Xilica Audio Design XTouch Series: XTouch50 User manual

1
XTOUCH SERIES
User Manual

2
Important Safety Information
1. READ THESE INSTRUCTIONS
All the safety and operating instructions should be read before the product is operated.
2. KEEP THESE INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED ALL WARNINGS
All warnings on the product and in the operating instructions should be adhered to.
4. FOLLOW ALL INSTRUCTIONS
All operating and use of instructions should be followed.
5. DO NOT USE THIS APPARATUS IN WATER.
Do not use the product near water. For example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a
swimming pool, and the like.
6. CLEAN ONLY WITH DRY CLOTH.
Unplug the unit from the wall outlet before cleaning.
7. DO NOT BLOCK ANY VENTILATION OPENINGS
Slots and openings in the cabinet back or bottom are provided for ventilation, to ensure reliable operation of the limit and to protect it from
overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa,
rug, or similar surface. This product should never be placed near or over a radiator or heat source. This product should not be placed in a
built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
8. DO NOT INSTALL NEAR ANY HEAT SOURCES
This product should be situated away from heat sources such as radiators, stoves or other products (including amplifiers) that produces heat.
9. DO NOT DEFEAT THE SAFETY PURPOSE OF THE POLARIZED OR GROUNDING-TYPE PLUG
A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide
blade or the third prongs are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
10. PROTECT THE POWER CORD FROM BEING WALKED ON OR PINCHED PARTICULARLY AT PLUGS, CONVENIENCE RECEPTACLES,
AND THE POINT WHERE THEY EXIT FROM THE APPARATUS.
11. ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER.
12. USE ONLY WITH CART, STAND, TRIPOD, BRACKET, OR TABLE SPECIFIED BY THE MANUFACTURER, OR SOLD WITH THE APPARATUS.
WHEN A CART IS USED, USE WITH CAUTION WHEN MOVING THE CART/APPARATUS TO AVOID INJURY FROM TIP-OVER.
Do not place this unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury to someone, and serious
damage to the appliance. A unit and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
13. UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.
For added protection for this unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power surges.
14. REFER ALL SERVICING TO QUALIFIED PERSONNEL. SERVICING IS REQUIRED WHEN THE APPARATUS HAS BEEN DAMAGED IN ANY
WAY. SUCH AS, WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED, LIQUID HAS BEEN SPILLED, OR OBJECTS HAVE FALLEN
INTO THE APPARATUS, THE APPARATUS HAS BEEN EXPOSED TO RAIN OR MOISTURE, DOES NOT OPERATE NORMALLY, OR HAS BEEN
DROPPED.
15. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
16. APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES,
SHALL BE PLACED ON THE APPARATUS.

3
Table of Contents
Labels, Descriptions and
Technical Specifications 4-5
Device Connectivity 6-7
XTouch Display Settings 8-9
Install Xilica Designer
Mac OS X Installation 10
Windows Installation 11
Launch Xilica Designer
Network View 12
Firmware Upgrade 13-15
Project View 16
Create a Design 17-21
Going Online 22-24
Contact and Support 25

4
XTouch50 Description
1Power over Ethernet
(PoE)
Connect the device to the network using a standard RJ45
(Ethernet) cable. To send Power over Ethernet, a PoE switch
is needed. If you are sending Power over Ethernet (PoE), the
external power supply is not needed.
2External power supply Insert an external 24VDC/0.5A power supply (not included).
Technical Specifications (XTouch50)
Screen size 5” touch screen
Display HD 1280x720 resolution
Color Depth 16.7M colors, 400 nits brightness
Connectors RJ45 Ethernet, External power supply
Power Power over Ethernet (PoE),
Or 24VDC/0.5A External power supply (not included)
Wall mount Mount onto US/EU/UK 1-gang back boxes or low voltage bracket using
the included XTouch50 mounting bracket
Mounting orientation Portrait or landscape (user-defined)
Rack mount Optional 2RU rack mount panel with 1-gang threaded cut out
Dimensions 5.2”x3.2”x1.3” (132x81x34mm)
Weight 0.4lbs / 0.2kg
Warranty 1 years, parts and labor
1
2
ETHERNET (PoE)
24VDC/0.5A
MODEL: XTOUCH50 MANUFACTURED IN TAIWAN

5
XTouch80 Description
1External power supply Insert an external 24VDC/1A power supply (not included).
2Power over Ethernet
(PoE)
Connect the device to the network using a standard RJ45
(Ethernet) cable. To send Power over Ethernet, a PoE switch
is needed. If you are sending Power over Ethernet (PoE), the
external power supply is not needed.
Technical Specifications (XTouch80)
Screen size 8” touch screen
Display HD 1280x800 resolution
Color Depth 16.7M colors, 400 nits brightness
Connectors RJ45 Ethernet, External power supply
Power Power over Ethernet (PoE),
Or 24VDC/1A External power supply (not included)
Wall mount Mount onto US 2-gang back boxes or low voltage bracket using
the included XTouch80 mounting bracket
Mounting orientation Portrait or landscape (user-defined)
Rack mount Optional 4RU rack mount panel with 2-gang threaded cut out
Table-top Optional TM80 table-top mounting stand
Dimensions 8.7”x5.8”x1.5” (223x149x38mm)
Weight 1lbs / 0.5kg
Warranty 1 years, parts and labor
1
2
LAN / PoE
802.3at compliant
USB
24VDC/1A
MODEL: XTOUCH80
MANUFACTURED IN TAIWAN

