XROCKER Cerberus Ottoman Gaming Bed User manual

Page 1 of 7
CERBERUS GAMING OTTOMAN BED
FOR PARTS & TECHNICAL
SUPPORT VISIT :
www.xrockeruk.com/pages/support
SIZE : SINGLE 3'
PLEASE read this leaflet prior to assembly to familiarise yourself with the various stages of construction.
CAUTION: There are small components used in the construction of this unit. These loose items should be kept
away from young children while assembling your unit to avoid danger of choking and/or suffocation hazards.
ASSEMBLY INSTRUCTION
IMPORTANT :
Please read through this leaflet and follow the simple step-by-step instructions.
Please keep all fittings out of the reach of children.
Please ensure the parts placed on a flat & soft surface before assembly.
Please ensure you have the right tools, Do Not use power tools to assembly this product.
Please ensure a clean, dry and spacious area for assembly.
Due to the size of this product we recommend that it is assembled in the room intended for its use.
Please retain these instructions for future reference.
WARNINGS
Ensure the product is fully assembled and secured as illustrated before use.
Ensure the legs always remain in contact with the ground.
Ensure all screws or bolts are tightened and inspect regularly.
Do not stand or jump on the product.
Do not use this product if parts are missing, damage or worn.
Do not expose this product to water or areas with high moisture.
Do not place the product in direct sunlight This could lead to colour fading.
Do not use open flames such as candles, fires or cigarettes.
Do not place the product against a radiator as the heat may melt the covering.
Do not use the product for long periods in rooms over 35 degrees Celsius.
Do not use a scourer, abrasives or chemicals to clean the product, only clean with a sponge wipe and warm
soapy water.
Carefully open the pack supplied and check the contents against the parts and fitting check list. Do not throw
any of the packing away until you are certain that you have all the necessary parts for assembly.

Fittings
Parts
Page 2 of 7
12x
30mm M8 Bolt
B
8x
Washer M6 x 13mm
D
FG
1x
Spanner
1x
M4 Allen Key
KL
1x
Felt Pad
8x
30mm M6 Bolt
C
18x
16mm M8 Bolt
AE
6x
50mm M5 Screw
J
28x
End Slat Cap
I
14x
Centre Slat Cap
H
1x
M5 Allen Key
(2) Footboard x 1pc (3) Side Rail x 2pcs
(1) Headboard x 1pc
R
HEADBOARD
L
HEADBOARD
(5) Long Frame Rail R x 1pc (6) Long Frame Rail L x 1pc
(4) Centre Support Rail x 1pc
(8) Horizontal Frame Rail x 1pcs
(7) Horizontal Frame Rail x 1pcs
(11) Horizontal Support
Bar x 1pc
(12) Footboard Support Rail
(10) Headboard Support Block
x 1pc x 1pc
(14) Slats x 28pcs (15) Feet x 6pcs
(13) Non Woven Fabric x 1pc
(17) Metal Corner Plate x 4pcs
(9) Mattress Stopper x 1pc
(16) Strap x 1pc
6x
30mm M4 Screw

Step 1
Page 3 of 7
Step 2
E
6x
50mm M5 Screw
8x
30mm M8 Bolt
BH
1x
M5 Allen Key
2
E
12
1
10
E
E
E
E
E
1
2
BH
B
H
3
3
B
B

Step 3
Step 4
Page 4 of 7
DI
3
2
C
D
C
17
I
1x
M4 Allen Key
8x
Washer M6x13mm
D
8x
30mm M6 Bolt
C
4x
30mm M8 Bolt
BH
1x
M5 Allen Key
1 &

Step 5
Step 6
Page 5 of 7
12x
16mm M8 Bolt
A H
1x
M5 Allen Key
H
A
6
5
7
8
4
A
AH
Headboard
Headboard
6x
16mm M8 Bolt
AH
1x
M5 Allen Key

Step 7
Step 8
Page 6 of 7
G
1x
Spanner
Secure the pneumatic lifting mechanisms on
the side rail (3) into place by using flange nuts
as shown.
Do not over tighten the nuts as this will stop
the pneumatic arm rotating freely and could
damage the mounting.
F
6x
30mm M4 Screw
13
3
3
To install Bed Foot:
- Left / Right, 30mm from the side ( As per arrow shows )
- Middle, keep at middle point of Headboard / Footboard. ( As per arrow shows )
Middle
30mm
30mm

Step 9
Page 7 of 7
J
28x
End Slat Cap
K
14x
Centre Slat Cap
J
K
14
Step 10
1x
Felt Pad
L
9