XtendLan TC-261 User manual

Fanless VESA Mini PC
TC-261 200MHz Mini PC, 1x LAN
TC-261H 200MHz Mini PC, 1x LAN, HDD mount
RB-261 200MHz Mini PC, 1x LAN, miniPCI
RB-262 200MHz Mini PC, 1x LAN, miniPCI,2xCOM
User’s Manual

User’s manual XtendLAN Fanless VESA mini PC
SAFETY INFORMATION
WARNING
¾Do not expose your computer to rain or moisture, in order to prevent shock and fire
hazard.
¾Never install your computer in wet locations.
¾Do not open the cabinet to avoid electrical shock. Refer to your nearest dealer for
qualified personnel servicing.
¾Never touch un-insulated terminals or wire unless your power adaptor and display
monitor are disconnected.
¾Locate your computer as close as possible to the socket outline for easy access and to
avoid force caused by entangling of your arms with surrounding cables from the
computer.
¾When using Mini PC, avoid using or installing the modem to the serial port during a
storm or a lightning.
¾Do not use the modem or a telephone to report a gas leak in the vicinity of the leak.

User’s manual XtendLAN Fanless VESA mini PC
REGULATORY
FCC CLASS A NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Testing was done with shielded cables. Therefore, in order to comply with the FCC regulations, you must use
shielded cables with your installation.
WARNING
This product Complies with EN55022 Class A. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
as set out in the interference - causing equipment standard entitled “Digital Apparatus”, ICES-003 of the
Department of Communications.
MANUFACTURER’S DECLARATION OF CONFORMITY
This equipment has been tested and found to comply with the requirements of European Community
Council Directives 89/336/EEC and 73/23/EEC relating to electromagnetic compatibility and product
safety respectively.
ATTENTION
This product has been designed and certified to comply with certain regulatory requirements pertaining
to Information Technology Equipment. This product has not been designed for use as a medical device.
Without limitation of the foregoing, this product is not intended and has not been certified for use in a
hospital or clinical environment to diagnose, treat, or monitor patients under medical supervision, and is
not intended and has not been certified to make physical or electrical contact with patients, nor to
transfer energy to or from patients and/or to detect such energy transfer to or from patients.

User’s manual XtendLAN Fanless VESA mini PC
PREFACE
TC-261/TC-261H/RB-261/RB-262 : MINIPC VESA COMPUTER
Revolutionary device that is especially designed for limited physical space and temperature concerns. No
matter you are in a jammed office, a crowded place, or public transportation, it can be easily integrated
with a VESA LCD to bring you VESA PC access at any time.
It can attach to any VESA mounting fixture, allowing it to be securely
mounted onto desks, walls, or buildings, and thereby optimizes your work
area. It can also attach directly to any size LCD for a mobile system for the
use at trade shows, presentations, promotions, etc. Unlike traditional
portable laptop design, the VESA PC can be used with a large size LCD.
Furthermore, with FANLESS design is ideal to be used in the environment
where temperature demand is critical.
So, if you are looking for a device that is able to provide you with more
mobility & space but at the same time uses less power consumption, then
this will be surely meet your need.
The VESA® FDMI™ Standard defines mounting interfaces, hole patterns
and associated cable/power supply locations for LCD monitors, plasma
displays and other flat panel devices. Device is designed to fit this standard
to make monitor attachment quick and easy.
Photo of mounted mini PC on LCD panel display.

User’s manual XtendLAN Fanless VESA mini PC
SPECIFICATION
TC-261 TC-261H RB-261 RB-262
CPU Onboard processor x86, SoC, Fanless
BIOS AMI BIOS, Quick Boot
Chipset SiS 6127
System Memory Onboard 128MB SDRAM
LAN 1x Fast Ethernet RJ-45 Realtek 8100B
Remote Boot ROM built-in boot ROM function, support PXE boot and Wake-up on LAN
MiniPCI none 1x Mini-PCI connector, port for
antenna connector
CF CompactFlash Type I / II
IDE 1 x EIDE (UltraDMA 100) , 44Pin, 2.0 mm Box Header
HDD no space 2,5" HDD
mountable no space no space
Mouse, Keyboard 1 x PS/2 K/B, 1 x PS/2 Mouse
COM - 2x RS-232, 9
pin
USB 3 x USB 1.1 ports (two on front panel)
Display
Chipset Integrated in SoC, AGP 4X, 128-Bit 2D Engine, 8MB shared RAM
Resolution 1280 x 1024 @32 bpp (85Hz)
Audio AC97 2.1 (Codec), H/W DirectSoundTM accelerator,
Audio Interface Line out, Microphone in
Supported OS Windows XP Embedded, Windows CE.NET, Linux
Mechanical &
Environment
Power Requirement +5V @ 3A (5 ~ 5.25V)
Operating Temperature 0 ~ 60 C (-4 – 140 F)
Operating Humidity 0% - 90% relative humidity, non-condensing
Size (W x H x D) 115 x 115 x 135 mm
Weight 505g

User’s manual XtendLAN Fanless VESA mini PC
OVERVIEW
Front Panel
Power LED
The power LED lights up, when system
Is turn on.
HDD LED
The HDD LED flashes when the
system is working. Please do not turn
off the system when HDD start running
Power Switch
Depress switch to turn on & turn off the
systems.
CF Slot
For connection to Device with CF Card
and Micro Driver.
Audio Line Out
Audio Mic InPower Switch
USB port
For connection to devices with USB
interface (keyboard, mouse, HDD, CD-
ROM, Memory Stick, etc.)