6
Device Connectivity
Xilica processors and control devices run on a network based infrastructure and are set up
and controlled by a host computer using the Xilica Designer software.
What’s in the Box
• XTouchhardwaredevice
• Lowvoltagemountingbracket
What you need to Provide
• Computer
• Networkinterface(Router,PoEswitch)
A router is used for IP assignment and easy connectivity to computer and control devices.
A PoE switch is used to power XTouch controls.
•Ethernetcables
All wired connections use a standard RJ45 Cat 5/6 (Ethernet) connection.
Connecting Devices
A network connection can be made between the computer and processor using:
A) DHCP enabled Router or Server/Router combination (Recommended)
With DHCP enabled routers and servers, the processor will automatically obtain the IP address
upon power up and connection. A router and PoE switch provides DHCP as well as power to the
XTouchcontrols.LinksysroutersandNetgearswitchesarerecommended.
B) A non-DHCP direct connection or indirect connection via an Ethernet switch
When the processor is connected directly to a computer or indirectly via a switch/hub and DHCP is
not available, the connection process is not automatic.

7
Note: DHCP enabled Router/switch gear should be turned on first, with all Ethernet cables
connected to the hardware prior to Powering ON the hardware. This will allow for proper IP
address distribution to the Hardware.
First, Power ON the router/switch gear.
Then connect an Ethernet cable from the host computer to the DHCP enabled router.
Connect an Ethernet cable from the router to the PoE switch.
Then connect another Ethernet cable from the PoE switch to the XTouch control(s).
A) Connecting using a DHCP enabled router/server
B) Non-DHCP direct connection or indirect connection
Non-DHCP connections are not automatic. Non-DHCP connections must be manually configured.
Please refer to Xilica Designer help file or Xilica FAQ for further assistance.

8
XTouch Display Settings
XTouch settings can be configured on the front panel of the device.
Swipe up from the bottom of the screen. A menu will appear at the bottom of the screen.
Select the gear icon to view the device settings.
To manually configure network settings, deselect DHCP Enabled and input the new information.
Click Ok to save your changes.

9
Select Advanced Settings... to view more advanced device settings. Click Ok to save your changes.
To view the current App version, swipe up on the screen and select the iicon.
Click Ok to exit the menu.

10
Install Xilica Designer
The Xilica Designer software provides optimum configuration of X2, Solaro and Neutrino Series
processors and it also configures Xilica’s programmable remote controls, configures and manages
any networked Dante device, and provides universal third-party device control integration.
Mac OS X Installation
System Requirements
Mac OS X 10.8 or later
Processor 1GHz or higher
500MB of available space
1GB graphics card
4GB RAM
1. Download the latest version of Xilica Designer from the Xilica website (www.xilica.com).
2. Open the downloaded .zip file.
3. Then open the XilicaDesigner.mpkg file.
4. An installation window will appear. Read and follow each step to proceed.
5. Once completed, the installation window will display: The installation was successful.
6. The Xilica Designer software is now installed.

11
Windows Installation
System Requirements
Windows 7 or higher
Processor 1GHz or higher
500MB of available space
1GB graphics card
4GB RAM
1. Download the latest version of Xilica Designer from the Xilica website (www.xilica.com).
2. Open the downloaded .zip file.
3. Then open the XilicaDesigner.exe file.
4. An installation window will appear. Click Install to continue.
5. Allow the program to complete the installation process. This may take a several minutes.
6. When complete, Windows will ask for permission to allow firewall access. The suggested
setting is to allow Xilica Designer to communicate in Private networks, such as home or work.
Allow access to public networks at your own discretion. Check the appropriate boxes, then
click Allow Access to finish.
7. The Xilica Designer software is now installed.

12
Launch Xilica Designer
LocatetheXilicaDesignerapplicationonyourDesktoporApplicationsfolder.
Double click the application to launch the software.
You can create a New Design Project, Open Design Project, Start Network View, or Start Dante View.
Network View
Network View displays all processors and control devices on the network. Network View displays
device information including, the device connection status, computer IP address, device IP
address, device name, manufacturer and the firmware version.
In Network View, you should see your processor(s) listed. At the top left of each device block is a
device connection indicator.
Green: The device is connected and operational.
Yellow: The device is connected and online, but not operational. Hovering over the network
indicator will display a pop-up message of identified problems. (Normally this would
indicate that no device design is loaded).
Red: The device is not connected and offline. There is no communication between Xilica
Designer software and the device. Please check all cables, connections and power. If the
processor is performing a firmware upgrade or is in the process of rebooting, this may
be a temporary offline interruption.

