Xiaomi XWWF01MG-EU User manual
Smart Pet Fountain User Manual
01
Read this manual carefully before use, and retain it for future reference.
Safety Precautions
Warnings
Do not eat the pet fountain or any of its accessories. Use the pet fountain in dry and indoor environments.
Do not place the pet fountain in a high place.
Place the pet fountain on a at surface during use. Do not tilt the pet fountain or knock it over.
Do not add hot water into the water tank.
To avoid electrical leakage from pet bites on the power cord, tidy up the power cord and keep it away
from your pet.
Do not disassemble or repair the pet fountain by yourself.
Do not use any non-genuine accessories. Xiaomi is only responsible for the performance and safety of
ocially provided accessories.
Cautions
Disconnect the pet fountain from the electrical outlet before disassembling and cleaning it. Do not immerse
the pet fountain and the power cord in water.
Clean the inside of the water tank, the cover, and the lter tray with water before rst use. Do not use hot or
boiled water to clean those parts.
There may be a small amount of powder attached to the lter when it leaves the factory, which is normal.
The powder can be washed away with clean water.
It is recommended to replace the lter, the pre-lter, and the pre-lter holder every month, and replace the
water pipe every two months.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
The appliance is only to be used with the power supply unit provided with the appliance.
The appliance must only be supplied at safety extra low voltage corresponding to the marking on the appliance.
This appliance can be used by children aged from 8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children
shall not play with the appliance. Cleaning and user maintenance shall not be made by children without
supervision.
Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between
the antenna and the body of the user.
02
Product Overview
Filter Tray
Filter
Handle
Cover
Water Pipe
Water Pump
Pre-lter
Water Tank
Main Body
Power Port (At the Bottom)
Foot Pad
Smart Mode Indicator
Note: Illustrations of product, accessories, and user interface in the user manual are for reference purposes only.
Actual product and functions may vary due to product enhancements.
Water Level Window
Water Level Indicator
Function Button
Standard Mode
Indicator
03
Package Contents
Pet Fountain Filter Pre-lter
Power Cord User Manual Warranty Notice
04
How to Install
1. Open the cover and clean all the parts before installation.
Note: Do not use hot water or boiled water to clean the parts.
2. Rinse the lter with clean water for two minutes to remove the oating carbon powder generated by the
collisions of the activated carbon during transportation.
05
3. Install the lter and the pre-lter as illustrated.
Pre-lter Holder
Filter Tray
Filter
Pre-lter
Note: If the water pump comes o, reconnect
it with the water pipe.
Note: It is recommended to replace the lter, the pre-lter, and the pre-lter holder every month, and replace the
water pipe every two months. Thoroughly clean the parts including the water tank, the cover, the lter tray, the
lter, the pre-lter, and the water pump at least every seven days.
Water Pipe
06
How to Use
Power Port
1. Connect the power cord to the power port at
the bottom of the pet fountain.
2. Remove the water tank and ll it with water, and
reinstall it. Then close the cover.
3. Plug the power cord into an electrical outlet,
and the pet fountain will start to work.
4. The pet fountain will automatically turn o when
the cover is opened, and then you can add water
to the water tank.
07
Note: The water dispensing time may vary when the pet fountain is oine.
Water Dispensing Mode
Standard Mode
In this mode,the pet fountain can continuously dispense water.
In this mode, the pet fountain can dispense water as follows.
Smart Mode
8:00–22:00: Dispenses water for 10 minutes, and then pauses for 10 minutes, repeatedly.
22:00–8:00 (next day): Dispenses water for 10 minutes, and then pauses for 50 minutes, repeatedly.
Indicator Description
Standard Mode Indicator
Smart Mode Indicator
Note: The standard mode indicator lights up when the pet fountain is
working in the standard mode, and the smart mode indicator lights up
when in the smart mode. Either of the two indicators will light up when
the pet fountain is working.
Water Level Indicator
Mode Indicator
White
Color Status
Orange
Blinking blue
Remaining blue
for 2 seconds Wi-Fi connected successfully
Working normally
Filter exhausted
Awaiting Wi-Fi connection
Water Level Indicator
Red: The water is insucient, please ll the water tank in time.
Blinking red: The water pump is blocked, please clean the water pump in time.
08
Buon Description
Function Buon
Press: Switch the standard mode or smart mode for water dispensing.
Press and hold for 2 seconds: The pet fountain enters standby mode and stops dispensing water.
