Xintex P-1BS-R User manual

xNrEx.
Propane Fume Detection System
With Solenoid Valve Control
Single ChannelSvstems
P-1BS-R (Black, Round, Solenoid Control)
P-1CS-R (Chrome, Round, Solenoid Control)
Dual Channel Svstem
P-2BS-R (Black, Square, Solenoid Control)
Owner's Manual
&
lnstallation lnstructions
Read and comply with all instructions, warnings and limitations before
installing, servicing or removing this device.
1,
Part Number 18143, B, 01.12712017

Additional copies of this manual are available at no charge by contacting the manufacturer,
distributor or dealer. Fireboy-Xintex reserves the right to change features without notice.
General lnformation
Specifications
Operation of Xintex Propane Fume Detector(s)
Installation
lnstalling the Display Unit (p1BR-S01-D/P1CR-SO1-D & p2BS_SO1D)
Routing Sensor Cable(s) (FS-X01 CABLE XX,)
lnstalling Propane Fume Sensor(s) (FS-TO1)
Electrical Connections (P j.BR-SO1-D/p1CR-SO j.-D & p2BS-SO1D)
Testing the System Operation
Testing the Propane Fume Sensors
Maintenance
ln the Event of an Alarm
Repairing Xintex Propane Detection Components
Returning Xintex Propane Detection Components
L Year Limited Warranty
2
Part Number 18143, B, Ot/2712077
3
3
4
6
5
6
6
7
7
7{+
7
8
8
8
9

l-
General lnformation
PROPANE FUME DETECIORS ARE MEANTTO SERVE AS A SUPPLEMENTAT WARNING SYSTEM. IT IS
NOT MEANT TO REPLACE STANDARD SAFETY PRACTICES WHICH SHOULD BE CARRIED OUT
AROUND EXPLOSIVE GASES.
The p-1BS-R, P-lCS-R, and P-2BS-R Propane Fume Detectors are an effective means to monitor
propanefumesinacompartmentorleakingfuel systems. lnaddition,theseunitshavetheability
tocontrol theflowofCNG/LPGtoyourappliances. Thesystemusesasensor, locatedinaplaceof
interest, and a central display unitthat notifies you ofthe state ofthe system.
Specification
Svstem Specifi cations (P-1BS'R/P-1CS-R)
Operating Voltage: 9-30 VDC
Nominal Current Draw: 55mA @ 12 VDC
Maximum Current Draw: 725mA @ 9 VDC
Operating Temperature: -40"F (-40"C) to 185"F (85'C)
Alarm Horn: = 68dB
Svstem Specifi cations (P-2BS-R)
Operating Voltage: 9-30 VDC
Nominal Current Draw: 95mA @ 12 VDC ,
Maximum Current Draw: 780mA @ 9 VDC -
Operating Temperature: -40"F (-40"C) to 185'F (85"C)
Alarm Horn: = 68dB
3
Part Number 781.43, B, Otl27 120L7

Operation of Xintex Propane Fume Detector(s)
There are 3 LEDs located on the Display Unit for each channel on the system, as well as an LED for
theSolenoidValvestatus. TheGreenLED, locatedatthetop,indicatesthatthesystemis
operational. The Yellow LED, located in the center, indicates that there is a Fault in the system.
Thisistonotifytheusertochecktheconnectionsandwirerunsofthesensors. Theremaybea
break in the wiring or a disconnected sensor on that channel. The Red LED, located at the bottom,
indicates a fume buildup ol 20% ol the LEL (Lower Explosive Limit) which is considered an a larm.
The alarm horn will sound when the Red LED is illuminated. The alarm horn will actuate, Solenoid
Valve will close, and the Solenoid Valve status LED will deactivate when the Red LED is
illuminated. Wheneverthe Solenoid Valve status LED is illuminated, the Solenoid Valve is open.
PlBR-SO].-D
P1CR.SO1.D
P2BS-SO1-D
The alarm status will continue as long as the fume level remains at an elevated level. The alarm
horn may be silenced by pressing the "Check/Reset" button. The alarm will reactivate after 30
seconds as long as the Detector remains in alarm status. The problem should never be considered
corrected as long as the Red LED is illuminated.
4
Part Number 1.8L43, B, OL/27 12017

