE
3
3
3
4
4
5
5
5
4
4
4
4
5
5
3
3
3
2
2
2
P06
SPEED
2
4
4
4
5
6
8
8
6
7
8
8
6
4
4
2
5
4
3
2
INCLINE
3
5
5
5
4
4
4
3
3
3
3
4
4
4
3
3
3
4
3
2
P07
SPEED
2
3
3
3
4
5
3
4
5
3
4
5
3
3
3
6
6
5
3
3
INCLINE
4
4
4
4
3
3
6
6
6
7
7
8
8
9
9
6
6
5
4
4
P08
SPEED
2
3
3
6
7
7
4
6
7
4
6
7
4
4
4
2
3
4
4
2
INCLINE
4
5
5
5
6
6
6
7
8
9
9
9
10
10
10
12
12
8
6
3
P09
SPEED
2
4
4
7
7
4
7
8
4
8
9
9
4
4
4
5
6
3
3
2
INCLINE
5
5
5
6
6
6
4
4
6
6
5
5
8
8
9
9
9
7
4
2
P10
SPEED
2
4
5
6
7
5
4
6
8
8
6
6
5
4
4
2
4
4
3
3
INCLINE
5
6
6
6
7
5
8
8
4
4
4
5
5
8
8
10
10
8
6
3
P11
SPEED
2
5
8
10
7
7
10
10
7
7
10
10
5
5
9
9
5
5
4
3
INCLINE
4
5
3
2
6
6
2
2
2
2
2
4
5
6
3
2
5
5
2
0
P12
SPEED
3
4
9
9
5
9
5
8
5
9
7
5
5
7
9
9
5
7
6
3
INCLINE
1
2
3
2
3
5
5
0
0
2
3
5
7
3
3
5
6
5
3
3
P13
SPEED
3
3
4
4
5
5
6
6
7
7
8
8
9
6
5
5
4
4
3
3
INCLINE
1
1
3
3
5
5
7
7
9
9
11
11
9
3
5
5
3
3
1
1
P14
SPEED
3
4
5
6
7
6
5
4
7
9
9
7
6
9
8
7
6
5
4
3
INCLINE
0
3
3
5
5
7
7
9
9
7
7
5
5
7
7
5
5
3
3
0
P15
SPEED
9
9
9
8
8
8
7
7
7
6
6
6
5
7
8
8
8
9
9
9
INCLINE
0
1
2
1
2
3
3
2
1
2
2
2
0
2
3
2
3
3
2
0
P16
SPEED
8
8
9
9
10
10
12
12
12
12
12
12
11
12
10
10
9
9
8
8
INCLINE
0
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
0
P17
SPEED
1
2
3
4
5
6
7
8
9
10
11
12
11
2
3
4
5
6
5
4
INCLINE
0
0
0
0
3
3
0
0
0
3
3
0
0
0
3
3
0
0
0
0
P18
SPEED
6
6
6
4
4
4
8
8
8
10
10
10
8
6
8
8
8
6
6
6
INCLINE
0
1
1
2
2
2
0
0
0
1
1
1
0
0
1
1
1
0
0
0
VI Customized program:
In addition to 18 built-in programs, the treadmill also has 3 customized programs to support the
customized setting based on the user’s specific situation: U01, U02 and U03.

- 16 -
1、Setting of customized programs:
In standby state, continuous press PROGRAM to the required customized program (U01~ U03);
press MODE to confirm entering the setting; then, set up parameters in the first time section; set up
speed by SPEED +/ SPEED - or speed shortcuts and set up incline by INCLINE +/ INCLINE - or
incline shortcuts; press MODE to complete the first time section’s setting and enter the state to set
up parameters for the second time section until the completion of setting for all the 20 time sections.
Set parameters will be permanently saved until the next time setting. These parameters will not be
lost due to power disconnection.
2、Start of customized program:
A. In standby state, continuous press PROGRAM to the required customized program (U01~
U03). After setting up the operation time, press START.
B. In the customized program state and after the setting of operation time, press START to
immediately start up the machine.
3、Instructions to the setting of customized program:
Each program divides its operation time into 20 sections. Be sure to complete the setting for
speed, incline and operation time for all the 20 sections before pressing START to start the
treadmill.
VII Parameter display range:
Initial Initial setting
value Setting range
Display range
Time (m: s) 0:00 30:00 5:00-99:00 0:00-99:59
Speed in metric system
(km/h)
Speed in imperial system
(mi/h)
0.0
N/A N/A 1.0—20.0KMH
0.6-12.0MPH
Incline 00 N/A N/A 0-15
Distance (km/mi)
0.0
1.00
0.50—99.90
0.00—99.99
Calorie (kcal)
0
50.0
10.0—999.0
0.0—999.9
VIII Safety lock function
Remove safety lock under any situation, LCD window will display “---” and the buzzer will make short
sound of “Bi-Bi-Bi”. If the motor is running, it will be emergently stopped. When the safety lock is
removed, all keys will lose effect.
IMPORTANT: The SAFETY KEY has a magnet which is connected to the console. At the other end
there is a clip that must be placed on your clothes. The treadmill only works with the safety key on
the console.
IX Energy-saving mode:
The system has energy-saving function. In standby state, if no key order input in 10m, the system
will enter the energy-saving mode with the display automatically closed. Press any key to revoke the
system.
XMP3 function (optimal):
When connecting to MP3 or other audio devices in powering on state, the electronic meter can play
music. Sound volume shall be controlled through the audio device; please properly adjust the
volume to obtain better sound quality and avoid impact to built-in audio circuit.

