XPower A-2 User manual

XPOWER ®
Electric Duster Owner's Manual
Fluffier° Electric° Manual de Usuano
Depoussiereur Electrique Manuel d'emploi
Model / Modelo / Modele:
A-2
(115V 60HZ)
Read and save these instructions
Lea y guarde estas instrucciones
Lisez et epargnez ces instructions
Intertek
www.xpower.com
I
1-(855)-855-8868 I [email protected]
Index: NA-1 83
Edition: 1.5.Fina I

L
WARNING - READ AND SAVE THESE INSTRUCTIONS BEFORE USING THIS
PRODUCT.
The user of electrical products may create hazards that include, but are not limited to
injury, fire, electrical shock. Failure to follow these instructions may damage and/or impair
its operation and void the warranty.
•
Before operating. remove all packaging material and check for any damage that may
have occurred during shipping or any missing items.
• Check household power supply to ensure it matches the appliance's specification.
•
To reduce the rink of electric shock, this appliance has a polarized plug (one blade is
wider than the other). This plug is intended to fit into a polarized outlet only one way. If
the plug does not fit fully into the outlet, reverse the plug.
If it
still does not fit, contact a
qualified electrician. DO NOT
change the plug in any way.
• DO NOT
use with damaged cord or plug. If the appliance is not working as it would, or
has been dropped, damaged, left outdoors, or dropped into water, return it to a service
center,
• DO NOT pull or carry by cord, use cord as a handle, close a door on cord, or pull cord
around sharp edges or corners.
• DO NOT run appliance over cord. Keep cord away from heated surfaces.
•
The unit's electrical cord cannot be replaced. If the cord is damaged, the appliance
should not be used further.
• DO NOT
touch this appliance or the plug with wet hands or while standing in water.
• DO NOT
allow to be used as a toy. Close attention is necessary when used by or near
children.
• DO NOT
leave appliarce when plugged in. Unplug from outlet when not in use and
before servicing,
•
Turn off all controls before unplugging. Remove the power cord from the electrical
receptacle by grasping and pulling on the power cord plug-end only.
DO NOT pull The
cord directly.
•
Use only as described in this manual. Use only manufacturer's recommended
attachments.
• DO NOT put any object into openings. DO NOT
use with any opening blocked; kecp free
of dust, lint, hair, and anything that may reduce air flow.
•
Keep hair, loose clothing, fingers and all parts of body away from openings.
• Use extra care when cleaning on stairs.
•
If the appliance Is damaged or it malfunctions,
DO NOT
continue to use it. Unplug the
product from the electrical outlet. Refer to troubleshooting guide or contact XPOWER.
•
Store in a dry indoor area, away from exposure to sunlight, rain, extreme temperature
and humidity, or other extreme environments, when not in use.
• Arm electronic instruction manual can be obtained through manufacturer's website gegyu
>mower. QOM.
Special
lastructiohe
This product is ETL/C.ETL certified.
•
The ETL (Electrical Testing Laboratory) Listed Mark is proof that this product has been
independently tested and meets the applicable published safety standard of North America.
A
EletrIc Motor Driven Tools:
(1) Sparks
(1.1) Sparks may be visible on occasion due to the electric motor. Various factors may
cause this such as prolonged or intensive use, foreign objects or an imbalanced
motor.
(1.2)
PO NOT
use this product around flammable or explosive materials such as gas, oil
and chemicals. Sparks can igpite these materials and cause fire.
(1.3) Occasionally small amounts of sparks are safe if away front flammable or explosive
materials. Please follow the instructions of the troubleshooting guide. (5._Paae12.1.
Troubleshooting Cu/dc)
(1.4) If the amount of sparks exceeds the safe range, a thermal protection fuse will stop
this product completely. Please contact XPOWER or other parties authorized
by
XPOWER for further instructions.
(1.5) If sparks continue or you have a
large
amount of sparks, we will consider your
machine as a defective unit Please stop IASI ng immediately and contact XPOWER or
Other parties authorized by XPOWER for return or further instructions.
(2)
Temperature Level
(2.1) This product generates heated air from the powerful motor After prolonged use, the
airflow and the machine surface can reach nigh temperature levels.
12.2) Please be aware Mat the objects under high temperatures can be damaged. Follow
the instructions of the troubleshooting guide. tovu.ei2t
Troubtesbootiv Guide)
(2.3) If thetemperature exceeds the safe range, a thermal protection fuse will shut
down the unit automatically. Please contact XPOWER or other parties authorized by
XPOWER for further instructions.
(3)
Noise Level
(3.1) This product uses a high RPM (Revolutions Per Minute) motor to provide powerful
airflow and can create a high level of noise.
(3.2) Please follow the instructions of the troubleshooting guide. (See Page 12_
Troubleshooting_Ouicie)
A
if you drop this product:
(1)
Before the next usage, please point to a safe area and turn on the unit with the low speed
setting for 5 minutes. And then switch to the higher speed setting for another 5 minutes.
(2)
If you experience abnormal sparks, temperature or noise level occur during the above
operation, please immediately stop using and contact XPOWER or other parties authorized
by XPOWER for further instructions.
English -2 
English -3