_<€
ElP
E E"E= E
uuN O >^
uoYo33
o';o-ooo
=5TE3;
! 3; =e);
@
t-
..sP
11i
ll I
H
il
n
trl
B
E
x
ll x
ll x
li u
-x_ d
-f- g
Ell e
OHL
efl
EtrI
@
il
I
11
'. -U-
o...s
tn
6il
Lll H
E
n
m
@
n
E
il
ll o
-U6
xll r
xll r
ull o
JH-
e*5
U HC
dnd
oll ^
>< ll +
tzrA-
r-o HA
l Id
-'* mA
-H
!
'og
C=
o6
E>
_<€
EIE
E E"E= E
IuN O >!
8E;3s".H
= 5 T E.3 ;
i 3 e 2 Qr.t
@
u
t
-'S- r
lo
ll f
n
n
rhl
@
t_.1
I
il><
llx
l-
ll J
ll co
_H_ 3
-tl- a
ll o
II T
ll r
o11
rll
*-n
5H
.jm
-c,
';o
E>
oo
6>
c
J
(9
bo
c
=
o
.;
I
=
o
J
)
U
E
E
5
o
(9
bo
c
E
I
'=
I
=
o
J
J
U
C
5
o
(,
I
:z
(J
l
co
3
o
B
o
d
I
o
U
E.
oo
dd
oo
d,E
co (J
dd
Ld
5
Part Number L8L43, B, 0L12712017

I lnstallation
Installine the Displav Unit (p1BR-S01-D/p1CR-SO1-D & p2BS-S0i"D)
The Display Unit should be located at the instrument panel, so that the visible and
audible indicators may be easily observed.
Drill a 2-1./16" hole to accommodate the plBR-So ].-D/P1CR-SO1-D Display Unit.
Drill a 2-1/8" hole to accommodate the p2BS-SOI-D Display Unit.
lnsert Display unit into hole and secure with the provided threaded mounting nut.
DO NOT MAKE ELECTRICAL CONNECTIONS AT THIS TIME. THEY WILL BE ADDRESSED IN A LATER
SECTION
Routine Sensor Cable(s) (FS-X0L CABLE XX')
A 20 FT Sensor cable is provided for each propane Fume sensor. The sensor Cables
should be routed starting at the Display unit, then to the pre-determined location ofthe
Propane Fume sensor. connect to the Display Unit using the attached quick-disconnect
connectors. Take care not to pinch, break, or cut the sensor cable or put too much
stress on the connectors while routing the cable. secure the sensor Cable with the
appropriate hardware for the application.
DO NOT CUT EXTENSION CABLE FOR ANY PURPOSE. DOING SO VOIDS THE PRODUCTS
WARRANTY. LONGER CABLES ARE AVAILABLE FROM 20 FTTO 1OO FT.
lnstalline Propane Fume Sensor(s) (FS-T01)
The Propane Fume sensor should be located by the propane powered appliance, near
the floor. Avoid areas where damage may take place due to cleaning, mopping, kicking,
or other physical damage. Harsh chemicals should not be used to clean sensors.
Use the appropriate #8 mounting hardware to mount the propane Fume Sensor in the
desired location. The rubber gasket should be installed between the sensor and the
mounting surface.
Connect to the Extension Cable using the attached quick-disconnect connectors.
6
Part Number 18143, B,01./27/20t1

lnstallation Continued
Electrical Connections (P1,BR-SO1-D/P1CR-S01-D & P2BS-S01-D)
The Display Unit operates on 9-30 VDC. A Red and a Black 16 GA wire are provided for
connecting to the power source. Connect the Red wire to Power (+) with an inline 1.0
Amp fuse. Connect the Black wire to Ground (-).
A Yellow 16 GA wire is provided for connecting the Display Unit to the Solenoid Valve.
Connect the Yellow wire to the Ground terminal for the Solenoid Valve. Connect the
+12 VDC to the Solenoid Valve through a dedicated 2A circuit breaker. A 24 fuse should
be used if powering Solenoid Valve at the Display Unit.
Testing the System Operation
The Propane Fume Detectors can be tested by pressing the "Check/Reset" button on the face of
theDisplayUnit. TheDisplayUnitwill cyclethroughtheLEDsandthealarmhornwill activate
while the LEDs cycle.
UnplugthePropaneFumeSensorfromeachchannel oftheDetectionSystemoneatatime. The
Yellow "Fault" LED should illuminate. lf the Yellow LED does not illuminate, remove Display Unit
and return direct to manufacturer following the instructions at the back of this manual.
To test the Solenoid Control function, check that the flame of your appliance extinguishes when
the Solenoid Control function is turned OFF.
Testing the Propane Fume Sensors
DO NOT USE A PROPANE SOAKED RAG OR A PARTIALLY FULL CONTAINER OF PROPANE TO TEST A
SENSOR. THE RAW PROPANE COULD IGNITE, RESULTING IN SERIOUS INJURY.
Test the Sensors by holding a Butane lighter to the sensor. Within a few seconds, the Red
"Danger" LED should illuminate and the alarm horn will sound. Remove the lighter from the
Sensor and mute the alarm horn. After approximately one minute, the Red LED will shut off'
Maintenance
The system should be tested periodically in the fashion described in the previous sections. Due to
the harsh environmental conditions in marine applications, it is recommended to replace the
Propane Fume Sensors every 3-4 years.
7
Part Number L8143, B, 0L/2712017
IMPROPER CONNECTIONS WILL DAMAGE THE DISPLAY UNIT AND WILL VOID WARRANTY.

