XROCKER CERBERUS GAMING OTTOMAN TV BED User manual

CERBERUS GAMING OTTOMAN BED
PLEASE read this leaflet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fitting check list. Do not destroy
any of the packing until you are certain that you have all the necessary part for assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be kept
away from young children while assembling your unit to avoid danger of choking hazards.
COLOUR: RED/BLACK, BLUE/BLACK
SIZE : SINGLE 3',SMALL DOUBLE 4',DOUBLE 4'6''
ASSEMBLY INSTRUCTION
IMPORTANT :
Please reading through this leaflet and then follow the simple step-by-step instruction
Please keep fittings out of children reach.
Please ensure products place on flat & soft surface.
Please ensure you have the right tools, Do Not use power tools to assembly this products.
Please ensure a clean, dry and spacious area for assembly, due to the size of this product we
recommend that it is assembled in the room intended for use.
Please retain these instruction for future reference.
WARNINGS
Ensure products is fully assembled and secured as illustrated before use.
Ensure the legs remain in contact with the ground at all time.
Ensure all screws or bolts are tightened and inspect regularly.
Do Not stand or jump on the product.
Do Not use this product if parts are missing, damage or worn.
Do Not expose this product to dripping or splashing, rain or areas with heavy moisture.
Do Not place the product under direct sunlight, open flames such as candles,heat or radiators.
Keep away from temperatures over 35℃ .
Do Not use scourer, abrasivers or chemical cleaners, only clean with sponge wipe and warm soapy
water.
Page 1 of 7
Do Not let children play with the mechanism.

Fittings
Parts
Page 2 of 7
14x
30mm M8 Bolt
B
4x
Washer M6 x 13mm
D
FG
1x
Spanner
1x
M4 Allen Key
4x
30mm M6 Bolt
C
18x
16mm M8 Bolt
AE
14x
50mm M5 Screw
J
28x
End Slat Cap
I
14x
Centre Slat Cap
H
1x
M5 Allen Key
(2) Footboard x 1pc (3) Side Rail x 2pcs
(1) Headboard x 1pc
R
HEADBOARD
L
HEADBOARD
(5) Long Frame Rail R x 1pc (6) Long Frame Rail L x 1pc
(4) Centre Support Rail x 1pc
(8) Horizontal Frame Rail x 1pcs
(7) Horizontal Frame Rail x 1pcs
(11) Horizontal Support
Bar x 1pc
(12) Footboard Support Rail
(10) Headboard Support Block
x 1pc x 1pc
(14) Slats x 28pcs (15) Feet x 4pcs
(13) Non Woven Fabric x 1pc
(17) Metal Corner Plate x 2pcs
(9) Mattress Stopper x 2pcs
(16) Strap x 1pc

Step 1
Page 3 of 7
Step 2
E
6x
50mm M5 Screw
10x
30mm M8 Bolt
BH
1x
M5 Allen Key
2
E
12
1
10
E
E
E
E
E
1
3
2
3
B
H
BH

Step 3
Step 4
Page 4 of 7
DF
3
2
C
D
C
17
F
1x
M4 Allen Key
4x
Washer M6x13mm
D
4x
30mm M6 Bolt
C
4x
30mm M8 Bolt
BH
1x
M5 Allen Key
11
3
B
H
B

Step 5
Step 6
Page 5 of 7
E
8x
50mm M5 Screw
12x
16mm M8 Bolt
A H
1x
M5 Allen Key
E
13
15
H
A
6
5
7
8
4
A
AH
Headboard
Headboard

Step 7
Step 8
Page 6 of 7
6x
16mm M8 Bolt
AH
1x
M5 Allen Key
G
1x
Spanner
G
Flange Nut
H
A
X6
3
3
Secure the pneumatic lifting mechanisms on
the side rail (3) into place by using flange nuts
as shown.
Do not over tighten the nuts as this will stop
the pneumatic arm rotating freely and could
damage the mounting.

Step 9
Page 7 of 7
J
28x
End Slat Cap
I
14x
Centre Slat Cap
J
I
14
9
9
16
Step 10