English -4
English. 5
• The XPOWER Electric Duster produces a powerful airflow for
endless applications with various nozzle attachments.
•
Its ideal to dust, pump air, and dry a variety of surfaces with its
power and flexibility.
•
With a high pressure airflow, it's also designed to help drying a
bathed pet in your home.
Cl
Electric Dusters 1 Nozzle Att hrnrents 9
n
• Owners Manual x
• Nozzle Pouch x1
7TTij
17
9
8
/
12
13
(1)
Housing  (8) Standard Nozzle  Adapter
(2)
Air Cutlet  (9) Standard Brush  13.2) Boston Valve
(3) Air Inlet  (10) Detail Brush  Adapter
(4) Filter  (11) Strew Adapter 
(13.3) Stem Voice
(5) Speed Switch 
(12) Tapered Flow Nozzle  Adapter
6) Handle  (13) Air Pump Adapter set  (14) Power Cord
(7) Air Blade Nozzle
 (13.1) Wide Valve
Standard Nozzle
• The standard nuzzle can be used
alone. Attach the standard nozzle to
the air inlet of the electric duster,
•
Push and fasten the nozzle.
Standard Brush
•
The standard brush must be attached
onto the standard nozzle.
2
11
Nozzle Installation
(See Pare 4 Parts Descrition)

Th
ON
The tapered flow nozzle, straw
adapter and the detail brash should
be used together.
Tapered Flow Nozzle
Attach the straw adapter Otto the
tapered flow nozzle.
Straw Adapter
• Insert the detail brush insidethe
other end of the straw adapter.
Detail Brush
Attach the whole set of the nozzles
onto the electric duster.
Air Blade Nozzle
• Simply attach the air blade nozzle to
the air inlet of the electric duster.
NozztltitaJtatIo(ContInued)
English - 6
Air Pump Adapters
• The air pump adapter set consists
of three adapters. Each adapter is
designed for different kind of inflatable
valves.
•
Simply attach the desired adapter to
the air inlet of the electric duster.
WARNING
• 00 not tape or block the breathing holes on
the tapered flow nozzle and the air pump
adapters.
• The breathing boles allow the machine to
release the air pressure when the Straw
adapter or the detail brush is blocked.
•
Blocking the breathing holes could cause
serious failure on the machine and void the
warranty.
PoSupp
Amperage Rating
• This appliance consumes high amperage electricity of 4.5 A (See Pare tl Technical
Specifications).
•
Make sure you have a power socket with a compatible amperage rating and fuse
setting. You should also check if the power circuit of your building can support the total
power consumption of all the devices including this appliance.
English -7