User’s manual XtendLAN Fanless VESA mini PC
Back Panel
Power switch
DC Power Jack (3-pin)
PS/2 Keyboard & Mouse (6-pin)
VGA port
RJ-45 LAN Jack
Serial port (RB-262)
USB port
Wireless antenna connector (position on RB-26x)

User’s manual XtendLAN Fanless VESA mini PC
PERIPHERALS
CONNECTING THE POWER ADAPTOR
Power Adaptor
To use your computer immediately, take
and use the supplied AC adapter as a
power source. See the left diagram for
visual connection.
Connect the DC power jack of the
power adaptor to the DC Input jack.
Turning ON Your Computer
Press the power button as indicated
on the figure on your left-side, the
system will start automatically.
CONNECTING THE MONITOR
VGA Connection
Depending on your choice of viewing,
select a conventional CRT or the LCD
VGA monitor.
Make your connection by following the
reference diagram from the VGA
cable of your cable to the 15-pin D-
Sub VGA port.

User’s manual XtendLAN Fanless VESA mini PC
PERIPHERALS
CONNECTING THE USB
USB port are two in front & at the back of the cabinet.
USB Port
The second USB port is available for
connection to USB devices.
Speaker/Earphone
Supports Input/Output device for
speaker and Microphone
Connecting to LAN
There is an available RJ-45 LAN jack
for connection to the hub of your
intranet; and via your server for
internet service (see diagram for RJ-
45 LAN jack).
CONNECTING THE KEYBOARD AND MOUSE The PS/2 Port is available for connect
Keyboard or Mouse. Use supplied octopus to
connect both into one port.

User’s manual XtendLAN Fanless VESA mini PC
CONNECTING SERIAL PORT
Serial Port
The serial port is usually connected to a
serial device like mem. Serial ports
available on RB-262.

User’s manual XtendLAN Fanless VESA mini PC
BIOS
RECONFIGURING
1Take note that AMI BIOS is used in the device. To reconfigure the computer, depress or hit the
<Del> key to enter your BIOS setup main menu.
2Select from the menu, the desired setup for change.
3Press <Esc> to go back to main menu.
4Move your cursor to “Save Settings and Exit”, press “Y” to save the changes that you just made.
Device will restart accordingly to your new setup.

User’s manual XtendLAN Fanless VESA mini PC
APPENDIX
ONBOARD CONNECTORS SUMMARY
SUMMARY TABLE FOR CPU BOARD
Nbr Description Type of Connections Pin nbrs.
J1 VGA Connector D-Sub Connector 8-pin
J2 Power Button Power Button
J3 USB (Back) USB Connector 8-pin
J4 PS/2 keyboard or Mouse Mini DIN Connector 6-pin
J5 RST (Reset) Hear 2x1 2.0mm 2-pin
J6, J7 USB (Front) USB Connector 8-pin
J8 LAN RJ-45 8-pin
J9 Line Out Audio Jack
J10 Mic In Audio Jack
J11 IDE connector Box Header 22x2 2.0mm 44-pin
J12 CF Device Jumper Close : Master 2-pin
J14 DC 5V Input Mini-Din Connector 3-pin
J16,1J7: COM Port Box Header 5x2 2.0mm 10-pin
J18: Mini PCI Mini PCI socket 124-pin

User’s manual XtendLAN Fanless VESA mini PC
PIN ASSIGNMENTS
J4:KBD(PS/2Keyboard & Mouse) – 6-pin Mini-Din
Connector
Pin # Signal Name
1 KBCLK
2 PMCLK
3 GND
4 KBDAT
5 PMDAT
6 SB5V
J8: RJ-45 LAN– 12-pin RJ45 Connector
Pin
# SignalName Pin # SignalName
1 FTXD+ 2 FTXD-
3 FRXIN+ 4 NC
5 NC 6 FRXIN-
7 NC 8 NC
J2: Power Sw – Push Button Switch
Pin # Status
| ON
O OFF

User’s manual XtendLAN Fanless VESA mini PC
J14: DC-IN 5V – 3-pin MINI-DIN Lock Pin Socket
Pin # Signal Name
1 VCC
2 GND
3 NC
J3,J6,J7: USB (USB1x90o)– 4-pin USB Type 1 Connector (Vertical
Type)
Pin # Signal Name
1 VCC
2 USB0-
3 USB0+
4 GND
5 GGND
6 GGND
J1: VGA – 15-pin Dsub Connector
Pin
# SignalName
Pin
# SignalName
Pin
# SignalName
1 MR 6 GND 11 NC
2 MG 7 GND 12 VCC
3 MB 8 GND 13 HYSYNC
4 NC 9 NC 14 VSYNC
5 GND 10 GND 15 VCC
J10: MIC_IN – 5-pin RCA Phone Jack device
Pin # SignalName
1 GND
2 AUD MIC
3 GND
4 GND
5 REF

User’s manual XtendLAN Fanless VESA mini PC
J9: Line-out – 5-pin Phone Jack
Pin # SignalName
1 GND
2 LOUT L
3 NC
4 NC
5 LOUT R
J16, J17: COM1 - 9-pin Dsub Connector
Pin
# SignalName
Pin
# SignalName
1 DCD1 2 RXD1
3 TXD1 4 DTR1
5 GND 6 DSR1
7 RTS1 8 CTS1
9 RI1
Action status
LEDS: POWER ON/OFF & HDD R/W
LED
Color State
Green Power
On
Red
Flashes HDD R/W