ln the Event of an Alarm
lmmediately have all passengers and crew exit the passenger compartment and vessel if possible
Ventilate the space being monitored.
Carefully check all fuel lines and other potential.sources of propane fume leaks. lf leaks are
identified, shut off fuel supply and make any necessary repairs.
Repairing Xintex Propane Fume Detection Components
Xintex Propane Fume Detection Components are notfield serviceable. Components must be
returned to the factory for any repairs.
Returning Xintex Propane Detection Components
No product may be returned for credit or repair without a written "Returned Material
Authorization" (RMA) form. Purchaser must call or email Fireboy-Xintex 516-735-9380 or
[email protected] for a RMA. lf due to extenuating circumstances a product is to be
returned, afterapproval it must be received in1..OO% new/resalable condition. Products stored by
the buyer for more than 26 weeks may not be returned for any reason. Maintaining fresh and
current inventory is the responsibility of the buyer.
8
Part Number 18143, B, 0L/2712017
---f

L Year Limited Warranty
This Warranty is in lieu of all other expressed or implied Warranties
Seller warrants title, materials, and workmanship on equipment, except components
manufactured by others for which the Seller assigns, as permitted, the original manufacturer's
warranty. Seller's warranty shall be for a period of (1) one year from the date of sale to the
ORIGINAL CONSUMER PURCHASER, during which non-conforming equipment returned to the
Seller at Buyer's expense and risk, be repaired or replaced at the Seller's option. Fireboy-Xintex,
lnc. will repairor replace products found to be defective in materials orworkmanship within the
period set forth above, provided that: (a) the product has not been subjected to abuse,
contamination, neglect, accident, incorrect wiring not our own, improper installation or servicing,
or used in violation of instructions furnished by Fireboy-Xintex, lnc. and (b) as to any prior defects
in materials or workmanship covered by this warranty, the product has not been repaired or
altered by anyone except Fireboy-Xintex, lnc and (c) the serial number has not been removed,
defaced or otherwise changed, and (d) examination discloses, in the judgment of Fireboy-Xintex,
lnc., does not assume the costs of removal and/or installation of the product or any other
incidental costs of removal and/or installation ofthe product or any other incidental costs which
mayariseasaresult ofanydefectinmaterial orworkmanship,and(e) upondiscoveryof defect,
Buyer shall immediately cease use of and notify Fireboy-Xintex, lnc.
Any warranty implied by law, including warranties of merchantability or fitness, is in effect only
for the duration of the expressed warranties set forth above, no person is authorized to give any
other warranty, or to assume for Fireboy-Xintex, lnc. any other liability in connection with the sale
of its products; Fireboy-Xintex, lnc. shall not be liable for the loss of use, revenue, or profit or for
any injury, or for any other consequential or incidental damages, buyer is not relying on seller's
judgment regarding his or her particular requirements, and has had an opportunity to inspect the
product to his or her satisfaction.
This warranty gives you specific legal rights, and you may also have other rights, which vary, from
state to state.
www.fireboy-xintex.com
Fireboy-Xintex, lnc.
0-379 Lake Michigan Dr. NW
Grand Rapids, Ml 49534
fi reboy@fireboy-xi ntex.com
Phone [phone]
Fireboy-Xintex, LTD
10 Holton Road, Holton Heath Trading Park
Poole Dorset BH16 6LT UK
fi reboyeu @fi reboy-xi ntex.com
Phone [phone]
9
Part Number 18143, B, 01127/2017