- 17 -
XI USB function (optimal):
When connecting to USB in powering on state, the electronic meter can automatically play MP3
format music. Sound volume can be controlled through keys on the panel; please properly adjust the
volume to obtain better sound quality and avoid impact to built-in audio circuit.
XII Shutdown:
Be sure to shut down the treadmill by switching off the power supply to avoid damage to the
treadmill.
XIII Cautions:
1. Please check whether power supply is connected and whether safety lock is effective before
using the treadmill.
2. In case of any abnormality in the use process, please remove the safety lock and the treadmill
will rapidly slow down till stop; then, restore the safety lock, the equipment will reset and wait for
inputting instructions.
3. In case of any problem of the machine, please contact the dealer; equipment damage may be
caused for non-professional personnel to dismantle or repair the machine.
XVI Calorie calculation method:
70.3×V(Km/h) ×t(h)× (1+? %)
When the lifting is 0, the calorie consumption for each 1km of running is about 70.3kcal.
Check and tighten the screws at regular intervals, as they may loosen due to vibrations. Damage that
may be caused by a lack of maintenance is not covered by the warranty.
THE WARRANTY IS NOT VALID IF: The machine is placed outdoors or exposed to sun and dust.
Dust and fluff enter the internal mechanical parts of the machine, causing serious damage. Keep
the machine free of dust and fluff.
CAUTION! The heart rate sensor and calorie counter are not medical devices. Several factors can affect the
accuracy of the indications. The heart rate sensor is only intended as an aid during exercise to monitor your
heart rate in general.

- 18 -
EXERCISE INSTRUCTIONS
1. The Warmup Phase
This stage helps get the blood flowing around the body and the muscles working properly. It will
also reduce the risk of cramp and muscle injury. It is advisable to do a few stretching exercises
as shown below. Each stretch should be held for approximately 30 seconds, do not force or jerk
your muscles into a stretch - if it hurts, S T O P.
2. The Exercise Phase
This is the stage where you put the effort in. After regular use, the muscles in your legs will become
Stronger. Work to your but it is very important to maintain a steady tempo throughout. The rate of
work should be sufficient to raise your heartbeat into the target zone shown on the graph below. This
stage should last for a minimum of 12 minutes though most people start at about 15-20 minutes.
3. The Cool Down Phase
This stage is to let your Cardio-vascular System and muscles wind down. This is a repeat of the
warmup exercise e.g., reduce your tempo, continue for approximately 5 minutes. The stretching
exercises should now be repeated, again remembering not to force or jerk your muscles into the
stretch. As you get fitter you may need to train longer and harder. It is advisable to train at least
three times a week, and if possible, space your workouts evenly throughout the week. To tone
muscle while on your Treadmill you will need to have the resistance set quite high. This will put
more strain on our leg muscles and may mean you cannot train for as long as you would like. If
you are also trying to improve your fitness, you need to alter your training program. You should
train as normal during the warmup and cool down phases, but towards the end of the exercise
phase you should increase resistance, making your legs work harder than normal. You may have
to reduce your speed to keep your heart rate in the target zone. The important factor here is the
amount of effort you put in. The harder and longer you work the more calories you will burn.
Effectively this is the same as if you were training to improve your fitness, the difference is the
goal.

- 19 -
MAINTENANCE INSTRUCTIONS
WALKING BELT CENTERING AND TENSION ADJUSTMENT
DO NOT OVERTIGHTEN the walking belt. This may cause reduced motor performance and excessive
roller wear.
TO CENTER WALKING BELT:
● Place treadmill on a level surface
● Run treadmill at approximately 3.5 mph
● If the belt offs the track to the right side, please screw the right adjusting bolt clockwise slowly, noticing
the change of the deviating distance, until center the belt. (Attention: the space between the belt and the
right/left edgings is at a distance normally. And the gap between the right and left distance should be no
more than 5mm.
●If the belt offs the track to the left side, please screw the left adjusting bolt clockwise slowly, noticing
the change of the deviating distance, until center the belt. (Attention: the space between the belt and the
right/left edgings is at a distance normally. And the gap between the right and left distance should be no
more than 5mm.
Picture A: If the belt has drifted to the RIGHT Picture B: If the belt has drifted to the L EF T.
TENSIONING THE BELT
If you can feel a slipping sensation when running on the treadmill, the running belt must be
tightened. In most cases, the belt has stretched from use, causing the belt to slip. This is a normal
and common adjustment. To eliminate this slipping, tension both the rear roller bolts with the
appropriate size Allen wrench, turning it 1/4 TURN to the right as shown. Try the treadmill again to
check for slipping.
Repeat, if necessary, but NEVER TURN the roller bolts more than 1/4 turn at a time. The belt
tension is set properly when the running belt is 50 - 75mm from the deck.
WARNING: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET BEFORE
CLEANING OR SERVICING THE UNIT.
CAUTION! During exercise, heavy sweating can cause mechanical and electrical damage to the
machine. Like any other liquid substance, sweat can cause damage mainly to the electrical parts of
the machine (dial, cables, etc.). The best solution is to use a towel during exercise and wipe the
machine after each use to avoid any unwanted damage.
PIC B
PIC A