13
At times you may just see an exclamation mark (!). This indicates that a firmware upgrade is
available. Normally this is not an issue unless there are updated modules in the project file that the
outdated firmware does not support.
Firmware Upgrade
Please note that using an older version of software with a newer firmware or newer software with
an older firmware will work but some of the features may not be available and bugs could exist.
We recommend upgrading the software and firmware to the latest versions.
Before you begin, check your software and firmware versions.
To check the current device firmware version, make sure that your device is connected and online.
In Network View, devices that have a Firmware Upgrade available will display a yellow triangle with
an exclamation mark. The device Firmware version is also listed in the device block.
To view the current software version, click on the About tab at the top of the software.
Matching the Firmware
To assist you in determining which firmware file is appropriate for your device, refer to the chart
below. Note: The file structure may be different from the date that this list was created. Always
check the Xilica website (www.xilica.com) to keep updated.
#_#_# Represents the 3 digit version code of the firmware update.
(SOLARO_#_#_#.img) Solaro QR, FR
(X2_#_#_#.img) X2
(XIO_#_#_#.img) XIO8, XIO16
(XTOUCH_#_#_#.img) XTouch50, XTouch80
(NEUTRINO_#_#_#.img) Neutrino A, A-D (AES), A-N (Dante), A-ND (Dante, AES)
(UNO_#_#_#.img) Uno-U, U-D (AES), U-N (Dante), U-ND (Dante, AES)
(NEUTRINO-AEC_#_#_#.img) Neutrino AEC
(UNO-AEC_#_#_#.img) Uno AEC
(RIO_#_#_#.img) Rio-N, NX
(NEUPANEL MINI_#_#_#.img) NeuPanel Mini K1, K4, S4, S8, S4K1

14
4. A pop-up warning will appear stating that the Firmware Upgrade process will erase all data
from your device. Click OK to proceed.
Firmware Upgrade Procedure:
All programmed data on the device will be erased during the upgrade process. After the firmware
upgrade is completed, the design file can be loaded back into your device.
1. The device must be online and operational (green ON indicator) to perform a firmware upgrade.
2. Download the latest firmware version for your device from the Xilica website (www.xilica.com).
3. In Network View, right click the device block and select Firmware Upgrade.

15
5. Navigate to the file in which you downloaded the new Firmware file. Click Open.
6. A status bar in the device window will monitor the Firmware upgrade progress.
Once the Firmware file has been loaded to the device, the device will automatically restart and
update its internal data. This may take several minutes. During this period, the device network
indicator will turn RED and appear offline.
DO NOT POWER OFF THE DEVICE. Powering off the device during a Firmware Upgrade can
result in a complete corruption of the device. If this happens, a Firmware Recovery must be
completed. (Please refer to Xilica Designer help file or Xilica FAQ for further assistance).
Once the firmware upgrade is completed, the device will display a green ON indicator.

16
Project View
You can create a new project in one of two ways:
Auto-configuration
If your device is listed in network view, select your device and click Create New Project with
Selected Device(s) at the top right of the software. This will create a project with your device.
Blank project
Alternatively, click File > New Project.
When creating a blank project, Xilica Designer will ask you which product series you are using.
Select the appropriate option.
1. Component Library Menu
This menu displays a list of devices and design modules that you can use in your project.
2. Work Area
The work area provides a space to design and configure devices.
3. Object Property Menu
This menu allows you to customize the object properties in the design.

17
Create a Design
Projects can be designed Offline (no devices connected) and the design can be loaded to your
devices at a later time.
The following example uses a completed project design. (Please refer to Xilica Designer help files).
1.FromtheComponentLibrarymenu,draganXTouchcontrolontotheworkarea.
With the object highlighted, you can customize the object properties in the Object Property menu.
Note: Object Properties vary depending on the object selected.
2. Double click the XTouch Control module to open the device.

18
3. On the left side of the window, click Resize Panel and select the screen size of your device. You
can also set a custom defined size if your device is not listed. Then click Ok.
The work area will reflect the Panel Size.
Resize the window by dragging the corner of the window and using the zoom slider.
4. Move the XTouch control window to the side. Double click the device that you would like to
control and move the window beside the XTouch window. You can also click the Tile icon at
the top right of the window to automatically arrange the windows, side-by-side.
In the example, a Neutrino DSP is opened.

19
5. Double click a DSP module. Drag a select box around the desired controls/elements,
Or hold Ctrl + Click to select individual elements.
6. With the DSP parameters highlighted, click and drag the parameters onto the XTouch control.
7. Customize objects using the Object Property menu.

20
When working in the XTouch window, the Component Library menu will list 3rd party control
elements, drawing elements, buttons, web browser, and saved project presets.
To create project presets, please refer to Xilica Designer help files and Xilica FAQ.
8. Drag and drop any element onto the XTouch control to add it.
9. Customize elements in the Object Property menu.
10. Add, Delete and Rename pages in the left pane of the XTouch control window.