Press again to resume water dispensing.
Press and hold for 6 seconds: Reset the Wi-Fi connection and restore to factory settings.
The indicator blinks blue.
Function Button
Filter Reset Buon
After replacing the new lter, press and hold the button for 2 seconds to reset the lter.
You can check the remaining service life of the lter in the app.
（at the bottom of the pet fountain）
Filter Reset Button
Press and hold for 7 seconds: Enable or disable the Wi-Fi. When the Wi-Fi is enabled, the indicator is
blinking blue; when the Wi-Fi is disabled, the indicator remains on blue for 2 seconds then goes out.
09
Connect with Mi Home/Xiaomi Home App
Scan the QR code to download and install the app. You will be directed to the connection setup page if the app
is installed already. Or search "Mi Home/Xiaomi Home" in the app store to download and install it.
Open Mi Home/Xiaomi Home app, tap "+" on the upper right, and then follow prompts to add your device.
Note: The version of the app might have been updated, please follow the instructions based on the current
app version.
This product works with Mi Home/Xiaomi Home app*. Control your device with Mi Home/Xiaomi Home app.
* The app is referred to as Xiaomi Home app in Europe (except for Russia). The name of the app displayed on
your device should be taken as the default.
10
Care & Maintenance
Maintaining the Pet Fountain
Power Contact Pin
Power Contact Point
Check whether the ends of the water
pipe are loose or come o.
Note: It is recommended to thoroughly clean the parts including the water tank, the cover, the lter tray, the lter,
the pre-lter, and the water pump at least every 7 days. You are also advised to change the water every 7 days
so that water quality and water dispensing will not be aected due to lter tray blockage.
Check and clean the magnetic fan blades in
the water pump.
Cleaning the Water Pump
1. Open the cover and take
the water pump out.
2. Remove the pre-lter and its
holder from the water pump.
3. Remove the cover of the water pump.
4. Take the magnetic fan blade assembly out. 5. Clean all the parts of the water pump
and then reinstall them in order.
Regularly check whether the power contact pins on the
cover and the power contact points on the main body
are working properly. You can wipe the pins and the
points clean with a dry, soft cloth.
Regularly check whether the power cord
and the power port are in good condition
and working properly.
11
Specifications
Name Xiaomi Smart Pet Fountain
Model XWWF01MG–EU
Input
5.9 V 1.0 A
Item Dimensions 191 × 191 × 177 mm
Capacity
2 L
Net Weight 1.3 kg
Operating Temperature
4°C to 40°C
Operating Humidity
Rated Power
5.9 W 10%–90% RH
Power Cord Length 1.5 m
Power Adapter
Radio Frequency and Radio Transmission Power
Mannufacturer
Input AC Frequency
Output Voltage
Output Current 1.0 A
Output Power 5.9 W
Average Active Eciency
Eciency at Low Load (10%)
No-load Power Consumption
Model Identier
Input Voltage
Jiangsu Chenyang
Electronics Co., Ltd.
CYXT18–059100E3
100–240 V AC
50/60 Hz
5.9 V
≥74.88%
≥64.88%
≤0.075 W
RF Specication
2412–2472 MHz
2.4 G Wi-Fi 19 dBm
Working Frequency Maximum Output Power
12
For detailed e-manual, please go to www.mi.com/global/service/userguide
Regulatory Compliance Information
Europe-EU declaration of conformity
Hereby, Beijing Kitten&Puppy Technology Co., Ltd. declares that the radio equipment type XWWF01MG–EU
is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the
following internet address: http://www.mi.com/global/service/support/declaration.html.
WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU)
which should not be mixed with unsorted household waste. Instead, you should protect human health and the
environment by handing over your waste equipment to a designated collection point for the recycling of waste
electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and
recycling will help prevent potential negative consequences to the environment and human health. Please
contact the installer or local authorities for more information about the location as well as terms and conditions
of such collection points.
Manufactured for: Xiaomi Communications Co., Ltd.
Manufactured by: Beijing Kitten&Puppy Technology Co., Ltd.
(a Mi Ecosystem company)
Address: Room Q-101, Floor 2, Q Area, Anning Zhuang Back Street, Haidian District, Beijing,
China For further information, please go to www.mi.com
Importer:
Beryko s.r.o.
Pod Vinicemi 931/2, 301 00 Plzeň
www.beryko.cz
Table of contents
Other Xiaomi Pet Care Product manuals
