Xilinx ZC702 Si570 Installation guide
November 2014
ZC702 Si570 Programming
XTP181
© Copyright 2014 Xilinx, Inc. All Rights Reserved.
XILINX, the Xilinx logo, the Brand Window and other designated brands included herein are trademarks of Xilinx, Inc. All other trademarks are the property of
their respective owners.
NOTICE OF DISCLAIMER: The information disclosed to you hereunder (the “Information”) is provided “AS-IS” with no warranty of any kind, express or implied.
Xilinx does not assume any liability arising from your use of the Information. You are responsible for obtaining any rights you may require for your use of this
Information. Xilinx reserves the right to make changes, at any time, to the Information without notice and at its sole discretion. Xilinx assumes no obligation to
correct any errors contained in the Information or to advise you of any corrections or updates. Xilinx expressly disclaims any liability in connection with technical
support or assistance that may be provided to you in connection with the Information. XILINX MAKES NO OTHER WARRANTIES, WHETHER EXPRESS,
IMPLIED, OR STATUTORY, REGARDING THE INFORMATION, INCLUDING ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NONINFRINGEMENT OF THIRD-PARTY RIGHTS.
Revision History
Date Version Description
11/24/14 12.0 Recompiled for 2014.4.
10/08/14 11.0 Recompiled for 2014.3.
06/09/14 10.0 Recompiled for 2014.2.
04/16/14 9.0 Recompiled for 2014.1.
12/18/13 8.0 Recompiled for 2013.4.
10/23/13 7.0 Recompiled for 2013.3.
06/19/13 6.0 Recompiled for Vivado 2013.2.
04/03/13 5.0 Recompiled for 14.5.
12/18/12 4.0 Recompiled for 14.4.
10/23/12 3.0 Recompiled for 14.3. Added AR52580.
07/25/12 2.0 Recompiled for 14.2. Added AR47530.
05/25/12 1.0 Initial version for 14.1.
ZC702 Si570 Programming Overview
Xilinx ZC702 Board
Software Requirements
Setup for the ZC702 Si570 Programming
Programming the Si570
Calibrating the Frequency
References
Note: This presentation applies to the ZC702
ZC702 Si570 Programming Overview
Description
–The ZC702 board has a Silicon Labs Si570 Programmable Oscillator that
defaults to 156.25 MHz. Via the IIC bus, the frequency of this device can be
changed. This tutorial shows how to change the output frequency of this
device.
Note: Presentation applies to the ZC702
Xilinx ZC702 Board
Vivado Software Requirements
Xilinx Vivado Design Suite 2014.4, Design Edition + SDK
–Combined installer
Note: Presentation applies to the ZC702
ZC702 Setup
Connect a USB Type-
A to Micro-B cable to
the USB JTAG
(Digilent) connector
on the ZC702 board
–Connect this cable to
your PC
–Set the JTAG Select
Switch, SW10, to 01
–If using a Platform
Cable USB (II) JTAG
Cable, set SW10 to 10
Note: Presentation applies to the ZC702
ZC702 Setup
Connect a USB Type-
A to Mini-B cable to
the USB UART
connector on the
ZC702 board
–Connect this cable to
your PC
–Power on the ZC702
board for UART Drivers
Installation
Note: Presentation applies to the ZC702
ZC702 Setup
Reboot your PC if necessary
Right-click on My Computer
and select Properties
–Select the Hardware tab
–Click on Device Manager
Note: Presentation applies to the ZC702
ZC702 Setup
Expand the Ports
Hardware
–Right-click on Silicon Labs
CP210x USB to UART
Bridge and select Properties
Note: Presentation applies to the ZC702
ZC702 Setup
Under Port Settings tab
–Click Advanced
–Set the COM Port to an open Com Port
setting from COM1 to COM4
Note: Presentation applies to the ZC702
Setup for ZC702 Si570 Programming
Unzip the ZC702 Si570 Programming Design Files (2014.4 C) ZIP file
–Available through http://www.xilinx.com/zc702
–It is recommended to unzip these design files to C:\ for SDK compatibility
Note: Presentation applies to the ZC702
ZC702 Si570 Programming
Connect a scope to J63 (PMOD1), pins 4 and 6 to measure the
frequency
Si570 Power on frequency is 156.25 MHz
Frequency is divided by 10 in the Zynq PL
Measured frequency on these two pins will be ~15.625 MHz
Note: Presentation applies to the ZC702
ZC702 Si570 Programming
For this example, Si570_0 will be reprogrammed from 156.25 to 200
MHz
–This requires use of the SiLabs Programmable Oscillator Calculator
To use the SiLabs calculator, the correct fXTAL value for each Si570
must be determined, using this equation:
For this equation,
–Fout = 156.25, the preprogrammed frequency of the Si570s on the ZC702
We need to determine:
–RFREQ
–HSDIV
–N1
These can be found by reading back the registers on the Si570
Note: Presentation applies to the ZC702
ZC702 Si570 Programming
The terminal window shows the current register settings for the
Si570
–The power-on values will appear in the terminal window
–Note the value of 0x01C2BBFFFBA4
Note: The values reported by your
Si570 may differ from those shown
ZC702 Si570 Programming
The value, 0x01C2BBFFFBA4, corresponds to the contents of the
Si570’s registers, 7 to 12:
Note: Presentation applies to the ZC702
Table of contents
Other Xilinx Motherboard manuals
Xilinx
Xilinx Zynq ZC702-G User manual
Xilinx
Xilinx KC705 Si5324 User manual
Xilinx
Xilinx Zynq UltraScale+ ZCU208 User manual
Xilinx
Xilinx KC705 User manual
Xilinx
Xilinx ZCU102 User manual
Xilinx
Xilinx ML605 Installation manual
Xilinx
Xilinx VC707 User manual
Xilinx
Xilinx Artix-7 FPGA AC701 User manual
Xilinx
Xilinx Virtex-7 FPGA VC7222 IBERT User manual
Xilinx
Xilinx KC705 User manual
Xilinx
Xilinx Kintex-7 FPGA KC705 User manual
Xilinx
Xilinx Spartan 6 FPGA User manual
Xilinx
Xilinx VC707 User manual
Xilinx
Xilinx VCK190 Series User manual
Xilinx
Xilinx Virtex-7 FPGA VC7222 IBERT User manual
Xilinx
Xilinx Spartan-3E User manual
Xilinx
Xilinx Virtex-4 RocketIO User manual
Xilinx
Xilinx SP601 User manual
Xilinx
Xilinx XtremeDSP Spartan-3A DSP 3400A... User manual
Xilinx
Xilinx Virtex-7 FPGA VC7222 IBERT User manual