witch
•
Switch to W position to turn the electric duster OFF.
Switch to other positions to tern the electric duster
ON.
• There are two speeds settings: I and II.
 is the
lower speed and iI is the higher speed.
Stem Valves (inner diameter k ¼ inch / 6 mm)
Boston Valves (Inner diameter between ½ inch! 12 mm and Vs Inch / 22 mm)
,.Stái.t*ur J.bWfltInu.d)
Used As on Air Pump/inflating (See Page 4:
Parts Descrtztiort(
•
Install the matched air pump adapter onto the electric duster.
•
Open the valve and insert the adapter into the valve until the adapter cover the whole
Intake.
•
Turn on the machine with the lower speed setting (recommended) and start inflate. Use
your hands to feel if there is enough air.
•
Turn off the machine when finished. Close the valve.
StturJob
Before Turning on the Electric Duster:
Please hold the handle tightly and point to a safe area.
Dusting a Computer or Other Devices (See
Page 4: Parts Description)
Recommended nozzles: standard nozzle, standard brush, tapered flow nozzle, straw
adapter and detail brush.
• Disassemble the computer (or other desired devices) and put the computer (or other
desired devices) in a outdoor place (recommended).
• Install the standard nozzle and turn on the electric duster with the higher speed setting.
Roughly dust the surface of the computer (or other desired devices).
• Install the standard brash onto the standard nozzle to remove difficult dirts.
• Switch to tapered flow nozzle with straw adapter and detail brush installed to clean
crawl places.
• Switch to standard nozzle again to dust out the whole surface.
Used As a Hair Dryer for Pet (cee Pete 4 Party
Oescrioniors)
Recommended nozzles: standard nozzle and air blade nozzle.
• Force Drying Stage: In this stage, pets have been bathed and are saturated with heavy
water. High-pressure airflow can remove the heavy water efficiently. You can achieve
high-pressure air by installingthe standard nozzle or air blade nozzle and dry atthe
higher speed setting of the machine.
• Finish Stage: In this stage, most of the heavy water on the pets have been removed in
the force drying stage, bat there is still some moisture. Heated temperature and high-
volume soft airflow can help to vaporize the rest of the moisture or to fluff and style.
Switch to the lower speed setting and dry. For long coated pets, use the air blade nozzle
to prevent knotting in the drying process.
English - 8

English - 9

s. NIS
User, Maintenance Instructions
ration Guide
Frequent maintenance is recommended on this appliance. Failure to follow the
maintenance instructions may cause failure of the appliance and void the warranty.
Other Valves (Inner diameter between
?/a
Inch / 22 n,m and 1
1 / 4 Inch/ 32 mm)
WARNING
•
Do not operate the machine with air inlet or outlet against any flat surface
directly.
•
This could block the air inlet or outlet and cause serious failure on the machine
and void the warranty.
English - 10
•
When not in use, unplug and store the appliance it a dry and cool indoor place. Make
sure its out of reach of children.
•
Before performing any maintenance or cleaning, always disconnect the electric duster
from its power source.
•
Use a damp cloth to wipe the surface of the housing. Do not clean the unit with water
directly.
•
Cheek if the air inlet and outlet are clean. Remove dirt or any other objects that could
block the air inlet and az outlet.
Fili**ebrumance
There is one filter on the bottom (intake)
of the machine. To ensure the best
performance, you should clean or replaces
the filters frequently. (See
Also Page 3
Parts
Deseription).
oizfeftachmoit Makitfl*$c.
•
Use water to removed Its or any other objects on the nozzle attachments. Pay attention
to the possible hidden dints on the standard brushand detail brush.
•
Dry the nozzle attachments in natural wind or with the electric duster.
•
Restore the nozzle attachments in the nozzle pouch out of reach of children.
English - il

$ 7 747
,„
.i.:1....0i 4,4 ' 41'
'
PROBLEM  niteSsibLE. CAUSE
Electric duster No electricity.
does not start
The power cord is not properly
plugged in.
Unit runs but

Air inlet or air outlet is blocked.
the speed is
abnormal
Noise

This product uses a high RPM
motor to provide powerful airflow
and could creates certain level of
noise. This is a normal sound.
• ,,
Air inlet Or air outlet is blocked
Abnormal 
This product generates powerful
Temperature 
motor heated air. After a
of the airflow 
prolonged use, the airflow and
or housing 
the machine surface might reach
a high temperature.
Sparks

Occasion small amount of sparks
generated by the motor during
normal operation.

