Xtreme Power 75023 1.5HP Original instruction manual

OWNER’S MANUAL AND SAFETY INSTRUCTIONS
SPA PUMP
ITEM # 75023 1.5HP, 75024 2HP
SAVE THIS MANUAL. KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY,
OPERATION, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE PRODUCT’S
SERIAL NUMBER ON THE BACK OF THE MANUAL, OR THE MONTH AND YEAR OF PURCHASE IF
PRODUCT HAS NO SERIAL NUMBER
FOR QUESTIONS, PLEASE CALL CUSTOMER SERVICE: 909.628.0880

SAFETY INFORMATION
1
Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in
injury and/or property damage. Save all warnings and instructions for future reference.
The warnings, precautions, and instructions discussed in this instruction manual cannot cover all
possible conditions and situations that may occur. It must be understood by the operator that common
sense and caution are factors which cannot be built into this product, but must be supplied by the
operator.
WARNING – To reduce the risk of injury, do not permit children to use this product unless they are closely
supervised at all times.
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
WARNING – This product is provided with a ground-fault circuit-interrupter integrated with the power plug at
the end of the cord. The GFCI must be tested before each use. With the product operating, push the test button
on the GFCI and the product should not operate. Push the reset button on the GFCI and the product should now
operate normally. When the product fails to operate in this manner, there is a ground current owing indicating
the possibility of an electrical shock. Disconnect the power until the fault has been identied and corrected.
DANGER – Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access
by children. To avoid accidents, ensure that children cannot use this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction ttings in this spa are sized to match the specic water ow created
by the pump. Should the need arise to replace the suction ttings or the pump, be sure that the ow rates are
compatible. Never operate spa if the suction ttings are broken or missing. Never replace a suction tting with
one rated less than the ow rate marked on the original suction tting.
DANGER – Risk of Electric Shock. Install at least 5 feet (1.5 m) from all metal surfaces. DANGER – Risk of
Electric Shock. Do not permit any electric appliance, such as a light,
telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) The water in a spa should never exceed 104°F (40°C). Water temperatures between 100°F (38°C) and 104°F
(40°C) are considered safe for a healthy adult. Lower water temperatures are recommended for young children
and when spa use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal damage during the early months
of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to100°F (38°C).
c) Before entering a spa, the user should measure the water temperature with an accurate thermometer since
the tolerance of water temperature-regulating devices varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with the
possibility of drowning.
e) Persons and persons with a history of heart disease, low or high blood pressure, circulatory system problems,
or diabetes should consult a physician before using a spa.
f ) Persons using medication should consult a physician before using a spa since some medication may induce
drowsiness while other medication may a󰀨ect heart rate, blood pressure, and circulation.
CAUTION: Immediately leave spa if the user feels uncomfortable or sleepy.
SAVE THESE WARNINGS.

SAFETY INFORMATION OPERATION
1 2
SPA PUMP POSITION
If the spa bath pump is supplied separately to the spa bath, position the pump as close as possible to the spa.
This will ensure optimum spa jet performance.
The spa pump must be protected from exposure to weather .It is important to ensure that there is adequate
ventilation provided for the spa pump (minimum area 104 sq cm). Without adequate ventilation the pump motor
will over-heat causing nuisance motor stops and starts. Failure to comply with these instructions may cause
pump damage.
SAVE THESE WARNINGS.
PLUMBING INSTALLATION
The spa bath pumps are supplied complete with integrated barrel unuons to allow easy installation of PVC
pipework. The spa bath pump must be mounted below the normal operating spa bath level but above the spa
bath to ensure correct pump priming and pump/pipe drainage (see Fig.1) All water must drain back into the sap
when emptied .This is in accordance with local Health Department Regulations. Ensure pipes rise evenly from
the spa bath to the spa bath pump to avoid airlocks (otherwise the spa pump will not prime, refer Fig.1).All pipe
connections must be watertight. Never allow spa pump to run without water as this may result in damage to the
pump sea.
Special Note:
To avoid water damage to property from leaking connections or normal wear, the pump must be installed on a
well drained site or a properly constructed drain tray.
ELECTRICAL CONNECTION
Plug the spa pump power cord into a dedicated power socket and switch the power on. All spa bath pumps must
be installed in accordance with relevant electrical standards. Terminal box cover should be securely in place
before connecting the pump to electricity to prevent electric shock or injury. Motor is tted with auto-rest thermal
switch and may restart without warning. our spa pumps are suitable for connection to 110-120/220-240volt 60Hz
power outlets. Some models will require a 12Amp outlet .Check motor I.D. label for details. All pumps must have
a dedicated power supply.

TROUBLESHOOTING
3
OPERATING SPA BATH PUMPS
Before lling and starting your spa bath, ensure that the spa bath is free from debris or any material that may
cause blockage to the pump or impeller. Fill the bath to a minimum 50 mm above the spa jets and check before
switching on that there are no visible leaks from pipework or connections .To start pump, depress the air button
on the spa bath. This will purge air from the plumbing and spa jets. After a short period of time the spa jets will
start to opetate nonnally. To stop spa jet operation depress the air button again.
4
OF NOTE
OF NOTE

OF NOTE
4
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
MADE IN CHINA
OF NOTE
OF NOTE