„„.
Unit works with continuous
spa , ks.
Nozzle falls off The nozzle is not properly
installed.
(See
P a ge 3t
Special Instructions)
SOLtnintav
Check for power supply.
Remove and reconnect the power
cord.
Remove blockage and clean the
filter or nozzle attachment.
. Stop using for at least one hour
until fully cooled down. Clean the
filter and check if the air inlet or
outlet is blocked. Use a glove the
isolate the heat coming from the
housing.
„.
This is normal. Use nozzle
attachments to arrest most of the
occasion sparks along use.
„
Stop using for at least one hour
until the unit cools down. Clean
the filter and check if the air inlet
or outlet is blocked. Then point
to a safe area and turn on the
machine for 5 minutes. Spark
should disappear.
Follow the installation guide.
Fasten the nozzle before use.
MODEL NUMBER
Voltage/Frequency
Amperage
Motor Power
Rated Airflow
Speed Control
Cord Length
Unit Dimension (L) x (W) a (H)
Unit Weight
Safety Certification
Use a wider opening nozzle
, attachment, switch to the lower
speed setting or operate in a
- outdoor place.
Remove blockage and clean the
filter or nozzle attachment.
A-2
115 V-60 Hz
4.5 A
540W
90 CFM
2 Speeds
10ft./ 3 m
6.75 x 3.82 x 7.22 In./ 17.2 x9.7 518.3 cm
2.3 lbs.  kg
ETL/C ETL
If troubleShooting does not resolve your problem, please contact XPOWER or other parties
authorized by XPOWER for further instructions.
English - 12

English - 13

XPOWER Limited anty (USA)
(Dentine
1 YEAR LIMITED WARRANTY
XPOWER-branded products purchased in the U.S. from authorized distributors include
a 1-year limited warranty. Contact XPOWER to confirm warranty information about your
product(s).
This limited warranty covers defects in materials and workmanship in your XPOWER-
branded products, purchased in the
U.S. ONLY.
Local warranty policy (if any) in your
country will cover products purchased outside the U.S.
A
IMPORTANT:
(1)
Please finish the online warranty registration before usage. Visit www.mower.
com/service-suoDort/warrantv-registratiori.
(2)
This Limited Warranty applies with its own timeliness. Contact XPOWER or visit www.
xpower.corn for more information.
Items mentioned but not limited to below are not covered by warranty:
(1)
Power cord, filters or any other components considered as a "consumable parts" by
XPOWER.
(2)
Normal wear and tear.
(3)
Problems that result, directly or indirectly, at XPOWER's sole discretion, from:
(3.1) External causes such as accident, abuse, misuse or problems with electrical
power supply.
(3.2) Disassembling, servicing or modification not authorized by XPOWER.
(3.3) Usage that is not accordant with product instructions stated in Owner's Manual.
(3.4) Failure to follow the product instructions or lack of necessary maintenance
stated in Owner's Manual.
Before contacting XPOWER, please try one or more of the following:
(1)
Consult this Owners Manual and follow the instructions of troubleshooting guide.
(2)
Access www.xoower corn for more advice and information that could be helpful to
address your problems.
If you need additional assistance from XPOWER, please:
(1) Email [email protected]
.
(2)
Call XPOWER U.S. Customer Service Department at
8554155-81368
or other numbers
provided on ,w.mower corn.
(3)
Visit XPOWER U.S. Head Office at 240 Clary Ave.. San Gabriel CA 9177E or the most
current address provided on www mower.com .
Please also have your original proof of purchase and the serial number(s) of your
product(s) ready wher you contact XPOWER.
If youAre instructed to return the unit for service or replacement, please:
(1) Request a RMA (Return-Merchandise-Authorization) number.
(2)
Use the original or an equivalent packaging, prepay shipping charges at your own
expense to the address provided by XPOWER, with the RMA number on the shipping
label or the packaging.
(3)
Include all the original parts and components.
XPOWER will inspect, assess and advise the repairs needed and applicable cost, if any.
For products under warranty, we will pay to ship the repaired or replaced product(s) to
you if you use an address within the Contiguous United States. Otherwise, we will ship the
product(s) to you at your own expense.
English -14

English -15

XPOWER
®
XPOWER Manufacture, INC.
240 Clary Avenue
San Gabriel, CA 91776 USA
www.xpovvercom 1 1055)-855-8868 I [email protected]
Read and save these instructions before use
Lea y guarde estas instrucciones antes de user la unidad
Lire et conserver ces instructions avant utilisation
Paper Size: A5/210 min x 148 mm  Index: NA-1-133
Layout: A6/105 min x 148 rnm  Edition: 1.5.Final